Physics › Section N · Electric potential and capacitance › Topic N.2

Potential in a uniform field

Connect a battery across two parallel metal plates and a uniform electric field appears between them. In that simple set-up the link between voltage and field is just a division, and it explains everything from electron guns to sparks.

Two ways to describe the same field

An arrangement of charges can be described by its electric field \(E\), a vector tied to the force on a charge, or by its potential \(V\), a scalar tied to energy. They must be connected, because force and energy are connected through work. The cleanest place to find the connection is between two large, parallel conducting plates with equal and opposite charges. Away from their edges, the field there is uniform: the same size and direction everywhere, pointing straight from the positive plate to the negative one, as the topic on field lines showed.

From work to E = V/d

Move a positive test charge \(q\) from the positive plate A to the negative plate B, a distance \(d\) along the field. The force \(qE\) is constant and points along the motion, so the field does work \(W = qEd\). The same work equals minus the change in potential energy: \(W = -q(V_B - V_A) = qV_{AB}\), where \(V_{AB} = V_A - V_B\) is the voltage between the plates. Setting the two expressions equal, \(q\) cancels:

V_{AB} = Ed \quad \text{or} \quad E = \frac{V_{AB}}{d}

This holds only for a uniform field, with \(d\) measured along the field direction.

Volts per metre

The equation \(E = V/d\) gives the field a second unit, the volt per metre. It is exactly the same as the newton per coulomb used for fields so far, because a volt is a joule per coulomb and a joule is a newton metre:

\frac{\text{V}}{\text{m}} = \frac{\text{J}}{\text{C}\cdot\text{m}} = \frac{\text{N}\cdot\text{m}}{\text{C}\cdot\text{m}} = \frac{\text{N}}{\text{C}}

Use whichever suits the problem. Engineers designing insulation think in volts per metre, or kilovolts per millimetre, while force problems read more naturally in newtons per coulomb.

The field points downhill in potential

Between the plates the potential falls steadily from the positive plate to the negative one, by \(E\) volts for every metre travelled along the field. If the negative plate is at 0 V, a point a distance \(x\) from it is at \(V = Ex\). The field always points in the direction in which the potential decreases, and its size is how quickly the potential falls with distance. In any region, uniform or not, the average component of the field along a direction is \(E = -\Delta V / \Delta s\), where the minus sign says the field points towards lower potential. A steep fall in potential means a strong field.

Worked example: an electron between plates

Two parallel plates 6.00 mm apart have a potential difference of 1.50 kV. Find the field between them and the force on an electron there, and compare it with the electron's weight (\(m = 9.109 \times 10^{-31}\) kg). 1. Field: \(E = \frac{1.50 \times 10^3\ \text{V}}{6.00 \times 10^{-3}\ \text{m}} = 2.50 \times 10^5\) V/m. 2. Force:

F = eE = (1.602 \times 10^{-19})(2.50 \times 10^5) = 4.01 \times 10^{-14}\ \text{N}

towards the positive plate, because the electron is negative. 3. Weight: \(mg = (9.109 \times 10^{-31})(9.80) = 8.93 \times 10^{-30}\) N. 4. The electric force is about \(4.5 \times 10^{15}\) times larger, so ignoring gravity is fully justified. The force is the same at every point between the plates.

Worked example: a point between the plates

Plates 4.00 cm apart are held at +200 V and 0 V. Find the potential at point P, 1.50 cm from the 0 V plate, and the change in potential energy of a proton that moves from P to the 0 V plate. 1. Field: \(E = \frac{200\ \text{V}}{0.0400\ \text{m}} = 5.00 \times 10^3\) V/m. 2. Potential at P: \(V_P = Ex = (5.00 \times 10^3)(0.0150) = 75.0\) V. 3. Proton: \(\Delta PE = q\Delta V = e(0 - 75.0\ \text{V}) = -75.0\) eV, or \(-1.20 \times 10^{-17}\) J. 4. Check: P is 1.50/4.00 = 37.5% of the way from the 0 V plate, and 37.5% of 200 V is 75.0 V. The proton loses PE moving to lower potential, as a positive charge should.

Energy gained across the plates

A charge accelerated from rest across the whole gap gains kinetic energy \(|q|V_{AB}\), whatever the separation. Pull the plates twice as far apart at the same voltage and the field halves, so the force halves, but it now acts over twice the distance, and \(Fd\) is unchanged. The separation changes how hard the charge is pushed and how long the trip takes, not the energy at the end. That is why electron guns and particle accelerators are rated by their voltage: a 25 kV gun gives each electron 25 keV.

Breakdown: when air conducts

Insulators survive only up to a certain field. Dry air at everyday pressure breaks down at roughly \(3 \times 10^6\) V/m: stray free electrons are then accelerated hard enough between collisions to knock more electrons off gas molecules, an avalanche of ions and electrons forms, the air conducts, and a spark jumps. For a uniform field this sets the largest voltage a gap of width \(d\) can hold, \(V_{\max} = E_{\max}d\). Sharp points and edges concentrate the field, so real sparks often start at a lower voltage than this estimate.

Worked example: a stove igniter

A gas-stove igniter makes its spark across a gap of 4.0 mm. Treating the field in the gap as uniform and using a breakdown field of \(3.0 \times 10^6\) V/m for air, what voltage is needed? 1. Convert the gap: \(d = 4.0 \times 10^{-3}\) m. 2. Use \(V_{\max} = E_{\max}d = (3.0 \times 10^6\ \text{V/m})(4.0 \times 10^{-3}\ \text{m})\). 3. Result: \(V = 1.2 \times 10^4\) V, or 12 kV, quoted to two figures because the breakdown field is approximate. 4. Check: 3 kV per millimetre times 4 mm is 12 kV.

Common mistakes to avoid

First, leaving \(d\) in millimetres or centimetres: \(E = V/d\) needs metres to give V/m. Second, using \(E = V/d\) where the field is not uniform, such as near a point charge. Third, measuring \(d\) along a slanted path instead of along the field. Fourth, pointing the field towards higher potential; it always points to lower potential. Fifth, thinking a wider gap gives a charge more energy at the same voltage: the energy depends on the voltage only.

Key takeaways

Between large parallel plates the field is uniform, and the voltage and field are linked by V = Ed, or E = V/d, with d along the field in metres. The volt per metre equals the newton per coulomb. The field points from high to low potential, and potential falls by E volts per metre along it; in general the average field component along a direction is E = −ΔV/Δs. A charge crossing from rest gains energy |q|V whatever the gap. Dry air breaks down near 3 × 10⁶ V/m, which limits the voltage a gap can hold: V(max) = E(max)d.

Flashcards

Flashcard

Uniform field

Same size and direction everywhere, as between large parallel plates

Away from the plate edges.

Test your understanding

Question 1 of 5

A 24.0 V battery is connected across parallel plates 3.00 mm apart. What is the field between them?

Question 2 of 5

Using a breakdown field of 3.0 × 10⁶ V/m for dry air, what is the largest voltage a uniform 2.0 mm air gap can hold?

Question 3 of 5

Which way does the electric field point between two parallel plates?

Question 4 of 5

Plates 5.00 cm apart are held at 100 V and 0 V. What is the potential at a point 2.00 cm from the 0 V plate?

Question 5 of 5

An electron starts from rest at one plate and crosses to the other. If the plate separation is doubled while the voltage stays the same, what happens to the kinetic energy it has on arrival?

← Previous topicNext topic →