Statics › Section B · Forces and other vectors › Topic B.2

2D vectors and components

A force drawn at an angle is hard to add, balance or compare. Splitting it into perpendicular components turns every vector calculation in a plane into ordinary arithmetic, and converting back gives the magnitude and direction an engineer needs to report.

Why perpendicular axes

A coordinate system gives every point and vector a set of numbers. Statics uses orthogonal systems, whose axes are perpendicular. That choice makes the directions independent: a push along x has no effect along y, so each direction can be handled separately. The axes meet at the origin, from which positions are measured. Usually x points right and y points up, but you may move or rotate the axes to suit the problem, and it often pays to line one axis up with a major feature, such as a ramp or a beam. The physics topic "Two-dimensional motion and adding vectors" introduced components; here they are applied to forces.

Rectangular form

In rectangular, or Cartesian, coordinates a point is written as an ordered pair in parentheses, \(P = (x, y)\), the distances you travel along each axis to reach it from the origin. A vector is written with angle brackets, \(\mathbf{F} = \langle F_x, F_y \rangle\), or with unit vectors as \(F_x\mathbf{i} + F_y\mathbf{j}\). The brackets signal a vector rather than a location. For a force, the scalar components \(F_x\) and \(F_y\) say how much of the force acts in each direction. The coordinates of a point also define its position vector, the arrow from the origin straight to it.

Polar form

Polar coordinates describe the same point by its distance \(r\) from the origin and an angle \(\theta\), measured counterclockwise from the positive x axis. A force is described the same way, by its magnitude and direction, such as 200 N at 150°. Polar form is natural whenever distances and angles from a central point are what you know: the reach and swing of a tower crane, the joints of a robot arm, or a radar bearing. Always mark whether an angle is in degrees or radians. Both forms carry the same information, so you must be able to convert either way.

Polar to rectangular

Right-triangle trigonometry does the conversion. With \(\theta\) measured counterclockwise from the positive x axis,

F_x = F\cos\theta \qquad F_y = F\sin\theta

and the signs come out automatically. In practice it is safer to use the acute angle between the force and the nearest axis, compute both components as positive sizes, and then attach the signs by looking at the sketch: left and down are negative. This reference-angle approach keeps the geometry in view, and experience shows it causes fewer errors than feeding large angles to a calculator.

Worked example: resolving a force

A cable pulls on a bracket with 350 N, directed down and to the right at 40° below the positive x axis. Find its rectangular components. 1. Sketch: the force points into the fourth quadrant. 2. Sizes, using the 40° reference angle: \(350\cos 40^\circ = 268.1\) N and \(350\sin 40^\circ = 225.0\) N. 3. Signs from the sketch: right is positive, down is negative. 4. Result: \(\mathbf{F} = \langle 268.1, -225.0 \rangle\) N. 5. Check: \(\sqrt{268.1^2 + 225.0^2} = 350\) N, so the magnitude is recovered, and the x component is larger, as it should be for a force closer to the x axis.

Rectangular to polar

Going the other way, Pythagoras gives the magnitude and the inverse tangent gives the angle:

F = \sqrt{F_x^2 + F_y^2} \qquad \theta = \tan^{-1}\frac{F_y}{F_x}

The catch is the quadrant. A calculator's inverse tangent always returns an angle between \(-90^\circ\) and \(90^\circ\), in the first or fourth quadrant, because it cannot tell whether a negative ratio came from a negative \(F_y\) or a negative \(F_x\). If the components show the vector lies in the second or third quadrant, add \(180^\circ\) to the calculator's angle. Many calculators also have a built-in rectangular-to-polar function that handles the quadrant for you.

Worked example: a point in the second quadrant

Express the point \(P = (-6, 2.5)\) m in polar form, then do the same for the force \(\langle -120, -90 \rangle\) N. 1. Distance: \(r = \sqrt{(-6)^2 + 2.5^2} = 6.5\) m. 2. The calculator gives \(\tan^{-1}(2.5 / -6)\) as \(-22.6^\circ\), a fourth-quadrant angle. 3. But x is negative and y positive, so P is in the second quadrant:

\theta = -22.6^\circ + 180^\circ = 157.4^\circ

4. For the force: \(F = \sqrt{120^2 + 90^2} = 150\) N, and the calculator gives \(36.9^\circ\). 5. Both components are negative, so the force is in the third quadrant: \(\theta = 216.9^\circ\), that is 150 N at 36.9° below the negative x axis.

Angles from other references

Not every angle is measured from the x axis. If a force makes an angle \(\beta\) with the y axis, the roles swap: \(F_x = F\sin\beta\) and \(F_y = F\cos\beta\). A 180 N force tilted 25° to the left of the upward y axis has components \(-180\sin 25^\circ = -76.1\) N and \(180\cos 25^\circ = 163.1\) N. Directions are also often given as a slope triangle, such as a rise of 5 in a run of 12. The hypotenuse is 13, so a 260 N force along that slope, pointing up and to the right, has components \(260 \times \frac{12}{13} = 240\) N and \(260 \times \frac{5}{13} = 100\) N, with no trigonometry at all.

Worked example: tilted axes on a ramp

A 30 kg crate rests on a ramp inclined at 20° to the horizontal. Find the components of its weight along and perpendicular to the ramp. 1. Weight: \(W = 30 \times 9.81 = 294.3\) N, straight down. 2. Choose an x′ axis down the slope and a y′ axis perpendicular to it. 3. The angle between the weight and the y′ axis equals the ramp angle, 20°. 4. Along the slope: \(294.3\sin 20^\circ = 100.7\) N. Into the slope: \(294.3\cos 20^\circ = 276.6\) N. 5. Check: at 0° the along-slope part would vanish, and at 20° it is about a third of the weight, which is sensible.

Common mistakes to avoid

First, using cosine for the x component when the angle was measured from the y axis. Second, trusting the calculator's inverse tangent without checking the quadrant. Third, forgetting the signs when using reference angles: a force pointing left has a negative x component. Fourth, mixing up point notation \((x, y)\) with vector notation \(\langle F_x, F_y \rangle\). Fifth, leaving a calculator in radian mode while entering degrees.

Key takeaways

Perpendicular axes make directions independent. Points are written \((x, y)\) and vectors \(\langle F_x, F_y \rangle\) or \(F_x\mathbf{i} + F_y\mathbf{j}\). Polar form gives a magnitude and an angle measured counterclockwise from the positive x axis. Components are \(F\cos\theta\) and \(F\sin\theta\); with reference angles, attach the signs from a sketch. The magnitude is \(\sqrt{F_x^2 + F_y^2}\), and the inverse tangent needs \(180^\circ\) added in the second and third quadrants. Slope triangles give components without trigonometry, and tilted axes suit ramps.

Flashcards

Flashcard

Orthogonal axes

Perpendicular axes, so each direction is independent

Handle x and y separately.

Test your understanding

Question 1 of 5

A 500 N force points down and to the left, at 30° below the negative x axis. What are its rectangular components?

Question 2 of 5

What are the magnitude and direction of the force ⟨−80, 60⟩ N, with the angle measured counterclockwise from +x?

Question 3 of 5

A 150 N force acts up and to the right along a slope that rises 3 for every 4 across. What are its components?

Question 4 of 5

A 200 N force is tilted 30° to the right of the upward y axis. What is its x component?

Question 5 of 5

A crate weighing 400 N rests on a ramp inclined at 25°. What is the component of its weight parallel to the ramp?

← Previous topicNext topic →