Statics › Section G · Centroids and centers of gravity › Topic G.3

Centroids

Strip away the material and keep only the shape, and the centre of gravity becomes the centroid: a purely geometric point that every beam section, plate and load diagram in statics relies on.

A centre for pure shapes

The centre of gravity belongs to a physical object, because it is weighted by weight. Engineers also need the centre of a shape on paper: the cross-section of a beam, the outline of a gate, the area under a load diagram. Weighting position by a geometric quantity instead of a physical one gives that point, the centroid. It depends only on geometry, so a steel plate and a cardboard cut-out of the same outline have the same centroid. Later topics use it for distributed loads, water pressure and moments of inertia.

Defining the centroid

For a two-dimensional shape split into parts of area \(A_i\), each with its own centroid at \((\bar{x}_i, \bar{y}_i)\), the weighting factor is area:

\bar{x} = \frac{\sum \bar{x}_iA_i}{\sum A_i} \qquad \bar{y} = \frac{\sum \bar{y}_iA_i}{\sum A_i}

A solid uses volume \(V_i\) in place of area and gains a third coordinate \(\bar{z}\). A thin wire or a curve uses length \(L_i\). The structure is exactly the centre of gravity formula with a different weight, so everything learned about weighted averages carries over.

First moments of area

The numerators have their own names. The first moment of area about the \(x\)-axis is \(Q_x = \sum \bar{y}_iA_i\), and about the \(y\)-axis it is \(Q_y = \sum \bar{x}_iA_i\). The subscripts cross on purpose: distance from the \(x\)-axis is measured by \(y\). Then \(\bar{x} = Q_y/A\) and \(\bar{y} = Q_x/A\). First moments have units of length cubed, such as \(\mathrm{mm^3}\), and a moment about an axis through the centroid is zero. The calculus topic "Moments, centres of mass, and centroids" writes the same quantities as \(M_x\) and \(M_y\).

When centroid, centre of mass and CG coincide

Take a plate of constant thickness \(t\) and density \(\rho\). A part of area \(A_i\) weighs \(W_i = \rho g t A_i\). Substituting into the centre of gravity formula, the constant \(\rho g t\) appears in every term above and below the line and cancels, leaving the centroid formula. The same happens for any homogeneous solid, where \(W_i = \rho g V_i\). So for uniform bodies the centroid, centre of mass and centre of gravity are one point. If density or thickness varies, they separate: a plate that is half steel and half aluminium has its centre of gravity shifted from the centre into the steel half.

Symmetry does the work

If a shape is symmetric about a line, every small piece on one side has a mirror piece at the same distance on the other, with opposite sign. Their first moments about that line cancel in pairs, so the centroid lies on the line of symmetry. With two lines of symmetry, it lies where they cross. That is why the centroid of a rectangle, a circle, a square tube or an I-beam with equal flanges is at its geometric centre, with no calculation at all. A shape with only one line of symmetry gives you one coordinate free and leaves the other to compute.

Worked example: two steel sections

An I-section has two flanges 150 mm wide and 12 mm thick joined by a central web 8 mm thick and 200 mm tall, so it is 224 mm deep overall. Put the origin at the bottom-left corner of the lower flange. 1. The section is symmetric about the vertical line \(x = 75\) mm and about the horizontal line \(y = 112\) mm. 2. So \(\bar{x} = 75\) mm and \(\bar{y} = 112\) mm. Now cut off the parts of both flanges that stick out to the left of the web, leaving a channel that opens to the right. 3. It keeps only the horizontal line of symmetry, so \(\bar{y} = 112\) mm still, but \(\bar{x}\) needs the composite method of the next topic.

Centroids of standard shapes

A rectangle's centroid is at its centre. Any triangle's centroid is where its medians meet, at the average of its three vertices' coordinates, which puts it one third of the height above any side taken as base. For a right triangle with legs \(b\) and \(h\) on the axes, that is \((b/3,\ h/3)\) from the right angle. A semicircle of radius \(r\) has its centroid on its axis of symmetry, \(4r/(3\pi) \approx 0.424r\) from the straight edge. A quarter circle's centroid is \(4r/(3\pi)\) from each straight edge. A trapezoid of height \(h\) with parallel sides \(a\) on top and \(b\) at the bottom has

\bar{y} = \frac{h(2a + b)}{3(a + b)}

above the bottom side.

Worked example: a gusset plate

A steel gusset plate is a right triangle with its right angle at the origin, a 300 mm leg along the \(x\)-axis and a 450 mm leg along the \(y\)-axis. It is 10 mm thick, with steel density 7850 \(\mathrm{kg/m^3}\). 1. Centroid: \(\bar{x} = 300/3 = 100\) mm and \(\bar{y} = 450/3 = 150\) mm. 2. Check with the vertex average: \(\frac{0 + 300 + 0}{3} = 100\) and \(\frac{0 + 0 + 450}{3} = 150\). 3. Area: \(\tfrac{1}{2}(0.300)(0.450) = 0.0675\ \mathrm{m^2}\). 4. Mass: \(7850 \times 0.0675 \times 0.010 = 5.30\) kg, so with \(g = 9.81\ \mathrm{m/s^2}\) the weight is \(5.30 \times 9.81 = 52.0\) N. 5. The plate is uniform, so that weight acts at (100, 150) mm.

Checking a centroid

Three quick checks catch most errors. The centroid must lie inside the shape's bounding box. It must sit on every line of symmetry. And it should sit towards the bulk of the area: for the trapezoid formula with \(a = 2\) m, \(b = 4\) m and \(h = 3\) m, \(\bar{y} = \frac{3(8)}{18} = 1.33\) m, below mid-height because the wide side is at the bottom. Setting \(a = 0\) turns the trapezoid into a triangle and gives \(h/3\), another useful test. The centroid need not lie on material: for a ring or an L-shape it can sit in empty space.

Common mistakes to avoid

First, measuring standard-shape centroids from the wrong edge: a triangle's centroid is one third of the height from the base, which is two thirds from the opposite vertex. Second, guessing \(r/2\) for a semicircular plate, or using the semicircular-arc value \(2r/\pi\), which belongs to a bent wire, not to an area. Third, crossing \(Q_x\) and \(Q_y\) the wrong way. Fourth, assuming a centroid is a centre of gravity when the material is not uniform. Fifth, forgetting that table values are measured from a stated corner or edge and must be shifted to your own axes.

Key takeaways

A centroid is a weighted average of position with area, volume or length as the weight, so it depends on geometry alone. \(\bar{x} = Q_y/A\) and \(\bar{y} = Q_x/A\), with first moments in length cubed. For uniform bodies the centroid, centre of mass and centre of gravity coincide. A centroid lies on every line of symmetry. Standard results: rectangle at its centre; triangle at the vertex average, \(h/3\) above a base; semicircle and quarter circle \(4r/(3\pi)\) from the straight edges.

Flashcards

Flashcard

Centroid

The geometric centre of a shape: position weighted by area, volume or length

No material properties involved.

Test your understanding

Question 1 of 5

A right triangle has its right angle at the origin, a 600 mm leg along the x-axis and a 900 mm leg along the y-axis. Where is its centroid?

Question 2 of 5

How far from its straight edge is the centroid of a semicircular plate of radius 300 mm?

Question 3 of 5

A square plate of uniform thickness is made of steel on its left half and aluminium on its right half. Which statement is true?

Question 4 of 5

A section is symmetric about the vertical line x = 80 mm and has no other line of symmetry. What does this tell you?

Question 5 of 5

A triangle has vertices at (0, 0), (12, 0) and (6, 9) cm. Where is its centroid?

← Previous topicNext topic →