Chemistry › Section A · Essential ideas › Topic A.5

Uncertainty, significant figures, and unit conversions

No measurement is perfect, and an answer should never claim more certainty than the data behind it. Significant figures keep results honest, and dimensional analysis lets units guide every conversion and calculation.

Exact numbers and measured numbers

Some numbers are exact. Counted numbers are exact: a class of 28 students has exactly 28, not 27.9. Defined numbers are exact too: 1 kg is exactly 1000 g, and 1 inch is exactly 2.54 cm by definition. Every measured number, however, carries some uncertainty, because instruments have limits. A kitchen scale might show 152 g for an apple, and a laboratory balance 151.62 g. Both are honest readings; the second is simply more certain, and the way each is written shows that.

Reading a scale: significant figures

When reading a scale, record every digit you are sure of plus one estimated digit. A thermometer marked every 1 °C, with the liquid just under halfway from 23 to 24, reads 23.4 °C: the 2 and 3 are certain, and the 4 is a careful estimate. Writing 23.43 °C would claim more than the scale can give. The certain digits plus the one estimated digit are the significant figures, so 23.4 °C has three. On a digital display the last digit is the uncertain one: a balance reading 8.07 g means roughly 8.06 to 8.08 g.

Which zeros count

Nonzero digits are always significant, so only zeros need thought. Zeros between nonzero digits (captive zeros) are significant: 2.05 g has three significant figures. Leading zeros only locate the decimal point and are never significant: 0.0042 m has two, as \(4.2 \times 10^{-3}\) m makes clear. Trailing zeros after a decimal point are significant, because nobody writes them unless they were measured: 3.20 mL has three. Trailing zeros in a whole number with no decimal point are ambiguous: 1500 g might have two, three or four. Scientific notation removes the doubt: \(1.5 \times 10^3\), \(1.50 \times 10^3\) or \(1.500 \times 10^3\) g. In this course, an ambiguous trailing zero is treated as not significant.

Rules for calculated results

A calculated answer cannot be more certain than its least certain measurement. When adding or subtracting, round to the fewest decimal places: \(12.52 + 3.1 = 15.62\), reported as 15.6. When multiplying or dividing, round to the fewest significant figures: \(4.27 \times 1.8 = 7.686\), reported as 7.7. Exact numbers never limit the answer. Keep extra digits during a calculation and round only once, at the end. To round, look at the first digit you drop: below 5, leave the last kept digit alone; above 5, or 5 followed by any nonzero digit, round up. For a 5 followed by nothing or only zeros, this course rounds to make the kept digit even (2.45 becomes 2.4, 2.55 becomes 2.6); some courses always round it up.

Worked example: density of a liquid

An empty beaker has a mass of 31.2 g. With a liquid added, the mass is 48.30 g, and the liquid's volume is 22.6 mL. Find the density. 1. Mass of liquid: \(48.30 - 31.2 = 17.10\) g. Subtraction keeps the fewest decimal places, one, so this is 17.1 g. 2. Density: \(17.10 \div 22.6 = 0.75664...\) g/mL. 3. Division keeps the fewest significant figures: 17.1 and 22.6 both have three, so the answer is 0.757 g/mL. The leading zero is not significant. 4. Check: \(0.757 \times 22.6 \approx 17.1\) g, matching the mass.

Accuracy and precision

Accuracy is how close a measurement is to the true or accepted value. Precision is how close repeated measurements are to each other. They are independent: darts clustered tightly in one corner of a board are precise but not accurate. Random errors, such as small reading differences, scatter results and hurt precision. Systematic errors, such as a balance that always reads 0.5 g too high, shift every result the same way and hurt accuracy without spoiling precision. Accuracy is often expressed as a percent error:

\text{percent error} = \frac{|\text{measured} - \text{accepted}|}{\text{accepted}} \times 100\%

Repeats reveal precision; a known standard reveals accuracy.

Worked example: judging three data sets

Three groups measure the density of water at 20 °C, where the accepted value is 0.998 g/mL. Group A: 0.997, 0.999, 0.998. Group B: 1.049, 1.051, 1.050. Group C: 0.95, 1.04, 1.01. 1. Spreads: A and B each span only 0.002 g/mL, so both are precise; C spans 0.09 g/mL, so it is imprecise. 2. Means: A is 0.998, B is 1.050 and C is 1.00 g/mL. 3. Percent errors: A is 0 percent; B is \(\frac{1.050 - 0.998}{0.998} \times 100\% \approx 5.2\%\); C's mean, 1.00, matches 0.998 to its two decimal places. 4. Verdict: A is accurate and precise. B is precise but inaccurate, suggesting a systematic error such as a miscalibrated cylinder. C is close on average but imprecise, so its good mean is partly luck.

Dimensional analysis

Dimensional analysis, or the factor-label method, treats units like algebra: they multiply, divide and cancel along with the numbers. A conversion factor is a ratio of two equal quantities, such as \(\frac{1000 \text{ m}}{1 \text{ km}}\), so it equals 1 and multiplying by it changes the units without changing the quantity. Arrange each factor so the unwanted unit cancels:

5.20 \text{ km} \times \frac{1000 \text{ m}}{1 \text{ km}} = 5.20 \times 10^3 \text{ m}

For squared or cubed units, apply the factor that many times: \(2.70 \text{ g/cm}^3 \times \frac{1 \text{ kg}}{1000 \text{ g}} \times \left(\frac{100 \text{ cm}}{1 \text{ m}}\right)^3 = 2.70 \times 10^3 \text{ kg/m}^3\). If the units come out right, the set-up is almost certainly right.

Worked example: a speed in new units

A car travels at 65.0 miles per hour. What is this in metres per second? Use 1 mile = 1609.344 m (exact) and 1 hour = 3600 s (exact). 1. Set up factors so that miles and hours cancel:

65.0 \frac{\text{mi}}{\text{h}} \times \frac{1609.344 \text{ m}}{1 \text{ mi}} \times \frac{1 \text{ h}}{3600 \text{ s}}

2. Calculate: \(65.0 \times 1609.344 \div 3600 = 29.0576...\) m/s. 3. Significant figures: the conversion factors are exact, so only 65.0 limits the answer, to three figures: 29.1 m/s. 4. Check: 1 m/s is about 2.24 mi/h, and \(29.1 \times 2.24 \approx 65\).

Converting temperatures

Temperature scales have different zero points, so converting needs more than one factor. The Fahrenheit scale puts water's freezing point at 32 °F and boiling point at 212 °F, so 180 Fahrenheit degrees span the same range as 100 Celsius degrees, a ratio of 9 to 5:

T(^{\circ}\text{F}) = \tfrac{9}{5}\,T(^{\circ}\text{C}) + 32 \qquad T(^{\circ}\text{C}) = \tfrac{5}{9}\big(T(^{\circ}\text{F}) - 32\big)

Body temperature, 37.0 °C, is \(1.8 \times 37.0 + 32 = 98.6\) °F. An oven at 375 °F is \(\tfrac{5}{9}(375 - 32) \approx 191\) °C, which is \(190.56 + 273.15 \approx 464\) K. The 32, the 9/5 and the 273.15 are exact.

Common mistakes to avoid

First, rounding at every step: carry extra digits and round once at the end. Second, using the significant-figure rule for addition when multiplying, or the reverse. Third, counting leading zeros as significant: 0.0050 has two significant figures, not four. Fourth, letting exact numbers, such as 1000 g per kg or a count of 3 trials, limit the answer. Fifth, flipping a conversion factor, which leaves units like km² per m instead of cancelling them. Sixth, calling tightly grouped results accurate: they are precise, and a systematic error can still make them all wrong. Seventh, converting °F to °C by multiplying alone, forgetting the 32.

Key takeaways

Counted and defined numbers are exact; measured numbers have significant figures, the certain digits plus one estimate. Leading zeros never count; captive zeros and trailing zeros after a decimal point do. Adding or subtracting keeps the fewest decimal places; multiplying or dividing keeps the fewest significant figures; round once, at the end. Accuracy is closeness to the true value, precision is agreement between repeats. Conversion factors equal 1 and are arranged so units cancel; temperature conversions also need the offset between zero points.

Flashcards

Flashcard

Exact number

A counted or defined number with no uncertainty

28 students; 1 inch = 2.54 cm.

Test your understanding

Question 1 of 5

How many significant figures does 0.004060 g have?

Question 2 of 5

Three masses are added: 12.4 g + 3.725 g + 0.16 g. How should the total be reported?

Question 3 of 5

A cart rolls 8.25 m in 2.1 s. How should its average speed be reported?

Question 4 of 5

A 5.00 g standard mass is weighed three times on a balance, giving 5.42 g, 5.43 g and 5.41 g. How would you describe these results?

Question 5 of 5

A train travels at 90.0 km/h. What is this speed in metres per second?

← Previous topicNext topic →