Statics › Section A · Introduction to statics › Topic A.3

Forces and idealizations

Real forces spread over areas and real bodies bend, but statics gets accurate answers by replacing them with simpler models. Knowing the names of the forces you meet, and which simplifications are safe, is the first step in setting up any problem.

Many kinds of push and pull

A force is a push or a pull that one body exerts on another, either by contact, as when a jack lifts a car, or at a distance, as with gravity. As the topic "Newton's laws of motion" explained, every force has an equal and opposite partner on the other body. Forces arise in so many situations that engineers use a precise vocabulary for them. Some terms describe how a force is spread out, and others describe the job it does in a structure. Learning both sets of terms now will make every later problem statement easier to read.

Concentrated forces

A concentrated force, also called a point force, acts at a single point. Examples are the pull of a cable bolted to a bracket, the push of a jack under a car, or a wheel pressing on a bridge deck. Strictly, no real force acts at a mathematical point: the jack's pad, the bolt and the tyre all touch over a small area. But when that area is small compared with the body, treating the force as acting at one point gives accurate results and makes the arithmetic far simpler. Most forces in this course are drawn this way.

Distributed forces

A distributed force is spread over a line, an area or a volume. A partition wall standing on a floor beam loads it along a line, measured in newtons per metre (N/m). Wind on a sign or water against a dam acts over an area, measured as a pressure in pascals, N/m². Distributed forces are drawn as a row of small arrows whose lengths show the intensity. For calculation they are usually replaced by a single equivalent concentrated force. Finding its size and position exactly is the subject of the topic "Distributed loads"; for a uniform load, the equivalent force acts at the middle.

Body forces

A body force is distributed through the volume of a body, acting on every part of it at once. Weight is the most important example; electric and magnetic forces are body forces too, though statics rarely needs them. Buoyancy is sometimes listed with them, but it is really the net effect of fluid pressure on the body's surface. A body's weight is modelled as one force acting at its centre of gravity, explained in the topic "Center of gravity and center of mass". Weight is sometimes small enough to ignore. The rule in this course: include a body's weight whenever the problem gives enough information to find it, and otherwise treat it as negligible.

Loads, reactions, interactions and internal forces

Forces are also named by their role. Loads are the forces a body exists to carry, such as traffic on a bridge or snow on a roof. Reactions are the forces and moments that supports supply to hold the body in equilibrium; they adjust automatically, so a heavier load produces larger reactions. Interaction forces act between connected bodies, in equal and opposite pairs, and matter when structures have several parts. Internal forces act within the material of a body, resisting the loads so it does not break; they are described as an axial force, a shear force and a bending moment, studied in the topic "Internal forces and sign conventions".

Worked example: forces on a roadside sign

A rectangular sign, 1.2 m wide and 0.9 m tall with a mass of 25 kg, is bolted to the top of a steel post set in a concrete footing. A wind presses on its face at 0.6 kPa. Classify the forces. 1. The wind is a distributed load over an area. Its total is pressure times area: \(0.6 \times 1.2 \times 0.9 = 0.648\) kN, or 648 N. 2. The sign's weight, \(25 \times 9.81 = 245\) N, is a body force and also a load. 3. The footing supplies reactions at the base of the post: a force and a moment that resist the wind and the weight. 4. Inside the post, internal forces carry these effects down to the footing.

Idealised models

Statics replaces real objects with idealised models. A particle is a body whose size and shape do not matter, so every force on it acts through one point; a ring where cables meet is a good example. A rigid body keeps its shape and size under load. No material is truly rigid, but well-designed structures deform so little that the error is tiny. An ideal cable is weightless and does not stretch, and it can only pull along its own length. Smooth surfaces and frictionless pins exert no friction. Each model has a condition attached, and part of engineering judgement is checking that it holds.

Worked example: replacing a uniform load

A 4 m timber beam supports a partition wall that loads it uniformly at 0.3 kN/m along its whole length. Replace the wall's load by a single concentrated force. 1. The intensity is constant, so the total force is intensity times length: \(0.3 \times 4 = 1.2\) kN. 2. A uniform load is symmetric about the middle of its length, so the equivalent force acts at 2 m from either end. 3. Direction: downward, like the wall's weight. 4. Check the units: kN/m times m gives kN, a force, as it should. The beam can now be analysed with one 1.2 kN force at its centre.

Worked example: can the rope's weight be ignored?

A 500 kg engine block hangs from a hoist by a rope whose total mass is 2 kg. Is it reasonable to treat the rope as weightless? 1. Weight of the engine: \(500 \times 9.81 = 4905\) N. 2. Weight of the rope: \(2 \times 9.81 = 19.6\) N. 3. Compare them: \(\frac{19.6}{4905} = 0.004\), so the rope adds 0.4% to the load. 4. Loads are seldom known better than this, so the ideal-cable model is reasonable here. For a long, heavy cable carrying a light load, such as a power line, the same comparison would fail and the cable's weight would have to be included.

Common mistakes to avoid

First, forgetting that a concentrated force is a model: it is an approximation to a force spread over a small area. Second, replacing a distributed load by its total but putting that total in the wrong place. Third, treating reactions as fixed values; they depend on the loads. Fourth, quietly dropping a body's weight when the problem gives its mass. Fifth, using an idealisation without checking its condition, such as treating a long, heavy cable as weightless.

Key takeaways

Forces are pushes or pulls between bodies. A concentrated force acts at a point, a distributed force acts over a line (N/m) or an area (Pa), and a body force such as weight acts throughout a volume. By role, forces are loads, reactions from supports, interaction forces between parts, or internal forces within the material. Statics uses idealised models: particles, rigid bodies, concentrated forces, ideal cables and frictionless contacts. Each is accurate only when its condition holds, so compare sizes before you neglect anything.

Flashcards

Flashcard

Force

A push or pull exerted by one body on another

By contact or at a distance.

Test your understanding

Question 1 of 5

Which of these is a body force?

Question 2 of 5

A 6 m beam carries a uniform load of 0.5 kN/m along its whole length. What single force is equivalent?

Question 3 of 5

What are reactions?

Question 4 of 5

A 3 kg rope holds a 600 kg load. The rope's weight is what percentage of the load's weight?

Question 5 of 5

What does modelling a body as rigid assume?

← Previous topicNext topic →