Statics › Section F · Equilibrium of structures › Topic F.2

Interactions between members

Wherever two parts of a structure touch, they push or pull on each other with equal and opposite forces. Getting those pairs right on every free-body diagram is the single most important skill in analysing trusses, frames and machines.

Newton's third law at every connection

When one body acts on another, the second acts back on the first with a force of equal size in the opposite direction, along the same line. In a structure this happens at every pin, contact and weld. While the structure is in one piece, these action-reaction pairs are invisible: each pair lives inside the body and the two halves cancel. They appear only when you cut through a connection to draw a free-body diagram of one part, which exposes one half of each pair on that part. Those exposed forces are often exactly the unknowns you want.

Drawing pairs consistently

You may choose any direction for an unknown interaction force, but only once. If you draw the force of member 1 on member 2 at pin C as components \(C_x\) to the right and \(C_y\) upwards, then on member 1 you must draw \(C_x\) to the left and \(C_y\) downwards, with the same labels. The solved sign applies to both arrows at once: a negative \(C_x\) means both point the other way. Different letters for the two halves, or arrows in the same direction, silently break Newton's third law.

Exploding a truss

Picture a triangular truss pulled apart into three members and three pins. Member AB is in tension. The pins pull its ends outwards, away from each other, so the member stretches. By the third law the member pulls each pin back towards the middle of the member. So on a pin, a tension member's force points away from the pin, along the member; a compression member's force pushes into the pin. This is why the tension assumption is drawn as an arrow pulling away from the joint on a joint diagram. One label, such as \(F_{AB}\), names the member force and all four arrows that come from it.

Every part is in equilibrium

If a structure is in equilibrium, so is every piece of it: each member, each pin, each group of connected members and each section cut from it, right down to a small block of material inside a member. So you can draw a free-body boundary wherever it exposes the forces you need and few others. The whole structure gives the support reactions, a single member gives its pin forces, a joint gives its member forces, and a chunk of several members gives the forces in only the members you cut.

Internal and external depend on the boundary

A force is external to a free-body diagram when it crosses the boundary you drew, and internal when both bodies involved lie inside it. Only external forces go on the diagram. The pin force between two members is external on a diagram of either member alone, but internal, and therefore left off, on a diagram of both together, because its two halves cancel. A useful habit is to list what is included and what is excluded, then add one force for every interaction that crosses between the lists, and none that acts between two excluded bodies.

Pins as separate bodies

When three or more members meet at one pin, or a load hangs from the pin itself, decide where the pin belongs. Either treat it as part of one chosen member, so the load and the other members act on that member, or isolate the pin as its own small body acted on by every member and the load. Both are correct if done consistently. The second is cleaner when several members share the pin, because each member then interacts only with the pin. The method of joints does exactly this.

Worked example: a two-member arch

Member AC runs from a pin support at A(0, 0) to a pin C(3, 3), in metres. Member BC runs from a pin support at B(6, 0) to the same pin C. A 12 kN load hangs from the midpoint of AC at (1.5, 1.5); BC carries nothing else. 1. BC is a two-force member, so its force on AC acts along CB. Assume tension \(F\), pulling AC at C towards B, with components \(F/\sqrt{2}\) and \(-F/\sqrt{2}\). 2. Moments about A on AC, counterclockwise positive:

-\frac{6F}{\sqrt{2}} - 1.5(12) = 0

so \(F = -3\sqrt{2} \approx -4.24\) kN, a compression of 4.24 kN. 3. BC therefore pushes AC at C with (−3, 3) kN, and AC pushes BC with (3, −3) kN. 4. Balance of AC: \(A_x = 3\) kN and \(A_y = 9\) kN. Balance of BC: the support at B pushes with (−3, 3) kN. 5. Check the whole: horizontal forces 3 − 3 = 0, vertical 9 + 3 = 12 kN.

Worked example: a pulley on a bracket

A horizontal bracket is fixed to a wall at O(0, 0) and carries a frictionless pulley of radius 0.1 m on an axle pin at (0.5, 0), in metres. A rope tied to a wall hook at (0, 0.1) runs level to the top of the pulley, wraps a quarter turn over its upper-right quarter and hangs from its right side, at x = 0.6, to a 200 N weight. 1. Pulley alone: the rope pulls with (−200, 0) N and (0, −200) N, whose moments about the axle cancel, so the axle pushes the pulley with (200, 200) N, about 283 N at 45°. 2. Bracket alone: the pulley pushes the axle with (−200, −200) N, same label, arrows reversed. 3. The wall supplies (200, 200) N and a moment \(M_O\):

M_O + 0.5(-200) = 0

so \(M_O = 100\) N·m counterclockwise. 4. Check pulley and bracket together: the rope pulls give \(0.1(200) - 0.6(200) = -100\) N·m about O, again balanced.

Load paths

A load path is the route a force takes through connected members to reach the ground. Weight on a floor slab passes into the beams under it, the beams pass it to columns, and the columns deliver it to footings and the soil. Thinking in load paths tells you the order to solve things: start where forces are known, then move part by part along the path, using each solved interaction as a known force on the next part. A force with no path to a support signals a mistake in the model.

Common mistakes to avoid

First, drawing both halves of an action-reaction pair in the same direction, or giving them different names, on two connected diagrams. Second, putting an internal force on a diagram that contains both bodies involved. Third, adding a force that acts between two bodies outside your boundary, such as a floor reaction on a diagram that excludes the floor. Fourth, losing the sense of a solved force when carrying it to the next part: if member BC pushes on AC, then AC pushes on BC. Fifth, forgetting the load or reaction acting at a shared pin, or applying it to two members at once.

Key takeaways

Every connection carries equal and opposite action-reaction pairs, which appear only when a free-body diagram cuts through the connection. Choose a direction for each unknown pair once, draw the opposite on the other body with the same label, and let the solved sign apply to both. Every part of a structure in equilibrium is in equilibrium, so draw boundaries that expose the forces you need. A force is external only if it crosses your boundary. A shared pin can be isolated as its own body. Follow the load path from known forces to unknown ones.

Flashcards

Flashcard

Action-reaction pair

Equal, opposite, collinear forces two bodies exert on each other

Newton's third law.

Test your understanding

Question 1 of 5

On the diagram of member 1 you draw the force from member 2 at pin C as Cx to the left. How must you draw Cx on the diagram of member 2?

Question 2 of 5

A free-body diagram includes both members AC and BC of a frame, joined by the pin at C. Which forces at C belong on it?

Question 3 of 5

A frictionless pulley carries a rope with tension 200 N; one segment runs straight down and the other runs horizontally. What is the magnitude of the force the axle pin exerts on the pulley?

Question 4 of 5

In a two-member arch, member BC turns out to push member AC at pin C with components (−3, 3) kN. What force does AC exert on BC at C?

Question 5 of 5

Which statement about a structure in equilibrium is correct?

← Previous topicNext topic →