Electrical Engineering › Section J · Series, parallel, and series-parallel ac circuits › Topic J.2
Frequency response of the R-C circuit
Keep the components fixed and sweep the source frequency, and a simple resistor-capacitor circuit changes character completely, from almost pure capacitance to almost pure resistance. That shift is the seed of every filter, tone control and coupling network you will meet.
One circuit, many frequencies
So far each ac circuit has been solved at a single frequency, but an audio signal spans roughly 20 Hz to 20 kHz. Resistance does not depend on frequency; capacitive reactance does, so the impedance, the current and every voltage in an R-C circuit change with frequency. The frequency response of a circuit is that dependence, usually plotted as a magnitude and an angle against frequency. This topic studies a resistor and capacitor in series, driven by a source of fixed rms voltage E.
How each element responds
On a graph against frequency, R is a horizontal line. The capacitive reactance \(X_C = 1/(2\pi fC)\) falls as frequency rises: doubling the frequency halves it. At very low frequency \(X_C\) is huge and the capacitor is close to an open circuit, which matches its dc behaviour in a steady state. At very high frequency \(X_C\) is tiny and the capacitor is close to a short circuit. Somewhere between, the two curves cross. Below the crossing the capacitor dominates the series impedance; above it the resistor does.
The crossover frequency
The two curves cross where \(X_C = R\). Setting \(1/(2\pi f_1 C) = R\) and solving gives
At this frequency the series impedance is \(Z_T = R - jR\), so its magnitude is \(\sqrt{2}R\) and its angle is exactly −45°. The frequency \(f_1\) is also called the corner, cutoff or break frequency, names used again in the topic "R-C low-pass and high-pass filters", where the response is drawn on a logarithmic frequency axis. Notice that \(f_1\) depends only on the product RC, the same time constant τ that governed charging transients, with \(f_1 = 1/(2\pi\tau)\).
Impedance against frequency
At any frequency the series impedance is
As f rises from zero, the magnitude falls from very large values towards R, never below it. The angle moves from close to −90°, an almost purely capacitive circuit, through −45° at \(f_1\), towards 0°, an almost purely resistive one. Because the angle is always negative, the source current always leads the source voltage, but by less and less as the frequency rises. The current magnitude \(E/|Z_T|\) therefore rises with frequency towards \(E/R\).
Worked example: a frequency sweep
A 12 V source drives a 2.2 kΩ resistor in series with a 0.047 µF capacitor. Tabulate the response. 1. Corner: \(f_1 = 1/(2\pi \times 2200 \times 0.047\,\mu\text{F}) = 1.54\) kHz. 2. At each frequency find \(X_C\), then \(Z_T\), then \(V_C = E X_C/|Z_T|\) (the divider rule, magnitudes only). 3. Results, with f in Hz, \(|Z_T|\) in kΩ and \(V_C\) in volts:
4. Check: at \(f_1\), \(|Z_T| = \sqrt{2} \times 2.2 = 3.11\) kΩ and \(V_C = 12/\sqrt{2} = 8.49\) V, as predicted.
The capacitor voltage
The voltage across the capacitor is the output most often taken from this circuit. By the voltage divider rule,
At low frequency \(X_C\) is much larger than R, so almost all of E appears across the capacitor, nearly in phase with it. At \(f_1\), \(V_C = 0.707E\) and lags E by 45°. At high frequency the capacitor behaves almost like a short, so \(V_C\) falls towards zero and its lag approaches 90°. A circuit connected across the capacitor therefore receives low frequencies well and has high frequencies largely shorted out: the action of a low-pass filter.
The resistor voltage and the current
The resistor voltage does the opposite. It is in phase with the current, so it leads E by the same angle as the current does, and its magnitude \(V_R = ER/|Z_T|\) rises from almost zero towards E as frequency increases. In the sweep above it is 0.778 V at 100 Hz and 12.0 V at 20 kHz. At every frequency \(\mathbf{V}_R\) and \(\mathbf{V}_C\) are 90° apart, so
even though \(V_R + V_C\) is usually more than E. Taking the output across the resistor instead of the capacitor gives a high-pass response, which passes high frequencies and blocks low ones.
Worked example: choosing a capacitor
A designer needs the crossover of a series R-C circuit near 1 kHz, using a 10 kΩ resistor. 1. Rearrange the corner formula: \(C = 1/(2\pi f_1 R)\). 2. Substitute: \(C = 1/(2\pi \times 1000 \times 10\,000) = 15.9\) nF. 3. Choose a standard value: 15 nF is the nearest E12 value. 4. Recalculate: with 15 nF, \(f_1 = 1/(2\pi \times 10\,000 \times 15\,\text{nF}) = 1.06\) kHz, about 6% high, which is usually close enough given that capacitors often have tolerances of 5 to 10%. 5. Check: at 1.06 kHz, \(X_C = 10.0\) kΩ equals R, as the definition of \(f_1\) requires.
The series R-L circuit by analogy
A resistor in series with an inductor behaves as a mirror image. Inductive reactance \(X_L = 2\pi fL\) rises with frequency, so the crossover where \(X_L = R\) is
Below \(f_1\) the circuit is mainly resistive; above it, mainly inductive. The impedance magnitude rises from R towards large values and its angle climbs from 0° towards +90°, with the current lagging. The inductor voltage rises towards E with frequency, while the resistor voltage falls. For R = 1 kΩ and L = 0.1 H, \(f_1 = 1.59\) kHz, and at that frequency \(V_L = V_R = 0.707E\).
Summary: series ac circuits
The same current flows through every element. The total impedance is the complex sum of the element impedances, and it is inductive or capacitive according to which reactance is larger. Kirchhoff's voltage law holds for phasors. The resistor voltage is in phase with the current, the inductor voltage leads it by 90° and the capacitor voltage lags it by 90°. The power factor \(\cos\theta_T = R/|Z_T|\) is closer to 1 the more the resistance dominates the net reactance. And at a fixed source voltage, every one of these quantities may change with frequency.
Common mistakes to avoid
1. Leaving out the 2π: \(1/(RC)\) is the corner in radians per second, not hertz. 2. Expecting \(V_C = E/2\) at the corner: it is \(E/\sqrt{2}\), or 0.707E. 3. Thinking the impedance can fall below R: in series it approaches R from above. 4. Adding \(V_R\) and \(V_C\) arithmetically instead of using \(V_R^2 + V_C^2 = E^2\). 5. Confusing the two outputs: across the capacitor the response is low-pass, across the resistor it is high-pass. 6. Using the R-C formula for an R-L circuit: there \(f_1 = R/(2\pi L)\).
Key takeaways
A capacitor's reactance falls as frequency rises, so a series R-C circuit moves from capacitive at low frequency to resistive at high frequency. The crossover \(f_1 = 1/(2\pi RC)\) is where \(X_C = R\), \(|Z_T| = \sqrt{2}R\) and the angle is −45°. The capacitor voltage falls from E towards zero, passing \(0.707E\) at \(f_1\); the resistor voltage rises from zero towards E, and \(V_R^2 + V_C^2 = E^2\) throughout. The series R-L circuit mirrors this, with \(f_1 = R/(2\pi L)\) and an angle climbing towards +90°.
Flashcards
Flashcard
How a circuit's impedance, currents and voltages change with source frequency
Test your understanding
Question 1 of 5
A 1.0 kΩ resistor is in series with a 0.10 µF capacitor. At what frequency does X_C equal R?
Question 2 of 5
A 10 V source drives a series R-C circuit at its crossover frequency f₁. What is the rms voltage across the capacitor?
Question 3 of 5
A series R-C circuit is driven at twice its crossover frequency. What is the angle of its total impedance?
Question 4 of 5
What happens to a series R-C circuit as the frequency rises far above f₁?
Question 5 of 5
A 470 Ω resistor is in series with a 10 mH inductor. At what frequency does X_L equal R?
