Statics › Section J · Moments of inertia › Topic J.7

Products of inertia and mass moment of inertia

Two last ideas complete the course's picture of inertia. The product of inertia shows when an unsymmetrical section will bend at an angle, and the mass moment of inertia connects these flat-area tools to real spinning bodies.

When the axes are not enough

So far each moment of inertia has measured spread about one axis at a time. For a symmetrical I-beam that is the whole story. For an unsymmetrical section such as a steel angle, an L shape, it is not: load it straight down and it also bends sideways, because its stiffest and weakest directions are tilted. The product of inertia detects that tilt. The second half of this topic turns from areas to bodies. The mass moment of inertia, already met in physics, uses the same integral with mass in place of area, and for a thin plate the two are directly linked.

The product of inertia

The topic Integral properties of shapes defined

I_{xy} = \int_A xy\,dA

in units of length to the fourth power. Each piece of area contributes the product of its two coordinates, so its sign follows the quadrant: positive where \(x\) and \(y\) share a sign, in the first and third quadrants, and negative in the second and fourth. A whole shape's \(I_{xy}\) can therefore be positive, negative or zero. It depends on both axes together, and it changes if either axis moves or turns. Unlike \(I_x\) and \(I_y\), it says nothing about stiffness on its own; it describes how the area is arranged diagonally.

Symmetry makes it vanish

If the y axis is an axis of symmetry, every piece at \((x, y)\) has a twin at \((-x, y)\). Their products \(xy\) and \(-xy\) cancel, so \(I_{xy} = 0\). The same happens if the x axis is the axis of symmetry. One axis of symmetry is enough: a T-section about centroidal axes along and across its stem, or a semicircle about its symmetry line and any perpendicular axis, has zero product of inertia. A rectangle, a circle and an I-beam about their centroidal axes all give zero. A right triangle or an L-shaped angle has no axis of symmetry parallel to its legs, so its centroidal \(I_{xy}\) is not zero.

Moving the axes

The product of inertia has its own parallel axis theorem:

I_{xy} = \bar{I}_{x'y'} + A\bar{x}\bar{y}

Here \(\bar{I}_{x'y'}\) is about centroidal axes parallel to x and y, and \(\bar{x}\), \(\bar{y}\) are the coordinates of the centroid measured from the new axes, with their signs. That is the key difference from \(I = \bar{I} + Ad^2\): the transfer term \(A\bar{x}\bar{y}\) can be negative, so the centroidal value is not a minimum. For a composite section, sum \(\bar{I}_{x'y'} + A\bar{x}\bar{y}\) over the parts, using each part's own centroid coordinates, exactly as in the composite table.

Worked example: a rectangle and a triangle

1. A rectangle \(b\) wide and \(h\) tall sits with one corner at the origin, in the first quadrant. Its centroidal axes are lines of symmetry, so \(\bar{I}_{x'y'} = 0\), and

I_{xy} = 0 + bh\left(\frac{b}{2}\right)\left(\frac{h}{2}\right) = \frac{b^2h^2}{4}

For the 60 mm by 40 mm plate of the first topic that is \(1.44 \times 10^6\ \mathrm{mm^4}\), the value found there by direct integration. 2. A right triangle with its legs along the positive axes has, by integration, \(I_{xy} = b^2h^2/24\). Its centroid is at \((b/3, h/3)\), so backwards:

\bar{I}_{x'y'} = \frac{b^2h^2}{24} - \frac{bh}{2}\cdot\frac{b}{3}\cdot\frac{h}{3} = -\frac{b^2h^2}{72}

Check: the negative sign is possible here, and expected, because the hypotenuse leaves more area up-left and down-right of the centroid.

Principal axes

Turning the axes about a point changes \(I_x\), \(I_y\) and \(I_{xy}\), but at one angle \(\theta_p\) the product becomes zero. Those directions are the principal axes, and about them the moments of inertia take their largest and smallest values:

I_{\max,\min} = \frac{I_x + I_y}{2} \pm \sqrt{\left(\frac{I_x - I_y}{2}\right)^2 + I_{xy}^2}

with \(\tan 2\theta_p = -2I_{xy}/(I_x - I_y)\), measuring \(\theta_p\) anticlockwise from the x axis. An axis of symmetry is always a principal axis. A beam loaded along a principal direction deflects in that direction only; loaded at an angle to it, an angle section also deflects sideways.

Worked example: an angle section

An L-shaped angle has a vertical leg 10 mm wide and 100 mm tall, with a horizontal leg 65 mm long and 10 mm thick joined to the foot of its right side, so the angle is 75 mm wide overall. Its outer corner is at the origin. 1. Centroid: \(A = 1650\ \mathrm{mm^2}\), \(\bar{x} = 19.77\) mm, \(\bar{y} = 32.27\) mm. 2. Composite tables give \(\bar{I}_x = 1.636 \times 10^6\) and \(\bar{I}_y = 0.791 \times 10^6\ \mathrm{mm^4}\). 3. Each leg is a rectangle, so only transfer terms count:

\bar{I}_{xy} = 1000(-14.77)(17.73) + 650(22.73)(-27.27) = -0.665 \times 10^6\ \mathrm{mm^4}

4. Principal values:

I_{\max} = 2.00 \times 10^6,\quad I_{\min} = 0.426 \times 10^6\ \mathrm{mm^4}

with the axis of \(I_{\max}\) at \(\theta_p = 28.8^\circ\). Check: \(I_{\max} + I_{\min} = \bar{I}_x + \bar{I}_y\), since \(J\) cannot change.

The mass moment of inertia

The topic Rotational dynamics and moment of inertia used \(I = \sum mr^2\) and \(\tau = I\alpha\). In integral form,

I = \int r^2\,dm

where \(r\) is each element's distance from the axis, measured through a three-dimensional body. Its units are kg·m², not \(\mathrm{m^4}\). It has the same toolkit as area moments: a parallel axis theorem \(I = I_G + md^2\) about the centre of mass \(G\), a radius of gyration \(k = \sqrt{I/m}\), and composite bodies built part by part. It belongs to bodies that rotate, so it is used throughout the study of dynamics.

Worked example: a thin steel plate

For a uniform thin plate of density \(\rho\) and thickness \(t\), each piece of area has mass \(dm = \rho t\,dA\), so mass moments are area moments times \(\rho t\). A steel plate is 400 mm by 200 mm by 10 mm, with \(\rho = 7850\ \mathrm{kg/m^3}\). Find its mass moment of inertia about an axis through its centre, perpendicular to the plate. 1. \(\rho t = 7850 \times 0.010 = 78.5\ \mathrm{kg/m^2}\), so \(m = 78.5 \times 0.08 = 6.28\) kg and its weight is \(6.28 \times 9.81 = 61.6\) N. 2. In metres,

J = \frac{0.08(0.4^2 + 0.2^2)}{12} = 1.333 \times 10^{-3}\ \mathrm{m^4}

3. \(I = \rho tJ = 0.105\ \mathrm{kg\,m^2}\). Check with the plate formula from dynamics tables:

\frac{m(a^2 + b^2)}{12} = \frac{6.28(0.20)}{12} = 0.105\ \mathrm{kg\,m^2}

Common mistakes to avoid

First, assuming \(I_{xy}\) must be positive like \(I_x\); it takes the sign of the quadrants holding most of the area. Second, dropping the signs of \(\bar{x}\) and \(\bar{y}\) in \(A\bar{x}\bar{y}\). Third, thinking a shape needs two axes of symmetry for \(I_{xy} = 0\); one is enough. Fourth, treating the horizontal and vertical axes of an angle as principal; they are tilted. Fifth, mixing area moments in \(\mathrm{m^4}\) with mass moments in kg·m²: convert with \(\rho t\) for a thin plate, and work in metres before multiplying by a density.

Key takeaways

The product of inertia Ixy = ∫xy dA, in length to the fourth power, can be positive, negative or zero, and it is zero whenever either axis is an axis of symmetry. Its parallel axis theorem is Ixy = Īx′y′ + A x̄ ȳ, with signed centroid coordinates. A rectangle with a corner at the origin has b²h²/4; a right triangle's centroidal value is −b²h²/72. Principal axes have Ixy = 0 and carry the largest and smallest I. The mass moment of inertia I = ∫r² dm, in kg·m², has its own parallel axis theorem I = I_G + md². For a thin uniform plate, mass moment = ρt × area moment.

Flashcards

Flashcard

Ixy = ∫ xy dA

Product of inertia of an area, in length to the fourth power

Can be positive, negative or zero.

Test your understanding

Question 1 of 5

A rectangle 60 mm wide and 40 mm tall lies entirely in the second quadrant, with one corner at the origin. What is its product of inertia Ixy about the x and y axes?

Question 2 of 5

Which shape has a zero product of inertia about its horizontal and vertical centroidal axes?

Question 3 of 5

A shape has area 1200 mm², centroidal product of inertia 50,000 mm⁴, and centroid at x̄ = −20 mm, ȳ = 15 mm from a pair of parallel axes. What is Ixy about those axes?

Question 4 of 5

A section has Ix = 5.0 × 10⁶ mm⁴, Iy = 3.0 × 10⁶ mm⁴ and Ixy = 0 about its centroidal axes. What are its principal moments of inertia?

Question 5 of 5

A uniform aluminium plate 2.0 mm thick (ρ = 2700 kg/m³) has an area moment of inertia of 4.0 × 10⁻⁵ m⁴ about an axis in its plane. What is its mass moment of inertia about that axis?

← Previous topic