Physics › Section J · Thermodynamics › Topic J.2
Simple thermodynamic processes
Every engine is built from a few simple steps: heating a gas at constant pressure or constant volume, letting it expand at constant temperature, or squeezing it so fast that no heat can escape. A pressure-volume diagram shows each step at a glance, including how much work it does.
A gas in a cylinder
Picture gas trapped in a cylinder under a movable piston. Burn fuel nearby and heat flows into the gas, raising its temperature and pressure, so it pushes the piston out and does work. To repeat the trick the piston must come back, which is easier if the gas is cooled first so that it pushes back less. Car engines repeat versions of this sequence many times a second, so start with the simple steps and the work each one does. Throughout, the first law is \(\Delta U = Q - W\), with \(W\) the work done by the gas.
Work done by an expanding gas
A gas at pressure \(P\) pushes on a piston of area \(A\) with force \(F = PA\). If the piston moves out a distance \(d\) while the pressure stays constant, the work done by the gas is \(Fd = PAd\). But \(Ad\) is the change in volume, so
With \(P\) in pascals and \(\Delta V\) in cubic metres, \(W\) comes out in joules, because \(\text{Pa}\cdot\text{m}^3 = \text{N}\cdot\text{m} = \text{J}\). Expansion makes \(\Delta V\) positive, so the gas does positive work. Compression makes it negative: the surroundings do work on the gas. The formula assumes the piston moves slowly enough for the pressure to stay uniform.
PV diagrams and area
A PV diagram plots a gas's pressure on the vertical axis against its volume on the horizontal axis, so each point is a state and each line is a process. For a constant-pressure step the graph is a horizontal line, and \(P\Delta V\) is the area of the rectangle beneath it. This generalises: when the pressure varies, slice the region into thin strips, each with nearly constant pressure, and add their areas. The work done by the gas equals the area under the path, counted positive when the path runs to the right (expansion) and negative when it runs to the left. Two paths between the same states can enclose different areas, so work depends on the path.
Isobaric: constant pressure
In an isobaric process the pressure is constant, so \(W = P\Delta V\). For an ideal gas, \(PV = nRT\) shows that at fixed pressure the volume is proportional to the kelvin temperature, so an isobaric expansion needs the gas to warm up. That takes heat: enough to supply both the work done and the rise in internal energy, since \(Q = \Delta U + W\). Gas heated under a freely sliding, weighted piston follows an isobaric path.
Worked example: an isobaric expansion
Gas at a constant \(1.50 \times 10^5\) Pa absorbs 1200 J of heat and expands from \(2.00 \times 10^{-3}\ \text{m}^3\) to \(5.00 \times 10^{-3}\ \text{m}^3\). Find \(W\) and \(\Delta U\). 1. Volume change: \(\Delta V = 3.00 \times 10^{-3}\ \text{m}^3\). 2. Work: \(W = (1.50 \times 10^5)(3.00 \times 10^{-3}) = 450\) J. 3. First law: \(\Delta U = 1200 - 450 = 750\) J. 4. Check: \(U\) rose, so the temperature rose, as it must when a gas expands at constant pressure; for an ideal gas the volume grew 2.5 times, so the kelvin temperature did too.
Isochoric: constant volume
In an isochoric process the volume is fixed, as in a sealed rigid can. The piston does not move, so \(W = 0\), and on a PV diagram the path is a vertical line with no area beneath it. The first law becomes \(\Delta U = Q\): every joule of heat goes into internal energy, raising the temperature and pressure. For example, heating 0.200 mol of a monatomic ideal gas from 300 K to 400 K at constant volume needs
Cooling at constant volume reverses this, removing internal energy as heat.
Isothermal: constant temperature
In an isothermal process the temperature is held constant. For an ideal gas, internal energy depends only on temperature, so \(\Delta U = 0\) and the first law gives \(Q = W\). As the gas expands it does work, and exactly that much heat must flow in from the surroundings to stop it cooling. With \(T\) fixed, \(PV = nRT\) means \(PV\) is constant: the path is a curve, a hyperbola, that falls as the volume grows. Isothermal processes must be slow, so that heat has time to flow and the gas stays at one temperature throughout.
Adiabatic: no heat flow
In an adiabatic process no heat crosses the boundary, so \(Q = 0\) and \(\Delta U = -W\). Insulation helps, but speed is often enough, because a quick process leaves no time for heat to flow. A gas expanding adiabatically does work at the expense of its own internal energy, so it cools. Rising air expands and cools this way, which is why clouds form as moist air rises. Compress a gas adiabatically and the work done on it heats it: a bicycle pump gets warm, and a diesel engine ignites its fuel with no spark, using air made hot by rapid compression. On a PV diagram an adiabatic expansion falls more steeply than an isothermal one from the same starting point.
Worked example: work around a cycle
A gas goes round a rectangle on a PV diagram. A to B: expansion at \(3.00 \times 10^5\) Pa from 1.00 L to 4.00 L. B to C: cooling at constant volume to \(1.20 \times 10^5\) Pa. C to D: compression back to 1.00 L at that pressure. D to A: heating at constant volume. 1. With 1 L = \(10^{-3}\ \text{m}^3\): \(W_{AB} = (3.00 \times 10^5)(3.00 \times 10^{-3}) = 900\) J. 2. The two isochoric legs do no work. 3.
4. Net work: \(540\) J. 5. Check: the enclosed area is \((1.80 \times 10^5)(3.00 \times 10^{-3}) = 540\) J. The loop runs clockwise, so the net work is positive, and because \(\Delta U = 0\) over a full cycle, the net heat in is also 540 J.
Reversible processes
Run a process backwards; if the system and its surroundings both end exactly where they began, the process is reversible. Slow isothermal and adiabatic processes are reversible in principle. Real processes never quite are: friction and turbulence turn some work into heat whichever way the piston moves, and heat that crosses a finite temperature difference never flows back by itself. Reversibility is an ideal, like a frictionless surface, but it sets the limits explored in the next topics.
Common mistakes to avoid
First, using litres in \(W = P\Delta V\) with pascals: convert to cubic metres, or the answer is a thousand times too large. Second, giving compression positive work; with \(W\) done by the gas, compression is negative. Third, thinking isothermal means no heat flows; it means no temperature change, and the heat in equals the work out. Fourth, confusing isothermal with adiabatic: an adiabatic process has no heat flow, but its temperature changes. Fifth, multiplying the pressure by the final volume instead of the change in volume.
Key takeaways
The work done by a gas is the area under its path on a PV diagram: positive for expansion, negative for compression, and path dependent. Isobaric: constant P, W = PΔV. Isochoric: constant V, W = 0, ΔU = Q. Isothermal: constant T, so for an ideal gas ΔU = 0 and Q = W. Adiabatic: Q = 0, so ΔU = −W; expansion cools and compression heats. Over a cycle ΔU = 0, and the net work is the area inside the loop, positive when it runs clockwise. Reversible processes are an ideal that real ones approach.
Flashcards
Flashcard
Work done by a gas at constant pressure
Test your understanding
Question 1 of 5
A gas at a constant 2.00 × 10⁵ Pa expands from 0.0100 m³ to 0.0250 m³. How much work does it do?
Question 2 of 5
An ideal gas expands isothermally and does 500 J of work. What heat flows, and in which direction?
Question 3 of 5
300 J of heat is added to a gas held at constant volume. What are W and ΔU?
Question 4 of 5
A gas is compressed adiabatically, with 250 J of work done on it. What happens to its internal energy and temperature?
Question 5 of 5
A gas runs clockwise round a rectangle on a PV diagram between 1.00 × 10⁵ Pa and 4.00 × 10⁵ Pa, and between 2.00 × 10⁻³ m³ and 5.00 × 10⁻³ m³. What net work does it do per cycle?
