Chemistry › Section Q · Electrochemistry › Topic Q.5
Batteries and fuel cells
Phones, cars and spacecraft all carry galvanic cells engineered for one job each: cheap single use, high current, light weight, or a steady supply from a fuel tank. The chemistry of each design explains its voltage, its lifetime and its limits.
What makes a battery
A battery is one or more galvanic cells packaged as a portable power source. Cells in series add their voltages: six 2 V cells give 12 V. Primary cells are used once and thrown away, because their reaction cannot be reversed cleanly. Secondary cells are rechargeable. A cell's voltage is set by its chemistry, while its size sets its capacity, the total charge it can deliver. Capacity is often quoted in milliamp-hours: 1 mAh is 0.001 A for 3600 s, or 3.6 C.
Alkaline batteries
The familiar 1.5 V AA cell is an alkaline battery, an improved form of the older zinc-carbon dry cell. Powdered zinc in a potassium hydroxide paste is the anode, and manganese(IV) oxide mixed with graphite surrounds it as the cathode:
Adding the halves cancels the water and hydroxide, leaving
Only solids remain in the overall equation, so Q stays constant as the cell discharges, and the Nernst equation predicts a voltage that does not depend on how far the reaction has gone. A real alkaline cell still sags slowly, from about 1.5 V towards 1 V, as its internal resistance grows and the manganese oxide changes gradually in composition. Most alkaline cells are primary cells: charging them can make them leak corrosive potassium hydroxide.
The lead-acid battery
A car battery holds six lead-acid cells in series. Each has a lead anode and a lead(IV) oxide cathode in sulfuric acid:
Overall,
On discharge both plates turn into lead sulfate and sulfuric acid is used up, so the electrolyte becomes less dense; a hydrometer reading shows the state of charge. The battery is heavy, but cheap, and it delivers the large current a starter motor needs. Its lead makes recycling essential.
Worked example: a car battery's voltage and energy
Use the lead-acid half-reactions to find the standard cell voltage, the battery voltage and ΔG° per mole of lead. 1. The cathode is the \(\mathrm{PbO_2}\) plate, +1.69 V; the anode is the lead plate, −0.36 V. 2. \(E^\circ_{\text{cell}} = +1.69 - (-0.36) = +2.05\) V per cell. 3. Six cells in series: \(6 \times 2.05 = 12.3\) V, the "12 V" battery. 4. Each lead atom gives two electrons, so n = 2: \(\Delta G^\circ = -2 \times 96{,}485 \times 2.05 = -3.96 \times 10^5\) J, or −396 kJ per mole of lead. 5. Check: the lead plate is the anode, so it is the negative terminal, and a positive voltage goes with a negative ΔG°, as it must.
Lithium-ion batteries
Lithium sits at the bottom of the reduction table, −3.04 V, and is the lightest metal, so lithium cells pack high voltage into little mass. In a lithium-ion cell no lithium metal is present. Lithium ions slip in and out of layered solids: graphite at the anode and a metal oxide, such as lithium cobalt oxide, at the cathode. On discharge,
Ions cross the electrolyte from graphite to oxide while electrons go round the circuit; charging sends both back. The cell gives about 3.7 V. Its electrolyte is a lithium salt in an organic solvent, not water, which the voltage would split. That solvent is flammable, so damaged or overheated cells can catch fire.
Recharging: running a cell backwards
Charging a secondary cell connects it to a supply that pushes electrons the opposite way, forcing the non-spontaneous reverse reaction. For that to work, the products of discharge must stay where they formed, as solid lead sulfate does on the plates or lithium ions do inside the electrode layers. During charging, the electrode that was the anode becomes the site of reduction, so the names anode and cathode swap even though the terminals keep their signs. Nickel-metal hydride cells, about 1.2 V each, are a common rechargeable choice for AA sizes, replacing the older nickel-cadmium cells, whose cadmium is toxic.
Fuel cells
In a fuel cell, the reactants are not sealed inside but fed in continuously, so the cell runs as long as fuel and oxygen arrive. In a hydrogen fuel cell with an acidic membrane,
The hydrogen ions cross the membrane, and the overall reaction is \(\mathrm{2H_2 + O_2 \rightarrow 2H_2O}\), with \(E^\circ = 1.23\) V. Platinum catalysts on the electrodes speed both halves. Under load, a single cell gives somewhat less, typically below 1 V, so cells are stacked in series. The only chemical product is water, which is why fuel cells have powered spacecraft and some buses and cars.
Worked example: maximum work from hydrogen
How much electrical work can a hydrogen fuel cell deliver per mole of liquid water formed? 1. Per mole of water, \(\mathrm{H_2 + \tfrac{1}{2}O_2 \rightarrow H_2O(l)}\), each hydrogen molecule gives two electrons, so n = 2. 2. \(\Delta G^\circ = -2 \times 96{,}485 \times 1.23 = -2.37 \times 10^5\) J, so at most 237 kJ of work. 3. Compare with the heat released by burning, ΔH° = −285.8 kJ per mole from the enthalpy topic: the fuel cell can turn up to 237 ÷ 285.8 = 83 percent of that energy into work. 4. Check: a heat engine running between 800 K and 300 K can convert at most \(1 - \frac{300}{800} = 62.5\) percent of its heat. A fuel cell is not a heat engine, so that limit does not apply.
Energy density and choosing a source
Engineers compare power sources by energy density, the energy stored per kilogram. Petrol releases about 46 MJ kg⁻¹ when burned and hydrogen about 142 MJ kg⁻¹, while lithium-ion cells store roughly 0.5 to 1 MJ kg⁻¹. That gap is why long-haul aircraft still burn liquid fuel. Batteries suit vehicles that can recharge often, because an electric motor uses most of a battery's energy, while a petrol engine turns only about a fifth to a third of its fuel's energy into motion. Hydrogen is light but bulky, so cars store it at around 700 bar.
Common mistakes to avoid
First, thinking a bigger cell gives a higher voltage: size raises capacity, and voltage comes from the chemistry. Second, forgetting that cells in series add their voltages. Third, multiplying \(E^\circ\) by coefficients when finding a battery's voltage. Fourth, using n = 4 for one mole of water in the fuel cell; four electrons go with two moles of water. Fifth, saying lithium-ion cells contain lithium metal: they shuttle lithium ions. Sixth, treating a fuel cell as a heat engine bound by \(1 - T_c/T_h\).
Key takeaways
Batteries are packaged galvanic cells: voltage depends on chemistry, capacity on size, and series cells add voltages. Alkaline cells, Zn and \(\mathrm{MnO_2}\) in KOH, give about 1.5 V; only solids appear in the overall reaction, so Q stays fixed. A lead-acid cell gives 2.05 V, six making 12 V, and recharges because \(\mathrm{PbSO_4}\) stays on the plates. Lithium-ion cells shuttle \(\mathrm{Li^+}\) between graphite and a metal oxide at about 3.7 V. Fuel cells take a continuous feed; the hydrogen cell gives 1.23 V standard and up to 237 kJ of work per mole of water.
Flashcards
Flashcard
One or more galvanic cells packaged as a power source
Test your understanding
Question 1 of 5
A lead-acid cell uses PbO₂/PbSO₄ (E° = +1.69 V) and PbSO₄/Pb (E° = −0.36 V). What is the standard potential of one cell?
Question 2 of 5
Why does the Nernst equation predict that an alkaline cell's voltage should not depend on how far its reaction has gone?
Question 3 of 5
What is the main difference between a fuel cell and a battery?
Question 4 of 5
In a lithium-ion cell that is powering a phone, what do the lithium ions do?
Question 5 of 5
A hydrogen fuel cell has E° = 1.23 V. What is the maximum electrical work per mole of liquid water formed?
