Electrical Engineering › Section D · Parallel and series-parallel circuits › Topic D.2
Kirchhoff's current law
Whatever current flows into a junction must flow out again. Kirchhoff's current law turns that bookkeeping into equations that find unknown currents anywhere in a network, even inside a sealed chip you cannot see into.
Current in equals current out
Kirchhoff's voltage law balances voltages around loops. His current law, stated in about 1845 alongside the voltage law, balances currents at junctions. Kirchhoff's current law (KCL) says that the algebraic sum of the currents at any node is zero. Put more plainly, the total current flowing into a node equals the total flowing out:
The reason is conservation of charge. An ideal node is just a connection with no room to store charge, so every coulomb that arrives each second must leave in the same second. If 3 A and 2 A flow into a node that has one other wire, that wire carries 5 A out.
Nodes, regions and signs
A node is any point where two or more elements join, together with the wires that connect them at one potential. KCL applies to each node, and also to any closed boundary you draw around part of a circuit, a whole board or a complete system: current crossing inward equals current crossing outward. To write the equation, picture standing on the node. An arrow pointing towards you is a current entering; an arrow pointing away is leaving. If you prefer the zero-sum form, count entering currents as positive and leaving ones as negative, or the reverse, but use one choice for the whole equation.
Worked example: one unknown at a node
Four wires meet at node b. A current of 2.5 mA flows in on the first, 1.2 mA flows out on the second and 4.0 mA flows out on the third. Find the current in the fourth wire. 1. Total known in: 2.5 mA. Total known out: \(1.2 + 4.0 = 5.2\,\text{mA}\). 2. More leaves than arrives, so the fourth wire must bring current in. 3. KCL: \(2.5 + I_4 = 5.2\), so \(I_4 = 2.7\,\text{mA}\), flowing into node b. 4. Check: in \(2.5 + 2.7 = 5.2\,\text{mA}\), out 5.2 mA. Deciding the direction first, by comparing the totals, avoids most sign errors.
Assumed directions
In a larger network you often cannot tell in advance which way a current flows. Mark an arrow for each unknown current, choosing any direction, and write KCL using those arrows. If a result comes out negative, its size is right and the actual current flows against the arrow. As with KVL, a negative answer is information, not an error, so carry the sign rather than flipping arrows part way through. When several unknowns meet, start at a node with only one unknown, solve it, and carry the result to the next node. A node with two unknowns cannot be solved from its own equation alone.
KCL explains series and parallel
KCL gives the current rules of series and parallel circuits. At a node joining only two elements, one current enters and one leaves, so the two must be equal: series elements carry the same current. At the top node of a parallel circuit, the source current enters and the branch currents leave, so \(I_s = I_1 + I_2 + \dots + I_N\), exactly the result found in Parallel elements, total conductance, and resistance. In that topic's 24 V example, 0.333 A entered the top node and \(0.200 + 0.133 = 0.333\,\text{A}\) left through the two resistors.
Worked example: a network of three nodes
A supply delivers 50 mA into node a and takes it back from ground, node 0. \(R_1\) runs from a to b and \(R_2\) from a to c. \(R_3\) runs from b to ground, \(R_4\) from b to c, and \(R_5\) from c to ground. Meters show 30 mA in \(R_1\) (a to b) and 18 mA in \(R_3\) (b to ground). 1. Node a: \(50 = 30 + I_2\), so \(I_2 = 20\,\text{mA}\) from a to c. 2. Node b: \(30 = 18 + I_4\), so \(I_4 = 12\,\text{mA}\) from b to c. 3. Node c: \(I_5 = 20 + 12 = 32\,\text{mA}\) down to ground. 4. Check at ground: \(18 + 32 = 50\,\text{mA}\) returns to the supply.
KCL on a closed boundary
KCL does not need you to know what is inside a region. Draw a boundary round an integrated circuit and list every current crossing it. Suppose 15 mA, 3 mA and 0.5 mA flow into a chip's pins and 12 mA and 4.5 mA flow out of two others, with one pin unmeasured. Total in is 18.5 mA and total out is 16.5 mA, so the last pin must carry 2.0 mA out. The same idea checked the network example: a boundary around the whole network had 50 mA entering at a and 50 mA leaving to ground.
How many equations?
If a circuit has \(n\) nodes, counting the reference node, you can write \(n\) KCL equations, but only \(n - 1\) of them are independent. The last one is always the sum of the others, so it adds no new information and serves only as a check. In the three-node example there were four nodes in all, counting ground, so three independent equations fixed the three unknown currents, and the equation at ground merely confirmed them. Choosing \(n - 1\) nodes and writing KCL at each is the starting point of Nodal analysis, later in the course.
Common mistakes to avoid
First, writing a current as entering in one part of an equation and leaving in another: choose a direction for each arrow and keep it. Second, starting at a node with two unknowns, which leaves you stuck. Third, thinking current is used up by loads; every ampere that enters a resistor leaves it, and only energy is converted. Fourth, writing KCL at every node and expecting new information from the last one. Fifth, dropping a negative sign instead of reading it as a reversed direction.
Key takeaways
KCL, from Kirchhoff in about 1845: the currents entering a node, region or system equal the currents leaving, because charge is conserved and cannot pile up at a node. Picture standing on the node to judge in and out. Assume directions for unknowns; a negative result means the current flows the other way. Start at nodes with one unknown. KCL explains why series elements share one current and why parallel branch currents add to the source current. A circuit with n nodes gives n − 1 independent KCL equations.
Flashcards
Flashcard
Current into a node equals current out of it
Test your understanding
Question 1 of 5
Currents of 6 mA and 3.5 mA flow into a node and 7 mA flows out on a third wire. What does the fourth and last wire carry?
Question 2 of 5
Why does Kirchhoff's current law hold?
Question 3 of 5
A source sends 0.90 A into three parallel branches. Two of them carry 0.25 A and 0.40 A. What does the third carry?
Question 4 of 5
You assumed an unknown current flows into a node, and KCL gives −3 mA. What is actually happening?
Question 5 of 5
A circuit has five nodes, including the ground node. How many independent KCL equations can be written?
