Electrical Engineering › Section B · Resistance, Ohm's law, power, and energy › Topic B.5
Power, efficiency, and energy
Voltage and current tell you how a circuit behaves; power and energy tell you what it costs, how hot it runs and how long a battery lasts. This topic links them, measures how much of the input a machine turns into useful output, and turns kilowatt-hours into dollars.
Power is a rate
Power is the rate at which energy is converted or transferred:
in watts (W), where 1 W is 1 joule per second. A 60 W lamp converts 60 J of electrical energy into light and heat every second. Since voltage is energy per charge and current is charge per second, multiplying them gives energy per second:
For mechanical output, motors are still often rated in horsepower, with 1 hp equal to about 745.7 W. Power ratings are central to design: they decide wire sizes, component sizes and how much heat a box must shed.
Three forms for a resistor
For a resistor, Ohm's law lets either \(V\) or \(I\) be eliminated from \(P = VI\):
Choose the form that uses the quantities you know. The \(I^2R\) form shows why doubling the current in a wire quadruples the heat produced in it, which is why transmission lines run at high voltage and low current. The \(\frac{V^2}{R}\) form shows that, at a fixed voltage, a smaller resistance draws more power: a 1500 W heater has a lower resistance than a 60 W lamp on the same outlet. All power in a resistor becomes heat, and its power rating is the most it can shed safely.
Worked example: sizing a resistor
A 56 Ω resistor is connected across a 12 V supply. Find the power and choose a power rating. 1. Current: \(I = \frac{12}{56} = 0.2143\) A. 2. Power from \(VI\): \(12 \times 0.2143 = 2.57\) W. 3. Check with the other forms: \(I^2R = (0.2143)^2 \times 56 = 2.57\) W and \(\frac{V^2}{R} = \frac{144}{56} = 2.57\) W, which agree. 4. Rating: a 0.25 W or 1 W part would overheat. A common design rule is to allow roughly twice the expected dissipation, about 5.1 W here, so a standard 5 W resistor is the sensible choice. 5. Note that the resistor still gets warm; a 5 W part dissipating 2.6 W can be too hot to touch.
Who supplies and who absorbs
With the passive sign convention, calculate \(P = VI\) using the current that enters the element's + terminal. A positive answer means the element absorbs power; a negative answer means it delivers power. A resistor always absorbs. A battery running a torch has current leaving its + terminal, so the current entering + is negative: a 9.0 V battery supplying 0.50 A has \(P = 9.0 \times (-0.50) = -4.5\) W, meaning it delivers 4.5 W. A battery on charge has current pushed into its + terminal and absorbs power. In any circuit, the power delivered equals the power absorbed, because energy is conserved.
Wattmeters
Because power depends on both voltage and current, a wattmeter needs both. A classic wattmeter has a current coil, connected in series with the load like an ammeter, and a voltage coil, connected across the load like a voltmeter; the deflection follows their product. Digital power meters sample voltage and current electronically and multiply them. The plug-in energy monitors sold for household use are digital wattmeters that also add up energy over time, which makes them handy for finding which appliance dominates a bill. Measurement on mains equipment calls for the same caution as any mains work: isolate, use rated equipment, never work live. "Wattmeters and effective resistance" extends this to ac.
Efficiency
No machine turns all its input into useful output. Some energy is always lost, mostly as heat, through winding resistance, friction and similar effects. The efficiency is the fraction that comes out usefully:
where \(P_o\) is the output power and \(P_i\) the input. The losses are \(P_i - P_o\). Efficiency can never exceed 100%. Large transformers reach above 99%, good electric motors often above 90%, small motors far less, and an incandescent lamp, judged on light, under 5%. For systems in cascade, with each stage feeding the next, the overall efficiency is the product: \(\eta_T = \eta_1\eta_2\eta_3\).
Worked example: a pump motor
A dc pump motor draws 6.50 A from a 120 V supply and delivers 0.800 hp of mechanical output. 1. Input power: \(P_i = VI = 120 \times 6.50 = 780\) W. 2. Output power in watts: \(P_o = 0.800 \times 745.7 = 597\) W. 3. Efficiency: \(\eta = \frac{597}{780} \times 100\% = 76.5\%\). 4. Losses: \(780 - 597 = 183\) W, almost all of it heat in the windings and bearings. 5. Check: the efficiency lies below 100% and is typical of a small motor, and the output in watts is less than the input, as it must be.
Worked example: a chain of stages
An electric cart charges its battery through a 90% efficient charger; the battery returns 85% of the energy put into it, and the motor drive is 80% efficient. 1. Overall efficiency: \(\eta_T = 0.90 \times 0.85 \times 0.80 = 0.612\), or 61.2%. 2. To deliver 500 W of mechanical output, the input from the outlet must be \(P_i = \frac{P_o}{\eta_T} = \frac{500}{0.612} = 817\) W. 3. Lesson: the overall efficiency is lower than any single stage, so improving the weakest stage pays most. If the motor drive rose to 90%, \(\eta_T\) would rise to \(0.90 \times 0.85 \times 0.90 = 68.9\%\).
Energy and the electricity bill
Energy is power multiplied by time:
In joules, \(P\) is in watts and \(t\) in seconds. Utilities instead bill in kilowatt-hours (kWh): the energy used by 1 kW for 1 h, which is \(1000 \times 3600 = 3.6 \times 10^{6}\) J. To find energy in kWh, put power in kilowatts and time in hours. For example, a 1.5 kW space heater run 4 h a day for 30 days uses \(1.5 \times 4 \times 30 = 180\) kWh; at $0.16 per kWh that costs \(180 \times 0.16 = 28.80\), or $28.80. Replacing a 60 W incandescent lamp with a 9 W LED of similar brightness cuts its energy use by 85%.
Common mistakes to avoid
First, using minutes, or watts instead of kilowatts, when calculating kWh. Second, confusing power, a rate in watts, with energy, an amount in joules or kWh. Third, forgetting to square in \(I^2R\) or \(\frac{V^2}{R}\). Fourth, choosing a resistor whose rating only just equals its dissipation. Fifth, adding stage efficiencies instead of multiplying them. Sixth, mixing horsepower and watts in one efficiency calculation. Seventh, losing the sign convention: a negative absorbed power means the element is supplying power.
Key takeaways
Power is the rate of energy transfer, P = W/t, in watts. For any element P = VI, and for a resistor also I²R and V²/R. Under the passive sign convention a positive P is absorbed and a negative P is delivered; total supplied equals total absorbed. A wattmeter senses current in series and voltage in parallel. Efficiency η = Pₒ/Pᵢ × 100%, never above 100%; cascaded stages multiply. One horsepower is about 745.7 W. Energy W = Pt; 1 kWh = 3.6 × 10⁶ J, and cost is kWh times the price per kWh.
Flashcards
Flashcard
Power is energy per unit time
Test your understanding
Question 1 of 5
What power is dissipated by a 48 Ω resistor with 24 V across it?
Question 2 of 5
A 220 Ω resistor carries 0.30 A. What power does it dissipate?
Question 3 of 5
A system has two stages in cascade, 90% and 80% efficient. What is its overall efficiency?
Question 4 of 5
A 2.0 kW appliance runs for 90 minutes. At $0.15 per kWh, what does the energy cost?
Question 5 of 5
A 9.0 V battery supplies 0.50 A to a torch, with current leaving its + terminal. Using the passive sign convention, what is the battery's absorbed power?
