Calculus › Section H · Applications of integrals › Topic H.5
Work
Push a box with a steady force and work is a simple product. But springs pull harder the further you stretch them, and water at the bottom of a tank climbs further than water at the top. When force or distance varies, work becomes an integral.
When force times distance breaks down
In physics, work is force times distance: pushing a crate with 50 newtons across 3 metres does \(150\) joules of work. The product is only valid when the force is constant. Stretch a spring, though, and it pulls back harder the further it goes; lift water out of a tank, and each layer starts at a different depth. In both cases the force changes with position. The fix is the same accumulation pattern that produced areas and volumes: over a tiny distance \(dx\), the force is very nearly constant, so the work done over that sliver is about \(F(x)\,dx\), and integrating adds the slivers up.
The work integral
If a force \(F(x)\) (in newtons) acts along a line from position \(a\) to position \(b\) (in metres), the work done is
measured in joules, because one joule is one newton-metre. The formula assumes the force depends only on position, not on time or speed, and points along the line of motion. The sign convention: work is positive when the force acts in the direction of motion, and negative when it opposes it, so the work you do stretching a spring is positive while the spring's force does negative work. Every problem in this topic is choosing \(F\), choosing the limits, and integrating.
Springs and Hooke's law
Hooke's law states that the force needed to hold a spring stretched \(x\) metres beyond its natural length is \(F = kx\), where \(k\) is the spring constant in newtons per metre. This holds only while the stretch stays within the spring's elastic limit; beyond it the spring deforms permanently. The work to stretch from the natural length to a total stretch of \(d\) is
Notice the square: doubling the stretch quadruples the work required. A spring with \(k = 60\) N/m stretched \(0.4\) m stores \(\frac{1}{2}(60)(0.16) = 4.8\) J.
Worked example: a spring in two stages
A force of 15 newtons holds a spring stretched 0.25 metres, so \(k = \frac{15}{0.25} = 60\) N/m. How much work stretches it from 0.25 m to 0.5 m?
Cross-check with the stored-energy formula: \(\frac{1}{2}k(0.5)^2 - \frac{1}{2}k(0.25)^2 = 7.5 - 1.875 = 5.625\) J. Both limits are measured from the natural length, never from wherever the spring happens to be sitting.
Worked example: pumping a tank dry
A cylindrical tank of radius 1 metre and height 3 metres is full of water, which must be pumped up and over the rim. Water's weight density is \(\rho g \approx 9{,}800\) newtons per cubic metre. Imagine the water in thin horizontal layers. A layer sitting \(y\) metres below the rim has volume \(\pi\,dy\) cubic metres, hence weight \(9{,}800\pi\,dy\) newtons, and it must be lifted \(y\) metres:
Sanity check: the whole tank of water weighs \(29{,}400\pi\) newtons, and the average layer starts halfway down, at depth 1.5 metres, so \(29{,}400\pi \times 1.5 = 44{,}100\pi\). The integral and the average agree.
Winding up a hanging rope
Work also accumulates when the distance varies while the weight is spread out. A uniform rope, 20 metres long and weighing 3 newtons per metre, hangs from a pulley. How much work winds it up onto the pulley? The piece of rope \(y\) metres below the pulley weighs \(3\,dy\) newtons and must rise \(y\) metres, so
Check by averages: the rope weighs 60 newtons in total, its centre sits 10 metres down, and \(60 \times 10 = 600\). The model assumes the rope is perfectly flexible and winds up without friction.
The pumping recipe, in general
Every pumping problem answers three questions. What does one layer weigh? Multiply the layer's volume by the weight density \(\rho g\) of the liquid, in newtons per cubic metre; for water that is about 9,800. How far does that layer rise? From its own position to the exit point, which may be the top of the tank or a pipe above it. And what is the variable? The depth \(y\), whose range runs from the top layer to the bottom layer. The tank's shape only enters through the layer's cross-section area \(A(y)\), the same function that appeared in volumes by slicing. Cylinders give constant \(A\); conical and spherical tanks make \(A\) depend on \(y\).
Common mistakes to avoid
The most common spring error is measuring from the wrong origin: \(x\) in Hooke's law is the stretch beyond natural length, so a spring already stretched 0.25 m needs its remaining work computed with limits 0.25 to 0.5, not 0 to 0.25. In pumping problems, the recurring slips are: using volume instead of weight (dropping the \(\rho g\) factor), letting every layer rise the full tank height instead of its own distance to the exit, and mixing units such as centimetres with the metre-based 9,800. And do not multiply the final force by the total distance: the changing force must be integrated, not sampled at the end.
Key takeaways
Work is force times distance when both are constant, and \(W = \int_a^b F(x)\,dx\) when the force varies with position; the unit is the joule. Hooke's law \(F = kx\) (stretch measured from natural length, within the elastic limit) gives stored work \(\frac{1}{2}kd^2\). Pumping integrates weight density times layer volume times lift distance over the layers, and winding a rope or cable integrates its weight per metre times each piece's distance up. When an average distance is easy to see, use it to check the integral.
Flashcards
Flashcard
Force times distance, in joules
Test your understanding
Question 1 of 5
A spring has k = 60 N/m. How much work stretches it 0.4 m from its natural length?
Question 2 of 5
A 15 N force holds a spring at 0.25 m stretch. How much work stretches it from 0.25 m to 0.5 m?
Question 3 of 5
A full cylindrical tank, radius 1 m and height 3 m, is pumped out over the rim (ρg ≈ 9,800 N/m³). How much work is required?
Question 4 of 5
A uniform 20 m rope weighing 3 N/m hangs from a pulley. How much work winds it all the way up?
Question 5 of 5
In Hooke's law F = kx, the stretch x is measured from where?
Standards: Beyond AP
