Electrical Engineering › Section B · Resistance, Ohm's law, power, and energy › Topic B.6

Circuit breakers, GFCIs, fuses, and safety

Too much current overheats wires and starts fires, and a small current through the body can kill. Fuses, breakers and ground-fault interrupters exist to stop both, and understanding how they work is part of working safely with electricity.

Why circuits need protection

Every wire has some resistance, so current heats it at a rate of \(I^2R\). Wire sizes are chosen so that the normal current keeps the insulation well below its temperature limit. An overload, such as too many appliances on one circuit, raises the current moderately but for a long time. A short circuit, a near-zero-resistance path between conductors, raises it enormously and almost instantly. Either way the heating can melt insulation and start a fire. Protective devices sit in series with the circuit and open it when the current exceeds a safe value, protecting the wiring first and the equipment second.

Fuses

A fuse is a deliberately weak link: a metal element that melts and opens the circuit when the current is too high for too long. A fuse is specified by its current rating, its voltage rating and its breaking capacity, the largest fault current it can interrupt safely. Fast-acting fuses blow quickly and protect sensitive electronics. Time-delay, or slow-blow, fuses tolerate brief surges, such as the inrush when a motor starts, while still blowing on a sustained overload. Once blown, a fuse must be replaced with one of the same type and rating. A larger fuse, or a bypass, removes the protection the wiring depends on.

Circuit breakers

A circuit breaker is a switch that opens itself on overcurrent and can then be reset. Most household breakers are thermal-magnetic. The thermal element is a bimetallic strip, two bonded metals that expand at different rates; sustained overload current heats it until it bends and trips the latch, more quickly for larger overloads. The magnetic element is a coil that, during a short circuit, produces enough force to trip the mechanism within a fraction of a second. US homes commonly use 15 A and 20 A breakers on 120 V branch circuits. A breaker that trips repeatedly is reporting a fault or an overload; resetting it again and again does not fix the cause.

Worked example: a kitchen circuit

A 20 A breaker protects a 120 V kitchen circuit. A 1500 W kettle, a 1100 W microwave oven and a 900 W toaster are switched on together. Will the breaker trip? 1. Total power: \(1500 + 1100 + 900 = 3500\) W. 2. Total current, from \(P = VI\): \(I = \frac{3500}{120} = 29.2\) A. 3. Compare: 29.2 A is about 46% above the 20 A rating, a sustained overload. 4. Result: the thermal element will trip the breaker after a delay, often a few minutes for an overload of this size; the exact time follows the breaker's trip curve. 5. Check the capacity: at 120 V, 20 A corresponds to \(120 \times 20 = 2400\) W, so any two of these appliances together are within the rating but all three are not.

Electricity and the body

Harm comes from current through the body, and the voltage matters because it drives that current through the body's resistance. Very roughly, for mains-frequency current: about 1 mA can be felt; around 10 mA or more can cause muscle contraction strong enough that a person cannot let go; and about 100 mA through the chest can trigger ventricular fibrillation, a chaotic heart rhythm that is often fatal without prompt treatment. Body resistance varies enormously. Dry, intact skin may present around 100 kΩ, but wet or broken skin can drop it to about 1 kΩ, so the same voltage becomes far more dangerous in a bathroom or outdoors.

Worked example: dry hands and wet hands

Estimate the current through a person who touches 120 V, first with dry hands and then with wet ones, using the rough resistances above. 1. Dry skin, about 100 kΩ: \(I = \frac{V}{R} = \frac{120\,\text{V}}{100\,\text{k}\Omega} = 1.2\) mA, around the threshold of feeling. 2. Wet skin, about 1 kΩ: \(I = \frac{120\,\text{V}}{1\,\text{k}\Omega} = 120\) mA. 3. Compare: the current is 100 times larger, well into the range that can cause fibrillation. 4. Conclusion: the voltage did not change, only the resistance, which is why water and electricity are such a dangerous mix. These figures are order-of-magnitude estimates for awareness, not safe limits.

Ground-fault circuit interrupters

A fuse or breaker rated 15 A ignores a 50 mA current through a person. A ground-fault circuit interrupter (GFCI), called a residual-current device (RCD) in much of the world, protects people instead. It compares the current in the hot conductor with the current returning in the neutral. Normally they are equal; if some current leaks to ground, perhaps through a person, there is an imbalance. US GFCIs for personal protection trip at an imbalance of about 4 to 6 mA, faster for larger leaks, within a few hundredths of a second for dangerous currents; RCDs on 230 V, 50 Hz systems commonly trip at 30 mA. Codes require GFCI protection in wet locations. Press the test button regularly to confirm it still trips.

Worked example: a leaking appliance

A faulty washing machine on a GFCI-protected 120 V circuit draws 8.000 A through the hot conductor, but only 7.990 A returns through the neutral. 1. Imbalance: \(8.000 - 7.990 = 0.010\) A, or 10 mA. 2. Where it went: 10 mA is leaving the circuit through some other path to ground, such as the machine's metal case or a person touching it. 3. Compare: 10 mA exceeds the GFCI's trip level of about 4 to 6 mA, so the GFCI opens the circuit. 4. Note that the machine's 8 A is far below a 20 A breaker's rating, so the breaker alone would never react. Only the GFCI sees the leak, because it watches the difference, not the total.

Grounding, AFCIs and safe practice

The third, round pin on a US plug connects metal cases to the equipment grounding conductor. If a live wire touches the case, fault current flows through that low-resistance path and the breaker or fuse opens, instead of the case staying live. Arc-fault circuit interrupters (AFCIs) watch for the current signature of arcing from damaged cords or loose connections, a common cause of house fires. When working on equipment, switch off and isolate it, lock and tag the isolation, and verify that it is dead with a meter you have just checked on a known live source. Treat capacitors as charged. Never work on live mains; mains wiring is for qualified electricians under the applicable code, such as the US National Electrical Code.

Common mistakes to avoid

First, replacing a blown fuse with a higher-rated one, or bridging it, which leaves the wiring unprotected. Second, assuming a breaker protects people: a 20 A breaker will not trip on a current that can stop a heart. Third, thinking low voltage is always safe: the current depends on resistance too, and wet skin conducts well. Fourth, resetting a breaker repeatedly without finding the fault. Fifth, removing a plug's ground pin. Sixth, trusting a meter's "dead" reading without first proving the meter works.

Key takeaways

Overcurrent heats wiring at I²R and can start fires; fuses and breakers open the circuit to protect the wiring. Fuses melt and must be replaced like for like; time-delay types tolerate motor inrush. Thermal-magnetic breakers trip thermally on overloads and magnetically on shorts. About 1 mA is felt, around 10 mA can prevent letting go, and about 100 mA through the chest can cause fibrillation; wet skin lowers body resistance dramatically. GFCIs compare hot and neutral current and trip at about 4 to 6 mA. Ground metal cases, isolate and lock out before work, and never work live.

Flashcards

Flashcard

Overload

Moderately excessive current for a long time

Too many appliances on one circuit.

Test your understanding

Question 1 of 5

A 15 A breaker protects a 120 V circuit. A 1500 W heater and a 1200 W hair dryer run together for a long time. What happens?

Question 2 of 5

What does a GFCI measure in order to decide whether to trip?

Question 3 of 5

Why is a time-delay fuse usually chosen for a motor circuit?

Question 4 of 5

Estimate the current if 240 V is applied across a wet-skin body path of about 2.0 kΩ.

Question 5 of 5

In a thermal-magnetic breaker, which element responds within a fraction of a second to a short circuit?

← Previous topicNext topic →