Statics › Section F · Equilibrium of structures › Topic F.7
Machines and mechanical advantage
Pliers, bolt cutters, toggle clamps and car jacks turn a modest push from your hand into a large force where it is needed. Statics tells you exactly how large, by treating the machine as a frame caught at an instant of equilibrium.
What a machine is
A machine is a structure with parts that move relative to one another, built to take an input force and deliver a different output force. Pliers, scissors, bolt cutters, car jacks, vehicle suspensions and excavator arms are all machines. Statics analyses a machine at an instant when it is in equilibrium: holding a load, gripping an object, or moving so slowly that accelerations are negligible. At that instant the machine is analysed exactly like a frame. You take it apart at its pins, draw a free-body diagram of each member, use two-force members to fix directions, and keep every action-reaction pair equal and opposite.
Mechanical advantage
The mechanical advantage of a machine is the ratio of the output force it delivers to the input force you apply:
A tool with an MA of 4 turns a 50 N squeeze into a 200 N grip. The ideal mechanical advantage is the value calculated with friction ignored, as statics with smooth pins gives it. The actual mechanical advantage, measured on a real machine, is always lower, because friction at pins, threads and contacts absorbs part of the effort. An MA below 1 is not a failure: some machines deliberately give up force to gain speed or range of movement.
Finding the output force
The method is a chain of free-body diagrams. Start with the member that carries the known input force. Look for an equation containing only one unknown, usually moments about a pivot pin, which removes that pin's two unknown components. That gives the force passed to the next member. Carry it across the connection with the correct sense, by Newton's third law, and repeat until you reach the member that delivers the output. You need only the chain linking input to output, though pin forces matter for design, because pins must be sized to carry them.
Worked example: pliers in US customary units
A pair of pliers has two identical members crossing at a pivot pin. Each handle is squeezed with 30 lb at 4.0 in from the pin, and the jaws grip a bolt 1.0 in from the pin on the other side. Find the grip force, the MA and the pin force. 1. Take one member. The hand pushes its handle towards the other handle, and the bolt pushes back on its jaw. 2. Moments about the pin remove the pin force:
so \(F_{\text{grip}} = 120\) lb, about 534 N. 3. MA = 120 / 30 = 4. 4. The hand force and the bolt force lie on opposite sides of the pin, so for their moments to cancel they point the same way. The pin must balance both: \(30 + 120 = 150\) lb. The pin carries more than either the input or the output.
Force trades for distance
A machine cannot create energy. If friction is ignored, the work you put in equals the work it delivers:
so the ideal MA also equals the ratio of the distances moved, \(d_{\text{in}}/d_{\text{out}}\). In the pliers, the jaws move only a quarter as far as your hands. That is the price of quadrupling the force. It also gives a second way to find an ideal MA: move the input slightly and see how far the output moves, an idea known as the principle of virtual work.
Efficiency
Efficiency \(\eta\) is the useful work a machine delivers divided by the work put in. Friction always makes it less than 100%. Because the distances moved are fixed by the geometry, efficiency also links the two kinds of MA:
A jack with an ideal MA of 120 and an efficiency of 40% has an actual MA of 48, so lifting 6,000 N takes 125 N of effort rather than the ideal 50 N. Bearings, lubrication and careful geometry keep efficiency high. In this course's statics problems, pins are smooth, so the answers are ideal values.
Compound machines and toggles
When the output of one stage drives the input of the next, the mechanical advantages multiply. Bolt cutters link a pair of long handles to a pair of short jaws: if the handle stage multiplies force by 5 and the jaw stage by 8, the overall MA is 40, and a 250 N squeeze gives 10 kN at the blades. A toggle is a linkage of two links meeting at a knee. Push the knee towards the straight-line position and the links drive their ends apart with a force that grows without limit as the links straighten. Toggle clamps, stone crushers and some presses use this effect to produce very large forces from a small push.
Worked example: a toggle press
Two equal links AB and BC meet at a knee pin B. A is a fixed pin; C is pinned to a slider that runs in a smooth horizontal guide and presses on a workpiece. Both links make an angle \(\theta\) with the horizontal line AC, with B above it, and a downward force P = 200 N acts on the knee. 1. Both links are two-force members. At the knee, each pushes up along its own line with force F, so vertical balance gives \(2F\sin\theta = P\). 2. At the slider, the link's horizontal component is the pressing force:
3. At \(\theta = 10°\): F = 575.9 N in each link and \(F_{\text{out}} = 567.1\) N, an MA of 2.84. 4. At \(\theta = 5°\): \(F_{\text{out}} = 1143\) N, an MA of 5.72. Halving the angle roughly doubles the force; in practice friction and the links' flexing set the limit.
Self-locking machines
Some machines hold their load with no input force at all, because friction is large enough to stop the load driving the machine backwards. Most screw jacks and worm gears behave this way, which is exactly what you want when a car is raised above you: let go of the handle and it stays put. The cost is efficiency. A self-locking screw must lose so much to friction that its efficiency is generally below 50%. The friction calculations behind this appear in the Screw threads topic; here it is enough to know that safety and efficiency pull in opposite directions.
Common mistakes to avoid
First, forgetting the pin force, or assuming it equals the input or output. In the pliers it is 150 lb, more than either. Second, writing moments about a point where the unknowns do not drop out, when the pivot pin would remove two of them at once. Third, multiplying the MAs of stages that are not in series. Fourth, quoting an ideal MA as if it were what a real tool delivers; multiply by the efficiency. Fifth, forgetting that a large force always comes with a small movement: no linkage gives both more force and more distance.
Key takeaways
A machine is a frame with moving parts, analysed at an instant of equilibrium using the frame method. Mechanical advantage is output force over input force; ideal MA ignores friction and actual MA is lower. Find the output by a chain of free-body diagrams, usually with moments about pivots. Ignoring friction, input work equals output work, so ideal MA equals the ratio of distances moved. Actual MA = efficiency × ideal MA. Stages in series multiply their MAs. A toggle's output, P/(2 tan θ), grows as the links straighten. Self-locking machines hold loads safely at the cost of efficiency.
Flashcards
Flashcard
A structure with moving parts that turns an input force into an output force
Test your understanding
Question 1 of 5
A tool delivers a 360 N output force when you apply 45 N. What is its mechanical advantage?
Question 2 of 5
Pliers are squeezed with 40 N at 100 mm from the pivot and grip 25 mm from the pivot on the other side. What force does the pivot pin carry on one member?
Question 3 of 5
Ignoring friction, the input of a machine moves 300 mm while its output moves 20 mm. What is its ideal mechanical advantage?
Question 4 of 5
A jack has an ideal MA of 80 and an efficiency of 25%. What effort lifts a 4,000 N load?
Question 5 of 5
In a toggle press with a force P on the knee, what happens to the output force as the link angle θ shrinks towards zero?
