Statics › Section G · Centroids and centers of gravity › Topic G.8

Fluid statics

Water pushing on a dam, a gate or a tank wall is a distributed load that grows steadily with depth. Treat it exactly as the previous topic treated beam loads, and centroids give the size and position of the force.

Water as a distributed load

Dams, lock gates, retaining walls, tanks and pipes all hold back a fluid, and the fluid presses on every square centimetre of the surface it touches. That pressure is a distributed load. Unlike snow on a roof it is not uniform: it grows with depth, so the bottom of a wall is pushed far harder than the top. This topic finds the resultant of that load and where it acts, so that walls and gates can be checked with the equilibrium equations, for sliding open, tipping over or holding firm.

Pressure, gauge and absolute

Pressure is force per unit area, \(p = F/A\). In SI it is measured in pascals, \(1\ \mathrm{Pa} = 1\ \mathrm{N/m^2}\), usually as kPa. US customary units are psi (\(\mathrm{lb/in^2}\)), ksi (1000 psi) and psf (\(\mathrm{lb/ft^2}\)); since 1 ft² is 144 in², 1 psi is 144 psf, or about 6.89 kPa. Absolute pressure is measured from a perfect vacuum; gauge pressure is measured from the surrounding atmosphere, about 101.3 kPa or 14.7 psi. In most statics problems the atmosphere presses on both sides of a wall or gate and cancels, so this topic uses gauge pressure throughout, as most pressure gauges do.

Pressure grows with depth

In a liquid at rest, the gauge pressure at depth \(h\) below the free surface is

p = \rho g h = \gamma h

where \(\rho\) is the density and \(\gamma = \rho g\) is the specific weight, the weight per unit volume. For water, \(\rho = 1000\ \mathrm{kg/m^3}\) and \(g = 9.81\ \mathrm{m/s^2}\) give \(\gamma = 9810\ \mathrm{N/m^3}\) (statics uses 9.81; the physics and calculus topics round g to 9.80); in US units \(\gamma = 62.4\ \mathrm{lb/ft^3}\). At a point, pressure acts equally in all directions, and on any surface it pushes perpendicular to that surface. It depends only on depth, not on the shape or size of the container, as the physics topic "Pressure with depth, Pascal's principle, gauge pressure" showed. The formula assumes constant density, which suits liquids but not gases over large heights.

From pressure to a resultant force

On a vertical wall of width \(b\) into the page, a strip at depth \(y\) carries a line load \(w = \gamma y b\). Pressure is linear in depth, so the load diagram is a triangle if the wall starts at the surface and a trapezoid if it starts below. The resultant is the area of that diagram, which equals the average pressure times the wetted area, and for a flat plate that average is the pressure at the plate's centroid:

F = \gamma A \bar{d}

with \(\bar{d}\) the centroid's depth, as in the calculus topic "Fluid pressure and force". The line of action passes through the centroid of the pressure diagram, called the centre of pressure, which on a vertical or sloping plate lies below the plate's own centroid.

Worked example: a tank wall

A vertical wall holds back water 3.0 m deep. Find the force on each metre of wall and where it acts. 1. Pressure at the base: \(p = 9810 \times 3.0 = 29.4\) kPa. 2. Per metre of width the load diagram is a triangle from 0 at the surface to 29.4 kN/m at the base. 3. Resultant: \(F = \tfrac{1}{2}(29.43)(3.0) = 44.1\) kN per metre. 4. It acts at the triangle's centroid, one third of the depth up from the base: 1.0 m above the base, or 2.0 m below the surface. 5. Check with \(\gamma A \bar{d}\): \(9810 \times 3.0 \times 1.5 = 44.1\) kN. Doubling the depth would quadruple the force.

Worked example: a submerged gate

A vertical rectangular gate 1.2 m wide and 2.0 m tall has its top edge 1.5 m below the surface. 1. Pressures: 14.7 kPa at the top (1.5 m) and 34.3 kPa at the bottom (3.5 m). 2. Split the trapezoid: a rectangle of 14.7 kPa gives \(14.715 \times 2.4 = 35.3\) kN at 1.0 m below the top edge; a triangle rising to 19.6 kPa gives \(\tfrac{1}{2}(19.62)(2.4) = 23.5\) kN at 1.33 m below the top edge. 3. Total: \(F = 58.9\) kN. 4. Location below the top edge:

\frac{35.3(1.0) + 23.5(1.33)}{58.9} = 1.13\ \text{m}

a depth of 2.63 m. 5. Check: \(\gamma A \bar{d} = 9810 \times 2.4 \times 2.5 = 58.9\) kN, and the force acts below the centroid depth of 2.5 m, as it must.

Sloping and horizontal surfaces

On a sloping plate, pressure still depends on vertical depth, but it acts perpendicular to the plate, so the resultant is perpendicular too. A tank face 1.5 m wide and 2.0 m long down the slope, inclined at 60° to the horizontal with its top at the surface, has its bottom edge at a depth of \(2.0\sin 60^\circ = 1.73\) m, where the pressure is 17.0 kPa. The force is the average, 8.50 kPa, times 3.0 \(\mathrm{m^2}\): 25.5 kN, acting normal to the plate two thirds of the way down it. A horizontal surface sits at one depth, so its load is uniform: a tank floor 2.5 m down with area 6.0 \(\mathrm{m^2}\) carries \(24.5 \times 6.0 = 147\) kN. If the tank's walls are vertical, that equals the weight of the water above the floor; with sloping walls it does not.

Worked example: will the wall tip?

A rectangular concrete wall 2.0 m tall, of density 2400 \(\mathrm{kg/m^3}\), holds water to its full height. How thick must it be not to tip about its downstream toe? Assume no anchorage, no sliding and no water pressure under the base, and work per metre of length. 1. Water: \(F = \tfrac{1}{2}(9810)(2.0)^2 = 19{,}620\) N, acting 0.667 m above the base, so its overturning moment about the toe is 13,080 N·m. 2. Wall of thickness \(t\): weight \(2400 \times 9.81 \times 2.0t = 47{,}088t\) N, acting \(t/2\) from the toe. 3. No tipping requires \(47{,}088t \cdot \frac{t}{2} \ge 13{,}080\), so \(23{,}544t^2 \ge 13{,}080\) and \(t \ge 0.745\) m. 4. Check: at \(t = 0.745\) m both moments equal 13,080 N·m.

Common mistakes to avoid

First, measuring depth along a sloping surface instead of vertically. Second, adding atmospheric pressure when it acts on both sides and cancels. Third, placing the resultant at the plate's centroid; it acts at the centroid of the pressure diagram, lower down. Fourth, forgetting the width into the page, so that a force per metre is reported as a total. Fifth, pointing the force vertically on a sloping plate instead of perpendicular to it. Sixth, multiplying \(\gamma\) in \(\mathrm{lb/ft^3}\) by \(g\) again: specific weight already includes gravity.

Key takeaways

Gauge pressure in a liquid is \(p = \gamma h\), with \(h\) the vertical depth and \(\gamma = 9810\ \mathrm{N/m^3}\) or \(62.4\ \mathrm{lb/ft^3}\) for water. Pressure acts perpendicular to every surface and depends only on depth. On a flat plate it is a triangular or trapezoidal distributed load; the resultant is the area of the pressure diagram times the width, or \(\gamma A \bar{d}\), and it acts through the diagram's centroid, below the plate's centroid. A wall holding water to depth \(H\) takes \(\gamma H^2/2\) per unit width, at \(H/3\) above the base.

Flashcards

Flashcard

Pressure

p = F / A, in Pa = N/m²

Also kPa, psi, ksi and psf.

Test your understanding

Question 1 of 5

What is the gauge pressure 12 ft below the surface of fresh water, taking γ = 62.4 lb/ft³?

Question 2 of 5

A vertical wall holds back water 2.4 m deep. What is the water's force on each metre of wall, and where does it act?

Question 3 of 5

A vertical plate 1.0 m wide and 1.0 m tall is submerged with its top edge 2.0 m below the water surface. What is the water's force on one face?

Question 4 of 5

A plate 3.0 m long lies on a slope at 30° to the horizontal, with its top edge at the water surface. What is the gauge pressure at its bottom edge?

Question 5 of 5

In which direction does the resultant water force act on a flat plate that slopes at 45°?

← Previous topicNext topic →