Statics › Section G · Centroids and centers of gravity › Topic G.2

Center of gravity and center of mass

Every free-body diagram so far has drawn an object's weight as one arrow at one point. This topic finds that point, the centre of gravity, and its close partner, the centre of mass.

One arrow for the whole weight

Gravity pulls on every particle of a body, so the real weight is a huge number of tiny parallel forces. Drawing them all is impossible, so earlier topics replaced them with a single arrow. That replacement is only legitimate if the single force has the same external effect as all the small ones: the same total force and the same moment about every point. The point where it must act is the centre of gravity, written CG, with coordinates \((\bar{x}, \bar{y}, \bar{z})\). Balance a ruler on one finger and your finger finds the CG by trial and error.

Finding the balance point with moments

Take two weights \(W_1\) and \(W_2\) acting downward at \(x_1\) and \(x_2\), with both positions positive. With counterclockwise moments positive, a downward force to the right of the origin O turns clockwise, so the total moment about O is \(-x_1W_1 - x_2W_2\). A single equivalent weight \(W = W_1 + W_2\) at \(\bar{x}\) has moment \(-\bar{x}W\). Setting the two equal, as the topic "Statically equivalent systems and resultants" requires, gives

\bar{x} = \frac{x_1W_1 + x_2W_2}{W_1 + W_2}

This is a weighted average of position, with weight as the weighting factor.

The general formulas

For a body split into any number of parts, part \(i\) having weight \(W_i\) whose own CG is at \((\bar{x}_i, \bar{y}_i, \bar{z}_i)\):

\bar{x} = \frac{\sum \bar{x}_iW_i}{\sum W_i} \quad \bar{y} = \frac{\sum \bar{y}_iW_i}{\sum W_i} \quad \bar{z} = \frac{\sum \bar{z}_iW_i}{\sum W_i}

Each numerator is a first moment of weight, a sum of weights times distances; the denominator is the total weight. The CG is fixed in the body, but its coordinates depend on where you put the origin. If a body's shape and weight are both symmetric about a plane, every part on one side is matched by an equal part on the other, the first moment about that plane is zero, and the CG lies in it.

Worked example: crates on a platform

Crates of 40 N, 60 N and 100 N sit along a platform with their CGs at \(x = 0.3\) m, 1.0 m and 2.2 m. 1. Total weight: \(W = 200\) N. 2. First moment:

40(0.3) + 60(1.0) + 100(2.2) = 292\ \mathrm{N \cdot m}

3. \(\bar{x} = 292/200 = 1.46\) m. 4. Now move the origin to the 100 N crate, so the positions become \(-1.9\), \(-1.2\) and 0 m. Then

\bar{x} = \frac{40(-1.9) + 60(-1.2)}{200} = -0.74\ \text{m}

5. Check: \(2.2 - 1.46 = 0.74\), so both answers name the same physical point. Only the coordinate changed.

Centre of mass

The centre of mass is the average location of a body's mass. Since each part's weight is \(W_i = m_i g\), substituting into the CG formulas gives \(g\) in every term of the numerator and denominator. If \(g\) is the same at every particle it cancels:

\bar{x} = \frac{\sum \bar{x}_i m_i}{\sum m_i}

and likewise for \(\bar{y}\) and \(\bar{z}\). The numerator is now a first moment of mass. Near Earth's surface take \(g = 9.81\ \mathrm{m/s^2}\), or \(32.2\ \mathrm{ft/s^2}\) in US customary units. For any body small compared with Earth, \(g\) barely changes across it, so the centre of mass and the CG are the same point and the terms are used interchangeably.

Worked example: a loaded forklift

Measure \(x\) forward from a forklift's front axle. The body (3000 kg) has its centre of mass at \(x = -1.1\) m, the counterweight (1500 kg) at \(-2.0\) m and the load (1200 kg) at \(+0.6\) m, ahead of the axle. The rear axle is at \(-1.8\) m. 1. Total mass: 5700 kg. 2. First moment of mass:

3000(-1.1) + 1500(-2.0) + 1200(0.6) = -5580\ \mathrm{kg \cdot m}

3. \(\bar{x} = -5580/5700 = -0.979\) m. 4. The truck's weight, \(5700 \times 9.81 = 55.9\) kN, acts between the axles, so both axles carry load and the truck does not tip forward. 5. Check: the heavy rear parts pull \(\bar{x}\) well behind the front axle.

Locating a CG by experiment

For an irregular flat object, hang it freely from one point and draw the vertical line through that point with a plumb line; in equilibrium the CG must lie on it, because otherwise the weight would have a moment about the pin. Hang it from a second point and draw another line. The CG is where they cross. For large objects such as cars and aircraft, engineers weigh each wheel or axle on its own scale, then use a moment balance to find the CG. Aircraft must be loaded so that the CG stays within limits set by the manufacturer.

Worked example: weighing a car

A car with a 2.80 m wheelbase is driven onto two scales, which read 8.0 kN under the front axle and 6.0 kN under the rear. Where is its CG? 1. Total weight: \(W = 8.0 + 6.0 = 14.0\) kN, so the mass is \(14{,}000/9.81 = 1427\) kg. 2. Take moments about the front axle with \(d\) the distance back to the CG: the weight's moment \(Wd\) must balance the rear reaction's moment, \(6.0 \times 2.80\). 3. \(d = \frac{6.0 \times 2.80}{14.0} = 1.20\) m behind the front axle. 4. Check about the rear axle: \(\frac{8.0 \times 2.80}{14.0} = 1.60\) m, and \(1.20 + 1.60 = 2.80\) m. The CG sits nearer the axle carrying more weight.

Stability and tipping

A body resting on a base stays upright while the vertical line through its CG falls inside the base. Tilt a crate 1.2 m wide with its CG 0.9 m above the floor at its centre: it pivots on one bottom edge and falls over once the CG passes above that edge, at a tilt of \(\theta = \tan^{-1}(0.6/0.9) = 33.7^\circ\), provided it does not slide first. A lower CG or a wider base raises that angle. This is why racing cars sit low and why a lorry with a high load is more likely to roll on a sharp bend.

Common mistakes to avoid

First, averaging positions without weighting them: the crates above are not centred at the plain mean of 1.17 m. Second, dropping signs when parts lie on the negative side of the origin. Third, thinking the CG moves when the axes do; only its coordinates change. Fourth, mixing mass and weight in one formula, such as kilograms in the numerator and newtons in the denominator. Fifth, in the scale method, dividing by the wheelbase instead of by the total weight.

Key takeaways

The CG is the point where a single force equal to the total weight has the same external effect as all the distributed weights. Its coordinates are first moments of weight divided by total weight, such as \(\bar{x} = \sum \bar{x}_iW_i / \sum W_i\). Replacing \(W_i\) with \(m_i g\) and cancelling a uniform \(g\) gives the centre of mass, which coincides with the CG for ordinary bodies. Symmetry puts the CG on a plane of symmetry. Plumb lines and wheel scales find it by experiment, and a body tips once the vertical through its CG leaves its base.

Flashcards

Flashcard

Centre of gravity (CG)

The point where the whole weight can act with the same external effect

Coordinates (x̄, ȳ, z̄).

Test your understanding

Question 1 of 5

Loads of 50 N at x = 0, 150 N at x = 2.0 m and 100 N at x = 3.0 m act on a beam. Where is their centre of gravity?

Question 2 of 5

A van with a 2.5 m wheelbase reads 9.0 kN on the front scale and 6.0 kN on the rear scale. How far behind the front axle is its CG?

Question 3 of 5

When are a body's centre of mass and centre of gravity the same point?

Question 4 of 5

A uniform crate 1.0 m wide has its CG 0.8 m above the floor, centred. If it is tilted slowly about one bottom edge without sliding, at what angle does it tip over?

Question 5 of 5

A system's CG is at x = 1.2 m. The origin is moved to the point that used to be x = 2.0 m. What happens?

← Previous topicNext topic →