Statics › Section A · Introduction to statics › Topic A.2
Units, mass, and weight
A beam that carries 20 is meaningless until you know whether that is 20 newtons, 20 kilonewtons or 20 pounds. Engineers in the United States work in two unit systems, so knowing which units you hold, and whether a number is a mass or a weight, prevents some of the costliest mistakes in the subject.
Every number needs a unit
An engineering quantity is a number multiplied by a unit, such as 75 kg, 2.4 m or 12 kN. Without the unit the number gives no information, so always write it, and expect almost every answer in statics to carry one; only ratios, such as a slope or a coefficient of friction, are dimensionless. Statics needs three base quantities: mass, length and time. Everything else is derived from them. Force, for example, is mass times acceleration, so its dimensions are mass times length divided by time squared. The physics topic "Units, significant figures, and estimation" covers base units, prefixes and significant figures in more depth.
The SI system
In SI units, length is in metres (m), mass in kilograms (kg) and time in seconds (s). The unit of force is the newton (N), defined as the force that gives 1 kg an acceleration of 1 m/s², so 1 N = 1 kg·m/s². Engineering loads are large, so prefixes are common: 1 kN = 1,000 N and 1 MN = 1,000,000 N, while dimensions are often in millimetres. Moments, met later in the course, are in newton-metres (N·m). Stresses are in pascals, 1 Pa = 1 N/m², and usually quoted in megapascals; conveniently, 1 MPa = 1 N/mm².
US customary units
US engineering practice mostly uses the British Gravitational system: length in feet (ft) or inches, time in seconds, force in pounds (lb, strictly lbf, pound-force) and mass in slugs. One pound-force gives one slug an acceleration of 1 ft/s², so 1 lb = 1 slug·ft/s². Large loads are given in kips: 1 kip = 1,000 lb. A second system, English Engineering, measures mass in pound-mass (lbm), where 32.174 lbm = 1 slug. By definition, 1 lbm weighs 1 lbf at standard gravity, which tempts people to treat mass and weight as the same thing. This course follows the usual rule: in statics, every pound is a force.
Mass and weight
Mass measures how much matter a body contains. It is a scalar and does not change from place to place. Weight is the gravitational force on that mass, a vector pointing towards Earth's centre:
This is Newton's second law applied to a falling body, with \(g\) as the acceleration due to gravity. Engineers use \(g = 9.81\) m/s² in SI units and \(g = 32.2\) ft/s² in US units, and this course uses those values throughout. The physics course uses 9.80 m/s². Real \(g\) varies from about 9.78 to 9.83 m/s² over Earth's surface, and the agreed standard value is 9.80665 m/s², so both choices are reasonable. Watch the habit of each system: SI problems usually give a mass, US problems usually give a weight.
Worked example: weight from mass
A 2.5 tonne generator (2,500 kg) is lifted by a crane, and a 75 kg technician stands on the platform beside it. Find each weight in SI units. 1. The masses are given, so multiply by \(g\). 2. Generator: \(W = 2500 \times 9.81 = 24{,}525\) N, which is 24.5 kN to three significant figures. 3. Technician: \(W = 75 \times 9.81 = 735.75\) N, about 736 N. 4. Check the sizes: each kilogram weighs just under 10 N, so 2,500 kg should weigh just under 25 kN, and it does. Quoting the generator as 2,500 N, or the technician as 75 N, would be a mass written as a force.
Worked example: mass from weight
A specification sheet lists a motor as 180 lb. Find its mass in slugs and in kilograms. 1. Pounds are a force, so 180 lb is the weight. 2. Rearrange \(W = mg\): \(m = \frac{W}{g} = \frac{180}{32.2} = 5.59\) slug. 3. For SI, first convert the weight with 1 lb = 4.448 N: \(W = 180 \times 4.448 = 800.6\) N. 4. Then \(m = \frac{800.6}{9.81} = 81.6\) kg. 5. Check by converting the slug answer directly, with 1 slug = 14.59 kg: \(5.59 \times 14.59 = 81.6\) kg. The two routes agree.
Converting units
To convert, multiply by a fraction whose top and bottom are equal quantities, so its value is 1, arranged so the unwanted unit cancels. For example,
which shows the two values of \(g\) describe the same acceleration. Useful factors: 1 ft = 0.3048 m and 1 in = 25.4 mm (both exact), 1 lb = 4.448 N, 1 slug = 14.59 kg and 1 kip = 1,000 lb. When a problem mixes systems, convert everything to one consistent set before you start.
Worked example: converting a moment
A bolt on a pump flange must be tightened to 1,200 lb·ft, but the available torque wrench reads in N·m. 1. A moment is a force times a length, so convert both parts. 2. Force factor: 1 lb = 4.448 N. Length factor: 1 ft = 0.3048 m. 3. Multiply:
4. Round to 1,630 N·m, or 1.63 kN·m. 5. Check: 1 lb·ft is about 1.36 N·m, and \(1200 \times 1.36 = 1632\), close to the exact result. Converting only the force, which gives 5,338, is a common slip; the units of the answer would be N·ft, not N·m.
Consistency and sense checks
Only add or subtract quantities with the same units, and make sure both sides of every equation have the same units. Use \(g = 9.81\) m/s² only with metres and kilograms, and 32.2 ft/s² only with feet and slugs. Give final answers to about three significant figures, because loads and dimensions are rarely known better than that, but keep extra digits in intermediate steps. Finally, build a feel for size: a newton is roughly the weight of a small apple, about 100 g of mass, and a slug is about 14.6 kg. A garden shed whose floor carries meganewtons is a sign that something has gone wrong.
Common mistakes to avoid
First, writing a mass in kilograms where a force in newtons belongs, or the reverse. Second, treating a US weight in pounds as a mass and multiplying it by 32.2. Third, using \(g = 9.81\) m/s² with feet, or 32.2 ft/s² with metres. Fourth, converting only part of a compound unit, such as the force in lb·ft but not the length. Fifth, dropping units from intermediate lines, which hides exactly these errors.
Key takeaways
Every quantity is a number with a unit. In SI units, force is in newtons, 1 N = 1 kg·m/s², with kN for typical loads. In US units, force is in pounds and mass in slugs, 1 lb = 1 slug·ft/s², with 1 kip = 1,000 lb; in statics, pounds are always forces. Weight is \(W = mg\), with \(g = 9.81\) m/s² or 32.2 ft/s². SI problems usually give mass and US problems usually give weight. Convert with factors equal to 1, keep units consistent, and report about three significant figures.
Flashcards
Flashcard
1 N = 1 kg·m/s²
Test your understanding
Question 1 of 5
Using g = 9.81 m/s², what is the weight of a 40 kg crate?
Question 2 of 5
A US drawing says a steel casting weighs 64.4 lb. What is its mass?
Question 3 of 5
Which statement about pounds follows the convention used in statics?
Question 4 of 5
A torque wrench is set to 50 lb·ft. Using 1 lb = 4.448 N and 1 ft = 0.3048 m, what is this in N·m?
Question 5 of 5
A student in an SI problem writes W = 12 kg × 32.2 ft/s². What is the error?
