Electrical Engineering › Section A · Introduction, current, and voltage › Topic A.4

Semiconductors

Between conductors and insulators sits a small family of materials whose conductivity can be changed by heat, by light and, above all, by adding tiny traces of other elements. That controllability makes semiconductors the foundation of every diode, transistor and chip.

Neither conductor nor insulator

A semiconductor conducts far better than an insulator but far worse than a metal. What makes it valuable is not its conductivity itself but how easily that conductivity can be changed. A copper wire's conductivity changes only modestly with conditions, and a glass rod barely conducts at all. A sliver of silicon, by contrast, can be made a thousand or a million times more conductive by adding a trace of impurity, and it responds strongly to temperature and to light. Electronic devices exploit exactly this: a diode or transistor is a carefully arranged pattern of semiconductor regions with different conductivities.

The semiconductor materials

The two classic elemental semiconductors, silicon (Si) and germanium (Ge), sit in group 14 of the periodic table and have four valence electrons. In a pure crystal each atom shares those four electrons with four neighbours in covalent bonds, which ties nearly all of them in place. Germanium was used in the first transistor of 1947, but silicon took over in the 1960s: it tolerates higher temperatures, it is abundant in ordinary sand, and its oxide forms an excellent insulating layer on a chip. Compound semiconductors combine two elements: gallium arsenide (GaAs) for radio-frequency circuits, gallium nitride (GaN) for compact chargers and LEDs, and silicon carbide (SiC) for electric-vehicle power converters.

Few free carriers in a pure crystal

Because the covalent bonds hold the valence electrons, a pure, or intrinsic, silicon crystal at room temperature has only about \(1 \times 10^{16}\) free electrons per cubic metre. Copper, as the topic "Atoms, current, and voltage" showed, has about \(8.5 \times 10^{28}\). Each free electron in silicon also leaves behind a gap in a bond that can carry current too, but even counting both, pure silicon is a poor conductor. An electron must gain a definite amount of energy, about 1.1 eV in silicon and 0.66 eV in germanium, to break free; "Quantum physics, crystal structure, and band theory" explains where these energy gaps come from.

Worked example: comparing free electrons

How many times more free electrons does copper have than pure silicon at room temperature? 1. Copper: about \(8.5 \times 10^{28}\) per m³. 2. Intrinsic silicon: about \(1.0 \times 10^{16}\) per m³. 3. Ratio:

\frac{8.5 \times 10^{28}}{1.0 \times 10^{16}} = 8.5 \times 10^{12}

Dividing powers of ten subtracts the exponents, \(28 - 16 = 12\). 4. Interpret: copper has roughly eight and a half million million times as many free electrons in each cubic metre. 5. Check the conclusion: pure silicon is not useful as a wire, and its value lies in how far that tiny number can be raised on purpose.

Heat raises conductivity

In a metal, heating makes the lattice vibrate more and gets in the way of the free electrons, so resistance rises. A semiconductor behaves the opposite way. Heat supplies the energy that breaks electrons out of their bonds, so the number of free carriers climbs steeply and the resistance falls. A material whose resistance decreases as temperature rises is said to have a negative temperature coefficient. This is useful in temperature sensors, but it is also a hazard: a hot semiconductor device conducts more, which can make it hotter still. Germanium, with its smaller energy gap, is more sensitive to heat than silicon, one reason silicon replaced it.

Worked example: a warming sensor

A chip of nearly pure silicon is used as a sensor and warms from 25 °C to 75 °C. Predict what happens to its resistance. 1. Identify the material: silicon is a semiconductor, not a metal. 2. Mechanism: the extra heat gives more valence electrons the 1.1 eV or so they need to break free. 3. Size of the effect: for pure silicon, the standard estimate puts the rise in free carriers over this range at more than twentyfold. 4. Consequence: with many more carriers, the resistance falls sharply. 5. Contrast: a copper wire over the same range would see its resistance rise by about a fifth, the effect quantified in "Temperature effects and superconductors". Opposite trends are a quick way to tell the two kinds of material apart.

Light raises conductivity too

Light carries energy in packets called photons. When a photon with enough energy strikes a semiconductor, it can break an electron free from its bond, just as heat does. More light therefore means more free carriers and lower resistance. Photoconductive cells use this to make light sensors whose resistance falls in bright light. Solar cells and photodiodes use a related effect to turn light directly into a voltage or a current. LEDs run the process in reverse, releasing light when carriers recombine; GaAs and GaN compounds are favoured for this because silicon is a poor light emitter. "Special-purpose diodes: LEDs, photodiodes, Schottky, and others" covers these devices.

Purity and doping

Semiconductor manufacture starts with extreme purity: electronic-grade silicon is better than 99.9999999% pure, often called "nine nines". Then specific impurities are added deliberately, a process called doping. Adding atoms with five valence electrons, such as phosphorus, supplies spare free electrons and makes n-type silicon. Adding atoms with three, such as boron, creates missing-electron sites and makes p-type silicon. Even one impurity atom per ten million silicon atoms changes the conductivity enormously. Joining p-type and n-type regions creates the junctions inside diodes and transistors, which "Electrons, holes, the P-N junction, and junction diodes" develops in full.

Worked example: the power of doping

Silicon has about \(5.0 \times 10^{28}\) atoms per m³. It is doped with phosphorus at one atom per \(10^{7}\) silicon atoms, and each phosphorus atom frees one electron. 1. Donor atoms per m³: \(\frac{5.0 \times 10^{28}}{10^{7}} = 5.0 \times 10^{21}\). 2. Free electrons now: about \(5.0 \times 10^{21}\) per m³, since the intrinsic \(1 \times 10^{16}\) is negligible beside it. 3. Increase:

\frac{5.0 \times 10^{21}}{1.0 \times 10^{16}} = 5.0 \times 10^{5}

4. Interpret: replacing one atom in ten million raises the free-electron count about 500,000 times. 5. Check: the doped silicon still has about \(10^{7}\) times fewer free electrons than copper, so it remains a semiconductor.

Common mistakes to avoid

First, assuming semiconductors behave like metals when heated: their resistance usually falls, not rises. Second, thinking a semiconductor is simply a poor conductor; its defining feature is controllable conductivity. Third, believing doping adds a lot of material: the impurity level is typically parts per million or less. Fourth, forgetting that silicon has four valence electrons, while n-type and p-type dopants have five and three. Fifth, treating light-sensitive and heat-sensitive behaviour as separate mysteries; both come from energy freeing electrons from their bonds.

Key takeaways

Semiconductors lie between conductors and insulators, and their conductivity can be changed by temperature, light and doping. Silicon and germanium have four valence electrons bound in covalent bonds, so pure crystals have few free carriers: about 10¹⁶ per m³ in silicon against 8.5 × 10²⁸ in copper. Silicon dominates; GaAs, GaN and SiC serve radio, lighting and power uses. Semiconductors have a negative temperature coefficient: resistance falls as they warm. Light frees carriers too. Doping at around one part in ten million with phosphorus or boron gives n-type or p-type silicon.

Flashcards

Flashcard

Semiconductor

A material between conductor and insulator whose conductivity can be controlled

By heat, light and doping.

Test your understanding

Question 1 of 5

A small piece of pure silicon is heated from room temperature. What happens to its resistance?

Question 2 of 5

How many valence electrons does a silicon atom have?

Question 3 of 5

Silicon has 5.0 × 10²⁸ atoms per m³. It is doped at one phosphorus atom per 10⁸ silicon atoms. About how many phosphorus atoms are there per m³?

Question 4 of 5

Which of these is a compound semiconductor?

Question 5 of 5

Why does a photoconductive cell's resistance fall in bright light?

← Previous topicNext topic →