Electrical Engineering › Section C · Series circuits › Topic C.1
Series circuits and sources in series
String parts end to end and they must all carry the same current. That single fact makes series circuits the easiest networks to analyse, and the rules you learn here run through every circuit that follows.
What makes elements series
A circuit is a set of elements joined at terminal points so that there is at least one closed path for charge. Two elements are in series when they share exactly one terminal and nothing else that carries current is connected at that shared point. Because charge cannot pile up at the junction or leak away from it, the same current must pass through both. That is the test to use: if the current through two elements must be identical, they are in series. A branch is any part of a circuit made of one or more elements in series, such as a single resistor or a source with a resistor next to it.
One current, rises and drops
This course uses conventional current, the direction positive charge would move. In a circuit with one source, current leaves the source's positive terminal, passes through each resistor in turn and returns to the negative terminal. Electrons actually drift the other way, but every result here is the same either way. Following the current, the potential rises across the source, from minus to plus, and falls across each resistor, from plus to minus. Under the passive sign convention, current enters the positive terminal of each resistor, so each resistor absorbs power, as it must.
Total resistance
For \(N\) resistors in series, the total resistance is the sum:
The source cannot tell how this total is made up. It sees one resistance \(R_T\), so you can redraw the circuit as the source across a single resistor. Two consequences follow. Adding a resistor in series always raises \(R_T\), so the total is always larger than the largest single resistor. And \(N\) equal resistors \(R\) in series give \(R_T = NR\): five 220 Ω resistors make 1.1 kΩ.
Current, then each voltage
Once you know \(R_T\), Ohm's law gives the source current, \(I_s = E/R_T\). That same current flows through every element, so the voltage across each resistor is \(V_k = IR_k\). A larger resistor therefore takes a larger share of the source voltage, in direct proportion to its resistance. The power each resistor absorbs follows from any of the three forms in Power, efficiency, and energy, \(P = VI = I^2R = V^2/R\), and the source delivers \(P_s = EI_s\). Energy is conserved, so the power delivered equals the sum of the powers absorbed.
Worked example: three resistors on 12 V
A 12 V source drives \(R_1 = 1.5\,\text{k}\Omega\), \(R_2 = 3.3\,\text{k}\Omega\) and \(R_3 = 1.2\,\text{k}\Omega\) in series. 1. Total resistance: \(R_T = 1.5 + 3.3 + 1.2 = 6.0\,\text{k}\Omega\). 2. Current: \(I = 12\,\text{V} / 6.0\,\text{k}\Omega = 2.0\,\text{mA}\). 3. Voltages: \(V_1 = 3.0\,\text{V}\), \(V_2 = 6.6\,\text{V}\), \(V_3 = 2.4\,\text{V}\). 4. Powers, from \(P = VI\): 6.0 mW, 13.2 mW and 4.8 mW. 5. Check: the voltages add to 12 V, and the source delivers \(12 \times 2.0 = 24\,\text{mW}\), which equals \(6.0 + 13.2 + 4.8\). The largest resistor takes the largest voltage and the most power.
Worked example: working backwards
A 15 V source feeds a series string of an unknown \(R_1\), \(R_2 = 4.7\,\text{k}\Omega\) and \(R_3 = 3.3\,\text{k}\Omega\). An ammeter in the loop reads 1.5 mA. Find \(R_1\). 1. The source sees \(R_T = E/I = 15\,\text{V} / 1.5\,\text{mA} = 10\,\text{k}\Omega\). 2. Subtract the known parts: \(R_1 = 10 - 4.7 - 3.3 = 2.0\,\text{k}\Omega\), a standard value. 3. Check with voltages: \(V_1 = 3.0\,\text{V}\), \(V_2 = 7.05\,\text{V}\), \(V_3 = 4.95\,\text{V}\), which add to 15 V. Problems like this need you to pick the right equation first: here the given current and voltage fix \(R_T\) before anything else.
Voltage sources in series
Sources can also be connected in series to raise or lower the total voltage. Sources that push current the same way around the loop are aiding, and their voltages add. A source turned the other way is opposing, and its voltage subtracts. The net voltage is the sum of the aiding group minus the sum of the opposing group, and it takes the polarity of the larger group. Four 1.5 V cells placed end to end, positive to negative, give 6 V. Turn one cell round by mistake and the stack gives only 3 V, because that cell now subtracts 1.5 V instead of adding it.
Worked example: an opposing source
A 15 V source \(E_1\) and a 6 V source \(E_2\) are in a single loop with \(R_1 = 1\,\text{k}\Omega\) and \(R_2 = 2\,\text{k}\Omega\), with \(E_2\) turned to oppose \(E_1\). 1. Net voltage: \(15 - 6 = 9\,\text{V}\), in the direction set by \(E_1\). 2. Current: \(I = 9\,\text{V} / 3\,\text{k}\Omega = 3.0\,\text{mA}\). 3. Resistor voltages: 3.0 V and 6.0 V. 4. Powers: \(E_1\) delivers \(15 \times 3.0 = 45\,\text{mW}\). Current enters the positive terminal of \(E_2\), so under the passive sign convention \(E_2\) absorbs \(6 \times 3.0 = 18\,\text{mW}\), as a battery on charge does. The resistors absorb 9 mW and 18 mW. 5. Check: \(45 = 18 + 9 + 18\).
When one element opens
Because a series circuit has only one path, a single break stops the current everywhere. If one resistor burns out and becomes an open circuit, the current falls to zero, so every intact resistor has \(V = IR = 0\) across it. The whole source voltage then appears across the gap, since there is no drop anywhere else to share it. This is why an old-style string of series lamps goes completely dark when one filament fails. It also suggests a useful idea for later: in a dead series circuit, the faulty part is the one with the full supply voltage across it.
Common mistakes to avoid
First, calling two elements series just because they sit next to each other on the page: if a third current-carrying wire joins at their shared point, they are not in series. Second, assuming the current is larger near the positive terminal or gets used up along the string; it is the same everywhere in the loop. Third, adding opposing sources instead of subtracting them, so check which way each one pushes current. Fourth, thinking the smallest resistor dissipates the most power in a series string: with equal current, \(P = I^2R\) makes the largest resistor the hottest.
Key takeaways
Elements are in series when they share one terminal with nothing else current-carrying attached there, so they carry the same current. Series resistances add, R_T = R₁ + R₂ + … + R_N, so the total exceeds the largest part, and N equal resistors give NR. The source current is E/R_T, each voltage is IR_k, and the power delivered equals the total power absorbed. Aiding sources add and opposing sources subtract. A single open stops all current and puts the full source voltage across the break.
Flashcards
Flashcard
Share exactly one terminal, with no other current-carrying element at that point
Test your understanding
Question 1 of 5
Resistors of 2.2 kΩ, 3.3 kΩ and 4.7 kΩ are in series across a 20.4 V source. What current flows?
Question 2 of 5
A 12 V source drives 1.5 kΩ, 3.3 kΩ and 1.2 kΩ in series. Which resistor absorbs the most power?
Question 3 of 5
A 9 V and a 6 V source aid each other in a loop, and a 3 V source opposes them. What is the net source voltage?
Question 4 of 5
A 15 V source drives a 2.2 kΩ resistor, a 1.8 kΩ resistor and an unknown resistor in series, and the current is 2.5 mA. What is the unknown resistance?
Question 5 of 5
Three resistors are in series across 12 V, and one of them burns open. What happens?
