Statics › Section J · Moments of inertia › Topic J.6
Radius of gyration
A moment of inertia in mm⁴ is hard to picture. The radius of gyration turns it back into an ordinary distance, and that distance decides which way a column will buckle and how much load it can take.
A distance instead of a fourth power
Two sections can have the same moment of inertia while one uses far more material than the other, and a value like \(5.67 \times 10^6\ \mathrm{mm^4}\) says nothing directly about shape. The radius of gyration fixes both problems. It divides out the area and takes a square root, leaving a length that tells you how far from the axis the area is spread, on average in a squared sense. Engineers use it constantly in column design, and the same idea, with mass in place of area, describes rotating machine parts. This topic defines it, finds it for common shapes and shows why columns depend on it.
The definition
The radius of gyration about an axis is the distance at which the whole area, gathered into a thin strip parallel to that axis, would give the same moment of inertia. Since that strip would have \(I = Ak^2\),
Like a moment of inertia, \(k\) always belongs to a stated axis or point, and its units are plain length, such as millimetres. Turned around, \(I = Ak^2\), which is a handy way to recover a moment of inertia from a published radius of gyration.
Three radii, one relation
Divide \(J_O = I_x + I_y\), from the topic Polar moment of inertia, through by the area. Each term becomes a squared radius of gyration:
So the polar radius of gyration is the hypotenuse of a right triangle whose legs are the two rectangular ones. The radii themselves do not add: \(k_O\) is never \(k_x + k_y\). The same care applies to composite sections. You cannot add the parts' radii of gyration; add their moments of inertia and their areas first, as in the topic Moments of inertia of composite shapes, then take \(k = \sqrt{I/A}\) for the whole section.
Common shapes
For a rectangle of depth \(h\), \(\bar{I} = bh^3/12\) and \(A = bh\), so the width cancels:
A solid circle of radius \(r\) has \(\bar{k} = \sqrt{(\pi r^4/4)/(\pi r^2)} = r/2\) about any diameter. A tube gives
which grows towards \(r_o/\sqrt{2}\) as the wall gets thinner. Notice that \(k\) is never the distance to the centroid. For the rectangle, the centroidal \(k\) is \(0.289h\), not zero, because area lies on both sides of the axis.
Worked example: a rectangular bar
A bar has a rectangular cross-section 100 mm wide and 40 mm deep. Find its radii of gyration about the centroidal horizontal axis, the centroidal vertical axis and the centroid. 1. About the horizontal axis the depth is 40 mm: \(\bar{k}_x = 40/\sqrt{12} = 11.55\) mm. 2. About the vertical axis the 100 mm side is across the axis: \(\bar{k}_y = 100/\sqrt{12} = 28.87\) mm. 3. Polar:
4. Check with the polar moment: \(J_C = bh(b^2 + h^2)/12\), which is \(3.867 \times 10^6\ \mathrm{mm^4}\), and \(\sqrt{3.867 \times 10^6 / 4000} = 31.09\) mm. The bar is two and a half times wider than it is deep, and \(\bar{k}_y\) is two and a half times \(\bar{k}_x\).
Moving the axis
Divide the parallel axis theorem \(I = \bar{I} + Ad^2\) by the area and it becomes
where \(\bar{k}\) is about the centroidal axis and \(d\) is the distance between the parallel axes. Squared radii add like the sides of a right triangle again. For the 40 mm deep bar above, the radius of gyration about its bottom edge is \(\sqrt{11.55^2 + 20^2} = 23.09\) mm, which matches \(\sqrt{(bh^3/3)/(bh)} = h/\sqrt{3}\). Because \(\bar{k}^2\) is positive, \(k\) about any off-centre axis is always larger than the distance \(d\) from the centroid.
Why columns care
A slender column under compression fails by buckling: it suddenly bows sideways. In Mechanics of Materials you will meet Euler's formula for the buckling load of a column with pinned ends, \(P_{cr} = \pi^2 EI/L^2\), where \(E\) is the material's modulus of elasticity and \(L\) the length. Writing \(I = Ak^2\) gives
The ratio \(L/k\) is the slenderness ratio, and a larger value means a weaker column. A column bows about the axis with the smallest \(k\), so the 100 mm by 40 mm bar would buckle across its 40 mm depth. For the T-section of the composite topic, \(\bar{k}_x = 35.9\) mm but \(\bar{k}_y = 25.9\) mm, so it would bow sideways about its vertical axis.
Worked example: square bar or tube
A 2.00 m column could be a solid square bar 40 mm by 40 mm or a round tube of outer radius 30 mm with the same area, 1600 mm². Compare their slenderness ratios. 1. Tube's inner radius: \(\pi(30^2 - r_i^2) = 1600\) gives \(r_i = 19.77\) mm. 2. Square bar: \(k = 40/\sqrt{12} = 11.55\) mm, so \(L/k = 2000/11.55 = 173\). 3. Tube:
so \(L/k = 111\). 4. Euler's load goes as \(k^2\) for equal area and length, so the tube carries about \((17.96/11.55)^2 = 2.42\) times the buckling load. That is why scaffolding and many columns are tubes.
Mass radius of gyration
Rotating parts use the same idea with mass. The topic Rotational dynamics and moment of inertia in physics wrote \(I = \sum mr^2\) in kg·m²; the mass radius of gyration is \(k = \sqrt{I/m}\), in metres, so \(I = mk^2\). Manufacturers of flywheels, pulleys and rotors often quote \(k\) instead of \(I\). A 50 kg flywheel with \(k = 0.30\) m has \(I = 50(0.30)^2 = 4.5\ \mathrm{kg\,m^2}\). It behaves like all 50 kg concentrated on a thin ring of radius 0.30 m. Keep the two versions apart: area \(k\) comes from mm⁴ and mm², mass \(k\) from kg·m² and kg.
Common mistakes to avoid
First, forgetting the square root: \(I/A\) is \(k^2\), with units of length squared. Second, treating \(k\) as the distance to the centroid; a centroidal radius of gyration is not zero. Third, adding radii of gyration directly, either as \(k_O = k_x + k_y\) or across the parts of a composite section; add squares, or add \(I\) and \(A\) first. Fourth, checking a column only about its stronger axis; it buckles about the one with the smaller \(k\). Fifth, using \(k = d\) after moving an axis instead of \(k^2 = \bar{k}^2 + d^2\).
Key takeaways
The radius of gyration k = √(I/A) is the distance at which the whole area, as a thin strip, gives the same I; so I = Ak². It is a length and belongs to a stated axis. The polar version satisfies kO² = kx² + ky², and moving an axis gives k² = k̄² + d². A rectangle has k̄ = h/√12 ≈ 0.289h, a solid circle r/2 and a tube √(ro² + ri²)/2. Columns buckle about the axis with the least k, and the slenderness ratio L/k controls the buckling load. The mass version k = √(I/m) describes rotating parts, with I = mk² in kg·m².
Flashcards
Flashcard
Radius of gyration of an area about an axis
Test your understanding
Question 1 of 5
A section has I = 2.0 × 10⁶ mm⁴ about an axis and an area of 5000 mm². What is its radius of gyration about that axis?
Question 2 of 5
A rectangular bar is 50 mm wide and 120 mm deep. What is its radius of gyration about the centroidal horizontal axis?
Question 3 of 5
A section has kx = 30 mm and ky = 40 mm about perpendicular axes through point O. What is its polar radius of gyration about O?
Question 4 of 5
A pinned column has a solid rectangular cross-section 100 mm by 40 mm. About which centroidal axis will it buckle?
Question 5 of 5
A shape has a centroidal radius of gyration of 12 mm about a horizontal axis. What is its radius of gyration about a parallel axis 16 mm from the centroid?
