Statics › Section F · Equilibrium of structures › Topic F.8

Levers, pulleys, and simple machines

Six simple machines, the lever, the wheel and axle, the pulley, the inclined plane, the wedge and the screw, sit inside almost every mechanical device. Each one trades distance for force, and statics gives the exact exchange rate.

Six simple machines

Builders have long used six basic devices to move loads too heavy to lift directly: the lever, the wheel and axle, the pulley, the inclined plane, the wedge and the screw. Each obeys the rule from Machines and mechanical advantage: ignoring friction, work in equals work out, so a smaller effort moves through a larger distance. Each has an ideal mechanical advantage set only by its geometry. In this topic every MA is ideal, meaning frictionless.

The lever and its law

A lever is a rigid bar that turns about a fixed pivot called the fulcrum. Moments about the fulcrum, with the effort and load each perpendicular to the bar, give the law of the lever:

F_e\,a_e = F_l\,a_l

where \(a_e\) is the effort arm and \(a_l\) the load arm, each measured from the fulcrum. The mechanical advantage is therefore \(a_e / a_l\). Archimedes gave the earliest surviving proof of the law, in the third century BC. If a force is not perpendicular to the bar, use its perpendicular distance from the fulcrum instead.

Three classes of lever

Levers are classed by what sits in the middle. In a first-class lever the fulcrum lies between effort and load, as in a seesaw, a crowbar or a pair of scissors; its MA can be above or below 1. In a second-class lever the load lies between fulcrum and effort, as in a wheelbarrow or a nutcracker; the effort arm is always the longer, so the MA is always above 1. In a third-class lever the effort lies between fulcrum and load, as in tweezers, a fishing rod or your forearm; the MA is always below 1, but the load moves faster and further than the effort.

Worked example: a crowbar

A builder lifts one edge of a stone slab with a straight 1.5 m crowbar. The bar rests on a block, the fulcrum, 0.10 m from the end tucked under the slab, which presses down on that end with 1,800 N. The builder pushes down at the far end, perpendicular to the bar. 1. This is a first-class lever: the fulcrum sits between load and effort. 2. Arms: \(a_l = 0.10\) m and \(a_e = 1.5 - 0.10 = 1.40\) m. 3. MA \(= 1.40 / 0.10 = 14\). 4. Effort: \(1800 / 14 \approx 129\) N, about the weight of a 13 kg mass. 5. Check: \(1800 \times 0.10 = 180\) N·m balances \(128.6 \times 1.40\). The price: to raise the slab's edge 1 cm, the hand moves about 14 cm.

Worked example: the forearm

Hold a 40 N weight in your hand with your forearm horizontal. Model the forearm as a bar pivoting at the elbow. The biceps attaches 5 cm from the elbow and pulls straight up; the weight hangs 30 cm from the elbow. Neglect the forearm's own weight. 1. The effort, the biceps, lies between fulcrum and load, so this is a third-class lever. 2. Moments about the elbow: \(F_b(0.05) = 40(0.30)\), so \(F_b = 240\) N. 3. MA \(= 40 / 240 = 1/6\). 4. Vertical balance on the forearm: \(240 - 40 = 200\) N, so the upper arm bone presses down on the forearm at the elbow with 200 N. Muscles pull with several times the load they hold, and in return a small contraction swings the hand through a large arc.

Wheel and axle

A wheel and axle is a large wheel or crank fixed to a smaller drum, acting like a lever that never runs out of travel. With the effort applied at radius \(R\) and the load at radius \(r\), moments about the axle give an ideal MA of \(R / r\). A winch with a 0.40 m crank and a 0.10 m drum has an MA of 4, so a 2,000 N bucket of concrete needs a 500 N push on the handle, and the hand travels four times as far as the rope winds in. Screwdrivers, door handles, steering wheels and taps all work this way.

Pulleys

A single fixed pulley only changes the direction of a rope's pull: with a frictionless pulley the tension is the same on both sides, so the MA is 1. Its value is convenience, letting you pull down to lift up. A block and tackle combines a fixed block with a moving block attached to the load. Draw a free-body diagram of the moving block: every rope segment supporting it carries the same tension T, so with n supporting segments, \(nT = W\). The ideal MA is therefore n, the number of rope segments holding up the moving block, counting the free end if it leaves from that block. The rope end must be pulled n metres for every metre the load rises.

Worked example: lifting an engine

A mechanic lifts a 150 kg engine with a block and tackle in which four rope segments support the moving block. The pulleys are frictionless and their weight is neglected. 1. Weight: \(W = 150 \times 9.81 = 1471.5\) N. 2. Free-body diagram of the moving block: four upward tensions balance the weight, \(4T = 1471.5\). 3. So \(T \approx 368\) N, the force on the free end of the rope. 4. Ideal MA \(= W/T = 4\), equal to the segment count. 5. To raise the engine 1.0 m, each supporting segment shortens by 1.0 m, so the mechanic pulls 4.0 m of rope: about 1.47 kJ of work in and out.

Inclined planes, wedges and screws

A ramp of length L rising a height h lets you push a load up instead of lifting it. Pushing parallel to a frictionless slope, the force needed is \(W h / L\), so the ideal MA is \(L / h\): a 600 N cart on a 5 m ramp rising 1 m needs 120 N. A wedge is an inclined plane driven under or into a load, as in an axe or a door stop; friction dominates its behaviour, so it has its own topic, Wedges. A screw is an inclined plane wrapped round a cylinder. One turn of a handle of radius R advances it by its pitch p, so its ideal MA is \(2\pi R / p\). A jack with a 0.35 m handle and 5 mm pitch has an ideal MA of about 440.

Common mistakes to avoid

First, measuring lever arms from the end of the bar instead of from the fulcrum. Second, using the slanted distance to a force that is not perpendicular to the lever, instead of its perpendicular distance. Third, counting every rope segment in a block and tackle, including ones that do not support the moving block. Fourth, forgetting the pivot force: a forearm holding 40 N carries 200 N at the elbow. Fifth, quoting a screw's ideal MA as the real one: a jack with an ideal MA of 440 and 30% efficiency needs about 61 N, not 18 N, to lift 8 kN.

Key takeaways

All six simple machines trade distance for force. A lever's MA is effort arm over load arm, measured from the fulcrum. First-class levers have the fulcrum in the middle, second-class the load (MA above 1), third-class the effort (MA below 1, more speed and range). Wheel and axle: MA = R/r. Block and tackle: MA = the number of segments supporting the moving block. Inclined plane: MA = L/h for a push along the slope. Screw: MA = 2πR/p. Real machines deliver less because of friction.

Flashcards

Flashcard

Six simple machines

Lever, wheel and axle, pulley, inclined plane, wedge, screw

Each trades distance for force.

Test your understanding

Question 1 of 5

A wheelbarrow has its wheel axle as the fulcrum, the load centred 0.4 m from it and the handles 1.2 m from it. What class of lever is it, and what is its ideal MA?

Question 2 of 5

A forearm is held horizontal. The biceps pulls up 4 cm from the elbow and the hand holds 50 N at 32 cm from the elbow. Neglecting the forearm's weight, what is the biceps force?

Question 3 of 5

In a frictionless block and tackle, five rope segments support the moving block, which carries a 2,000 N load. What pull is needed on the free end of the rope?

Question 4 of 5

A winch has a crank of radius 0.30 m turning a drum of radius 0.06 m. What is its ideal mechanical advantage?

Question 5 of 5

A screw jack has a handle of radius 0.25 m and a thread pitch of 4 mm. What is its ideal mechanical advantage, to the nearest whole number?

← Previous topicNext topic →