Statics › Section F · Equilibrium of structures › Topic F.1
Structures and two-force members
Bridges, cranes, pliers and ladders are all structures: several rigid bodies joined together. Before solving any of them, it pays to spot the members that carry force at only two points, because their force direction comes for free.
What counts as a structure
A structure is a set of connected rigid bodies built to do a job. Its parts may be fixed relative to each other, like the members of a roof, or able to move, like the blades of scissors. Solving a structure means finding every force acting on and between its parts. Each part obeys the same equilibrium equations as in 2D rigid body equilibrium; only the bookkeeping grows. The usual plan is to treat the whole structure as one body first, then take it apart and analyse the pieces.
Trusses, frames and machines
Engineers sort structures into three families, and the family decides the method. A truss is built from slender straight members joined at their ends into triangles, with loads applied only at the joints; every member carries a pure push or pull along its length, as in bridges, roofs and crane booms. A frame is a stationary structure that contains at least one multi-force member, one loaded at three or more points, so its members can bend. Building frames, bicycle frames and shelving are frames. A machine is like a frame but has moving parts and is designed to change an input force into a useful output force, as pliers and car jacks do.
Two-force members
A two-force member is a body acted on by forces at exactly two points, with no couples and no other loads; its own weight is neglected. You recognise one by counting connections: it is attached at two places and nothing else touches it. It need not be straight or slender. A hydraulic cylinder pinned at both ends, a cable, a short link and every member of an ideal truss are two-force members. A beam with a load hung from its middle is not, because that load is a third force.
Why the forces must be collinear
Call the two loaded points A and B. Force equilibrium makes the two forces equal and opposite. Now take moments about A. The force at A has no moment about A, so the force at B must have zero moment about A too: its line of action passes through A. The same argument from B shows the force at A passes through B. So both forces act along the straight line AB. The direction is known before you write an equation, and the member adds just one unknown, the magnitude.
Tension, compression and the sign convention
A two-force member is in tension when its end forces pull outwards and tend to stretch it, and in compression when they push inwards and tend to shorten it. This course uses one convention throughout: assume every unknown member force is tension, so on any free-body diagram it pulls away from the point it acts on. A positive answer is then tension and a negative answer compression. A curved two-force member still carries its force along the straight line joining its two pins, not along its curve. Because the curve sits off that line, the member also bends internally, so curved links are made deeper.
Three-force members
A body acted on by exactly three forces, with no couples, has a related property: the three lines of action must meet at one point or all be parallel. If two of them meet at a point P, both have zero moment about P, so the third must too, and its line passes through P. Knowing two directions therefore fixes the third. The three forces also form a closed triangle when drawn head to tail, because they sum to zero, and a sketch of that triangle makes a quick check.
Worked example: a strut-braced bracket
A horizontal beam AC, 2.4 m long, is pinned to a wall at A and carries 500 N at its free end C. A straight strut is pinned to the wall at D, 1.2 m directly below A, and to the beam at B, 1.6 m from A. Put A at the origin, x away from the wall, y up. 1. The strut touches only B and D, so it is a two-force member along DB, which is 2.0 m long with direction (0.8, 0.6). 2. Assume tension \(F\): it pulls the beam at B towards D, with components \(-0.8F\) and \(-0.6F\). 3. Moments about A, counterclockwise positive:
so \(F = -1250\) N, a compression of 1250 N. 4. Force balance gives \(A_x = -1000\) N and \(A_y = -250\) N. 5. Check: the beam is a three-force member. The strut and load lines meet at (2.4, 0.6), and the pin force, slope 0.25, passes through it.
Worked example: a ladder against a smooth wall
A uniform 5.0 m ladder weighing 300 N leans against a smooth wall. Its foot rests on rough ground 3.0 m from the wall, so the top touches the wall 4.0 m up. Put the foot at the origin. 1. Three forces act: the weight at the midpoint (1.5, 2.0), the wall's horizontal push at the top (the wall is smooth), and the ground force at the foot. 2. The weight line \(x = 1.5\) and the wall line \(y = 4.0\) meet at P(1.5, 4.0), so the ground force points from the foot towards P, with horizontal-to-vertical ratio 1.5 : 4.0. 3. Vertical balance gives a normal force of 300 N, so the friction needed is \(0.375 \times 300 = 112.5\) N towards the wall (the ground must be rough enough to supply it), and the wall pushes back with 112.5 N. 4. Check with moments about the foot: \(112.5 \times 4.0 = 450\) N·m and \(300 \times 1.5 = 450\) N·m. The ground force is about 320 N at 69.4° above the horizontal.
Spotting member types
Before writing equations, count the points where each part is loaded: pins, supports, cables, applied loads. Exactly two, with no couple and negligible weight, makes a two-force member. Exactly three, with no couple, makes a three-force member. Anything else is a general multi-force body with three equilibrium equations in 2D. Traps: a pulley mounted partway along a member adds a third load point, and a member whose weight matters is no longer two-force. Loads applied exactly at a pin do not count against it, because they act at one of its two points.
Common mistakes to avoid
First, drawing x and y components at both ends of a two-force member, which creates four unknowns where there is only one magnitude. Second, aligning a curved member's force with its curve or its tangent rather than with the straight line between its pins. Third, calling a member two-force when a load acts between its pins. Fourth, flipping a negative answer's arrow mid-problem and then counting the sign twice: keep the tension assumption and read the sign at the end. Fifth, forgetting that three forces may be parallel instead of concurrent.
Key takeaways
Solving a structure means finding every force on every part. Trusses have only two-force members loaded at joints, frames contain at least one multi-force member, and machines are frames with moving parts. A two-force member carries equal, opposite forces along the line joining its two load points, even if curved, so it adds one unknown. Assume tension: positive means tension, negative means compression. A three-force body's forces are concurrent or parallel, so two known lines fix the third and the forces close a triangle.
Flashcards
Flashcard
A set of connected rigid bodies designed to do a job
Test your understanding
Question 1 of 5
A straight link is pinned at both ends, has negligible weight and carries no other load. What can you say about the forces at its pins?
Question 2 of 5
Which of these is NOT a two-force member?
Question 3 of 5
Using the convention that every unknown member force is assumed to be tension, a member force comes out as −8.0 kN. What does this mean?
Question 4 of 5
A body is acted on by exactly three forces and no couples. Two of the lines of action meet at a point P. What must be true of the third force?
Question 5 of 5
A uniform ladder weighing 300 N leans on a smooth wall with its foot 3.0 m out and its top 4.0 m up. What is the horizontal force the wall exerts?
