Electrical Engineering › Section D · Parallel and series-parallel circuits › Topic D.3

The current divider rule

When current reaches a set of parallel branches, it splits in a fixed pattern set by the resistances. The current divider rule finds each branch's share directly, the parallel partner of the voltage divider rule.

How current splits

Current entering parallel branches divides among them, and three plain rules describe the split. Two equal resistors share the current equally. When the values differ, the smaller resistance takes the larger share. And the shares are in the inverse ratio of the resistances: if one branch has twice the resistance of another, it carries half the current. The reason is that every branch has the same voltage across it. With \(V\) fixed, Ohm's law gives \(I = V/R\), so doubling \(R\) halves \(I\). Current divides the way water does between a wide pipe and a narrow one joining the same two tanks.

Reasoning with ratios

Because each branch has the same voltage, \(I_1R_1 = I_2R_2 = \dots\), which gives \(I_1/I_2 = R_2/R_1\). Often this is all you need. Take three parallel branches of 2 kΩ, 4 kΩ and 8 kΩ, and suppose a meter shows 4 mA in the 2 kΩ branch. The 4 kΩ branch has twice the resistance, so it carries 2 mA. The 8 kΩ branch has four times the resistance, so it carries 1 mA. By Kirchhoff's current law, the total entering is \(4 + 2 + 1 = 7\,\text{mA}\). Not one actual voltage was needed, though you can check that each branch has 8 V across it.

The general rule

When you know the total current \(I\) entering parallel branches and their resistances, the current divider rule (CDR) gives any branch current. The shared voltage is \(V = IR_T\), where \(R_T\) is the total parallel resistance, and the branch current is \(I_x = V/R_x\). Together:

I_x = \frac{R_T}{R_x}I

In terms of conductance the rule reads more naturally, because each branch takes a share in proportion to how easily it conducts:

I_x = \frac{G_x}{G_T}I

The shares then add to the whole, since the \(G_x\) add to \(G_T\).

Two branches: the other resistor on top

For just two branches, substitute \(R_T = R_1R_2/(R_1 + R_2)\) into the general rule and \(R_1\) cancels:

I_1 = \frac{R_2}{R_1 + R_2}I \qquad I_2 = \frac{R_1}{R_1 + R_2}I

Notice two things. The numerator is the other resistor, not the one whose current you want, which is the reverse of the voltage divider rule. And the denominator is the plain sum of the two resistors, not their parallel combination. Both features follow from the inverse ratio: the branch facing the larger opposite resistor gets the larger share.

Worked example: two branches

A current of 40 mA enters \(R_1 = 1.2\,\text{k}\Omega\) and \(R_2 = 3.6\,\text{k}\Omega\) in parallel. 1. Sum of the resistors: \(4.8\,\text{k}\Omega\). 2. Current in \(R_1\): \(I_1 = \frac{3.6}{4.8}(40) = 30\,\text{mA}\). 3. Current in \(R_2\): \(I_2 = \frac{1.2}{4.8}(40) = 10\,\text{mA}\). 4. Check by KCL: \(30 + 10 = 40\,\text{mA}\). 5. Check the voltages: \((30\,\text{mA})(1.2\,\text{k}\Omega) = 36\,\text{V}\) and \((10\,\text{mA})(3.6\,\text{k}\Omega) = 36\,\text{V}\), equal as parallel branches must be. The 3:1 resistance ratio produced a 1:3 current ratio.

Worked example: three branches

A current of 60 mA enters three parallel resistors of 100 Ω, 150 Ω and 300 Ω. Find each branch current. 1. Conductances: 10.0 mS, 6.67 mS and 3.33 mS, so \(G_T = 20.0\,\text{mS}\) and \(R_T = 50\,\Omega\). 2. CDR: \(I_{100} = \frac{50}{100}(60) = 30\,\text{mA}\), \(I_{150} = \frac{50}{150}(60) = 20\,\text{mA}\), \(I_{300} = \frac{50}{300}(60) = 10\,\text{mA}\). 3. Check by KCL: \(30 + 20 + 10 = 60\,\text{mA}\). 4. Check by the conductance form: the 100 Ω branch has half of \(G_T\), so half the current. You could also combine two branches first and use the two-branch rule twice.

Worked example: choosing a resistor

A current of 20 mA must split so that 15 mA flows in \(R_1\), with \(R_2 = 3.3\,\text{k}\Omega\) in parallel. Find \(R_1\). 1. Rearranging the two-branch rule gives \(R_1 = R_2(I - I_1)/I_1\). 2. Substitute: \(R_1 = 3.3 \times 5/15 = 1.1\,\text{k}\Omega\), a standard value. 3. Second route, using KCL: \(I_2 = 20 - 15 = 5\,\text{mA}\), so the branch voltage is \((5\,\text{mA})(3.3\,\text{k}\Omega) = 16.5\,\text{V}\), and \(R_1 = 16.5\,\text{V}/15\,\text{mA} = 1.1\,\text{k}\Omega\). 4. Check: \(R_1\) is the smaller resistor, and it carries the larger share.

Quick fractions for estimates

A few patterns from the two-branch rule are worth knowing by heart, because they let you estimate a split in your head and catch errors. \(N\) equal branches each carry \(I/N\). If one resistor is twice the other, the smaller carries two thirds of the current and the larger one third. A ratio of 1 to 3 gives three quarters and one quarter, and a ratio of 1 to 9 gives 90% and 10%. In each case the smaller resistor's fraction is the larger resistor divided by their sum. If a calculated answer gives the larger resistor more than half the current, something has gone wrong.

Very unequal branches

When one branch is far smaller than the other, it takes almost all the current. With 10 Ω in parallel with 10 kΩ, the 10 Ω branch carries \(10{,}000/10{,}010\), about 99.9% of the total, and the 10 kΩ branch only about 0.1%. The large resistor still carries some current, so the saying that current takes the path of least resistance is only a rough guide: current takes every available path, in inverse proportion to resistance. A deliberate low-resistance branch, called a shunt, uses this to divert most of a large current around a delicate meter, as the topic Meter design and grounding explains.

Common mistakes to avoid

First, putting the branch's own resistor in the numerator of the two-branch rule; for \(I_1\) the numerator is \(R_2\). Second, using the parallel combination instead of the sum in the two-branch denominator. Third, applying the two-branch formula to three branches at once; use \(I_x = (R_T/R_x)I\), or combine branches first. Fourth, assuming the smallest resistor takes all the current, or that the split is equal because the voltages are equal. Fifth, forgetting to check that the branch currents add to the total.

Key takeaways

Current entering parallel branches divides in the inverse ratio of their resistances, because every branch has the same voltage: I₁/I₂ = R₂/R₁. Equal branches share equally, and the smaller resistance takes the larger share. General rule: I_x = (R_T/R_x) I, or I_x = (G_x/G_T) I. Two branches: I₁ = R₂I/(R₁ + R₂), with the other resistor on top and the plain sum below. To choose a resistor, R₁ = R₂(I − I₁)/I₁. Every branch carries some current, and the currents always add to the total.

Flashcards

Flashcard

Current divider rule

I_x = (R_T / R_x) I

R_T is the total parallel resistance.

Test your understanding

Question 1 of 5

A current of 48 mA enters a 1.0 kΩ resistor and a 2.2 kΩ resistor in parallel. What current flows in the 1.0 kΩ resistor?

Question 2 of 5

Two parallel branches are 2 kΩ and 6 kΩ. The 6 kΩ branch carries 1.5 mA. What does the 2 kΩ branch carry?

Question 3 of 5

A current of 90 mA enters parallel resistors of 220 Ω, 330 Ω and 660 Ω. What current flows in the 330 Ω resistor?

Question 4 of 5

A 10 Ω resistor is in parallel with a 10 kΩ resistor. Which statement about the current split is correct?

Question 5 of 5

A 30 mA current must split so that 20 mA flows in R1, with R2 = 2.0 kΩ in parallel. What value must R1 have?

← Previous topicNext topic →