Statics › Section F · Equilibrium of structures › Topic F.5

The method of sections

When you need the force in one member in the middle of a long truss, working joint by joint from the end is slow. The method of sections cuts straight to it: slice the truss, keep one piece, and often a single moment equation gives the answer.

Cut through the members you want

Imagine sawing a truss into two pieces along a line that passes through the members whose forces you need. Each piece is a rigid body in equilibrium, acted on by its own loads and reactions plus one force from every member you cut. Those member forces are still axial, because every truss member is a two-force member, so each cut adds only one unknown along a known line. Forces in members that were not cut stay internal and never appear, so you expose only the forces you are after.

Three equations, three unknowns

A piece of a planar truss is a rigid body, not a particle, so it gives three independent equations: \(\Sigma F_x = 0\), \(\Sigma F_y = 0\) and \(\Sigma M = 0\) about any point. You can therefore cut up to three members with unknown forces, as long as those three are not all concurrent or all parallel; otherwise the equations cannot separate them. The cut need not be straight, and it may also pass through members whose forces are already known.

The procedure

1. Confirm the structure is a simple truss. 2. Remove obvious zero-force members. 3. Find the support reactions, if any act on the piece you plan to keep. 4. Cut the truss into two pieces through the members you need, exposing no more than three unknowns. 5. Draw the simpler piece, with loads and reactions in their known directions and each cut member force drawn as tension, pulling away from the piece. 6. Solve the equilibrium equations; a negative answer means compression. 7. For other forces, make another cut or switch to the method of joints.

Choosing moment points

The skill lies in picking equations that contain one unknown each. Take moments about the point where the lines of two cut members intersect. Both of those forces pass through that point and drop out, leaving the third member alone in the equation. The intersection need not lie on the piece you kept, or even on the truss: any point is valid for a moment equation. When two cut members are parallel, as the top and bottom chords of a bridge truss often are, they never intersect, so use force balance perpendicular to them instead: \(\Sigma F_y = 0\) then isolates the diagonal.

Worked example: a Pratt bridge, the chords

A Pratt truss is 3 m deep and spans 24 m in six 4 m panels. Bottom joints L0 to L6 sit at x = 0, 4, ..., 24 m on y = 0; top joints U1 to U5 sit 3 m above L1 to L5. Members: bottom chord L0L1 to L5L6, top chord U1U2 to U4U5, end posts L0U1 and U5L6, verticals L1U1 to L5U5, and diagonals U1L2, U2L3, U4L3 and U5L4, sloping down towards midspan. A pin at L0, a roller at L6, 10 kN at each of L1 to L5. Find U2U3, U2L3 and L2L3. 1. By symmetry each reaction is 25 kN. 2. Cut through panel L2–L3; keep the left piece. 3. U2U3 and U2L3 meet at U2(8, 3), so moments about U2, counterclockwise positive, give

3F_{L2L3} - 25(8) + 10(4) = 0

and \(F_{L2L3} = 53.3\) kN (T). 4. U2L3 and L2L3 meet at L3(12, 0), off the left piece:

-3F_{U2U3} - 25(12) + 10(8) + 10(4) = 0

so \(F_{U2U3} = -60\) kN (C).

Worked example: a Pratt bridge, the diagonal

5. The chords U2U3 and L2L3 are parallel, so no moment point removes both. Use vertical balance instead. The diagonal runs from U2(8, 3) to L3(12, 0), 5 m long, so tension in it pulls the left piece with fractions (0.8, −0.6):

25 - 10 - 10 - 0.6F_{U2L3} = 0

giving \(F_{U2L3} = 8.33\) kN (T). This matches the Pratt pattern of tension diagonals. 6. Check with horizontal balance, unused so far: \(53.3 - 60 + 0.8(8.33) = 0\). Three forces in the middle of a 21-member truss took three equations and no joints, and a full matrix solution of every joint gives the same values.

Worked example: a roof truss with sloping chords

A roof truss has a pin at A(0, 0), a roller at E(12, 0), bottom joints B(3, 0), C(6, 0), D(9, 0) and top joints F(3, 1.5), G(6, 3), H(9, 1.5). Members: top chords AF, FG, GH, HE; bottom chord AB, BC, CD, DE; verticals BF, CG, DH; diagonals FC and HC. Each top joint carries 8 kN down, so each reaction is 12 kN. 1. Cut between B and C through FG, FC and BC; keep the piece A, B, F. 2. FG's line passes through A, and so does BC's, so moments about A isolate FC. FC has fractions (0.894, −0.447), and its moment arm works out to \(6/\sqrt{5} \approx 2.683\) m: \(-3(8) - 2.683F_{FC} = 0\), so \(F_{FC} = -8.94\) kN (C). 3. Moments about C, off the piece, isolate FG: \(F_{FG} = -17.9\) kN (C). 4. Moments about F give \(1.5F_{BC} - 3(12) = 0\), so \(F_{BC} = 24\) kN (T).

A truss behaves like a deep beam

For a simply supported truss under downward loads, the top chord is in compression and the bottom chord in tension, like the faces of a bending beam. At any cut, the two chords form an internal couple that balances the bending effect of the loads on one side, so roughly

\text{chord force} \approx \frac{M}{h}

where \(M\) is that bending effect about the cut and \(h\) is the truss depth. At the bridge's midspan, the 25 kN reaction and the loads 8 m and 4 m from the cut give \(M = 300 - 80 - 40 = 180\) kN·m, and \(180/3 = 60\) kN, the top chord force found above. Deepen the truss to 4 m and that force falls to 45 kN. Chord forces peak near midspan; diagonals carry the shear, which is largest near the supports.

Joints or sections?

Use the method of joints when you need every member force, and the method of sections when you need a few, especially deep inside a long truss. They mix freely: a cut can supply a known force that unlocks a joint. Getting the answers right matters for safety. The Quebec Bridge in Canada collapsed during construction in 1907, killing about 75 workers; the inquiry found that lower-chord compression members buckled, because they were inadequately designed and the bridge's own weight had been underestimated. Careful, checked analysis is part of an engineer's ethical duty.

Common mistakes to avoid

First, cutting through four or more members with unknown forces and then running out of equations. Second, cutting a truss into pieces that are not fully separated, so a member you forgot still connects them. Third, forgetting the support reaction on the piece you kept, or including a reaction that acts on the other piece. Fourth, refusing a moment point because it lies off the piece: any point works. Fifth, drawing a cut force in any direction other than along its own member.

Key takeaways

The method of sections cuts a truss into two pieces and applies three rigid-body equations to one of them, exposing only the cut members' forces. Cut no more than three unknown members, not all concurrent or parallel. Draw cut forces as tension; negative means compression. Take moments about the intersection of two cut members to isolate the third, even if that point lies off the piece; with parallel chords, use force balance across them for the diagonal. A simply supported truss acts like a deep beam, with chord forces roughly M/h, so deeper trusses have smaller chord forces.

Flashcards

Flashcard

Method of sections

Cut the truss and apply rigid-body equilibrium to one piece

Best for a few specific members.

Test your understanding

Question 1 of 5

What is the largest number of members with unknown forces you should cut in one section of a planar truss, and why?

Question 2 of 5

You cut three members. Two of them, if extended, meet at a point outside the piece you kept. Can you take moments about that point?

Question 3 of 5

A section through a bridge truss cuts the top chord, the bottom chord and one diagonal, and the two chords are parallel. Which equation isolates the diagonal?

Question 4 of 5

At a section of a simply supported truss 3 m deep, the bending effect of the loads on one side is 150 kN·m. Roughly what force does each chord carry?

Question 5 of 5

A simply supported Pratt bridge truss carries downward loads at its bottom joints. Which statement about its chords is correct?

← Previous topicNext topic →