Statics › Section G · Centroids and centers of gravity › Topic G.7
Distributed loads
Snow on a roof, books on a shelf and a floor full of people are loads spread along a length rather than forces at a point. Each can be replaced by one resultant force: its size is the area under the load diagram, and it acts through that area's centroid.
Loads that are spread out
Most real loads are not concentrated at a point. A beam carries its own weight along its whole length; a roof carries snow; a retaining wall carries soil or water pressure over its face. Treating these as a handful of point forces would be clumsy and inaccurate. Instead, statics describes them by how much force arrives per unit length, and then uses the centroid ideas of this section to replace the spread load with a single equivalent force that the equilibrium equations can use.
Load intensity
A distributed load on a beam is described by its intensity \(w(x)\), the force per unit length at position \(x\), in N/m or kN/m (lb/ft in US customary units). It is drawn as a row of arrows whose tips trace the load curve. A uniformly distributed load has the same intensity everywhere. Loads on surfaces are given per unit area, in Pa or kPa: a floor load of 2.5 kPa means 2.5 kN on every square metre. If floor joists are spaced 0.4 m apart, each joist collects the load from a 0.4 m wide strip, so it carries \(2.5 \times 0.4 = 1.0\) kN/m.
The equivalent resultant
A tiny length \(dx\) carries a force \(dF = w\,dx\), with moment \(x\,dF\) about the origin. A single force is statically equivalent, in the sense of the topic "Statically equivalent systems and resultants", if it matches the total force and the total moment:
The first integral is the area under the load diagram. The second is the \(x\)-coordinate of that area's centroid. So the resultant equals the area of the load diagram and its line of action passes through the area's centroid. The height of the centroid does not matter, since a force can slide along its line of action.
Uniform and triangular loads
Two shapes cover most problems. A uniform load \(w_0\) over length \(L\) is a rectangle: \(F_R = w_0L\), acting at the middle. A load rising linearly from zero to \(w_0\) over length \(L\) is a triangle: \(F_R = \tfrac{1}{2}w_0L\), acting at the triangle's centroid, two thirds of the way from the zero end, which is one third of the way from the high end. A uniform load of 4 kN/m on a 6 m span is 24 kN at 3 m. A load rising from 0 to 6 kN/m over 3 m is 9 kN at 2 m from the zero end.
Worked example: a trapezoidal load
A load rises linearly from 3 kN/m at \(x = 0\) to 7 kN/m at \(x = 5\) m. 1. Split the trapezoid into a 3 kN/m rectangle and a triangle rising from 0 to 4 kN/m. 2. Rectangle: \(3 \times 5 = 15\) kN at 2.5 m. 3. Triangle: \(\tfrac{1}{2}(4)(5) = 10\) kN at \(\tfrac{2}{3}(5) = 3.33\) m. 4. Total: \(F_R = 25\) kN. 5. Location, as a composite centroid:
6. Check with the trapezoid formula from "Centroids": \(\frac{5(2 \times 7 + 3)}{3(7 + 3)} = 2.83\) m from the 3 kN/m end, just past the middle and towards the heavier end.
Worked example: reactions of a simple beam
A 6 m beam has a pin at A (\(x = 0\)) and a roller at B (\(x = 6\) m). It carries 4 kN/m over its left 3 m and a 10 kN point load at \(x = 4.5\) m. 1. Replace the distributed load by 12 kN at \(x = 1.5\) m. 2. Moments about A, counterclockwise positive:
so \(B_y = 10.5\) kN. 3. Vertical forces: \(A_y + 10.5 - 12 - 10 = 0\), so \(A_y = 11.5\) kN. 4. No horizontal loads, so \(A_x = 0\). 5. Check with moments about B: \(-6(11.5) + 12(4.5) + 10(1.5) = 0\). A carries more because more load sits on its side.
Worked example: a cantilever
A 3 m cantilever is built into a wall at A and projects horizontally to the right; it carries a triangular load from 6 kN/m at the wall down to zero at the free end. 1. Resultant: \(\tfrac{1}{2}(6)(3) = 9\) kN. 2. It acts one third of the length from the high end, 1 m from the wall. 3. Vertical forces: \(A_y = 9\) kN upward. 4. Moments about A, counterclockwise positive: the downward 9 kN at 1 m gives \(-9\) kN·m, so \(M_A - 9 = 0\) and \(M_A = 9\) kN·m, counterclockwise. 5. Check: had the load peaked at the free end, its resultant would sit 2 m out and \(M_A\) would double to 18 kN·m.
Loads given by a function
When \(w(x)\) is a curve, integrate. The load \(w = 3 + 0.5x^2\) kN/m on a 4 m beam from "Average value of a function" has \(F_R = \int_0^4 w\,dx = \frac{68}{3} = 22.7\) kN, which is its average intensity times the length. Its location is
past the middle, because the load is heaviest near the right end. A load made of several pieces can be handled piece by piece, each with its own resultant.
Using resultants correctly
On a free-body diagram, draw either the distributed load or its resultant, never both, or the load is counted twice. A resultant replaces only the load it came from: loads on different parts of a beam each get their own. And a resultant is equivalent only externally. It gives the correct support reactions, but cutting the beam to find internal forces needs the actual distribution on each side of the cut, as the topic "Internal forces and sign conventions" will show. Design loads for floors, roofs, snow and wind come from building codes, which set values by use and location.
Common mistakes to avoid
First, placing a triangular resultant one third of the way from the zero end instead of two thirds. Second, using \(w_0L\) for a triangle and forgetting the half. Third, taking the peak intensity as the force, when intensity is per metre and must be multiplied by a length. Fourth, keeping both the load and its resultant on one free-body diagram. Fifth, using the resultant to find internal forces at a cut inside the loaded length. Sixth, mixing kN/m with metres and N in one equation.
Key takeaways
A distributed load has intensity \(w(x)\) in force per length, or per area for surfaces. Its resultant is \(F_R = \int w\,dx\), the area of the load diagram, acting at \(\bar{x} = \int xw\,dx / \int w\,dx\), the area's centroid. Uniform: \(w_0L\) at the middle. Triangular: \(\tfrac{1}{2}w_0L\) at two thirds from the zero end. Split trapezoids into rectangles and triangles. Use resultants for reactions, one per load, but not for internal forces.
Flashcards
Flashcard
Force per unit length: N/m, kN/m or lb/ft
Test your understanding
Question 1 of 5
A beam carries a uniform load of 5 kN/m along its full 8 m length. What is the resultant and where does it act?
Question 2 of 5
A load rises linearly from 0 at the left end to 30 lb/ft at the right end of a 9 ft beam. What is its resultant?
Question 3 of 5
A load rises linearly from 2 kN/m to 8 kN/m over a 3 m length. What is its resultant?
Question 4 of 5
A 4 m cantilever carries a uniform load of 2 kN/m along its length. What is the size of the moment reaction at the wall?
Question 5 of 5
Which statement about the resultant of a distributed load is correct?
