Electrical Engineering › Section D · Parallel and series-parallel circuits › Topic D.1

Parallel elements, total conductance, and resistance

Connect elements side by side between the same two points and they all get the same voltage. Parallel connections are how homes, vehicles and circuit boards feed many loads from one supply, and they combine by adding conductances rather than resistances.

What makes elements parallel

Two elements, branches or whole networks are in parallel when they have two points in common. Each is connected directly between the same pair of nodes, so each has exactly the same voltage across it. That is the test to use: if two elements must have identical voltage because they join the same two nodes, they are in parallel. The outlets in a home are wired this way, so every appliance receives the full supply voltage and can be switched on or off without affecting the others. Contrast this with series elements, which share one point and carry the same current.

Recognising parallel connections

Parallel elements can be drawn in many ways: side by side like ladder rungs, fanned out from one junction, or with the top and bottom wires squared off so the shared nodes are less obvious. Label the nodes and the question becomes simple. Do both ends of the two elements land on the same pair of nodes? If one element runs from node a to node b and another also runs from a to b, they are in parallel, however the drawing looks. Groups combine too: two resistors in series between a and c, with a third resistor from a to c, form a series pair in parallel with the third.

Total conductance and resistance

Conductance, \(G = 1/R\) in siemens, measures how easily a branch passes current. In parallel, conductances simply add:

G_T = G_1 + G_2 + \dots + G_N

Since \(G = 1/R\), the total resistance follows from

\frac{1}{R_T} = \frac{1}{R_1} + \frac{1}{R_2} + \dots + \frac{1}{R_N}

This formula gives \(1/R_T\), not \(R_T\), so the last step is always to take the reciprocal. Every branch added gives the current another path, so \(G_T\) rises and \(R_T\) falls, which is the opposite of adding resistors in series.

Worked example: three resistors in parallel

Find the total resistance of 100 Ω, 220 Ω and 470 Ω in parallel. 1. Conductances: \(G_1 = 10.0\,\text{mS}\), \(G_2 = 4.545\,\text{mS}\), \(G_3 = 2.128\,\text{mS}\). 2. Sum: \(G_T = 16.67\,\text{mS}\). 3. Reciprocal: \(R_T = 1/G_T = 59.98\,\Omega\), about 60.0 Ω. 4. Check: the answer is below 100 Ω, the smallest resistor, as it must be. 5. A second route: combine two at a time with the product-over-sum rule on the next card, \(100 \parallel 220 = 68.75\,\Omega\), then \(68.75 \parallel 470 = 59.98\,\Omega\), the same result.

Shortcuts for common cases

For two resistors, the reciprocal formula simplifies to product over sum:

R_T = \frac{R_1R_2}{R_1 + R_2}

For \(N\) equal resistors \(R\), it becomes \(R_T = R/N\), and \(G_T = NG\): four 2.2 kΩ resistors in parallel give 550 Ω. For three resistors there is a product form,

R_T = \frac{R_1R_2R_3}{R_1R_2 + R_1R_3 + R_2R_3}

but most engineers simply apply product over sum twice. The symbol \(\parallel\) is shorthand for "in parallel with", so \(R_1 \parallel R_2\) means the parallel combination. Order does not matter: parallel elements can be interchanged without changing \(R_T\).

Always below the smallest

A parallel group always has less resistance than its smallest member, because every branch adds conductance. When the values are far apart, the total lies close to the smaller one: 1 kΩ in parallel with 100 kΩ gives 990 Ω. This works in both directions. Two 47 Ω resistors in parallel give 23.5 Ω. Add a 10 kΩ resistor across them and the total barely moves, to 23.44 Ω. Add a 1 Ω resistor instead and the total collapses to about 0.959 Ω. Either way the total decreases, however large or small the new branch.

Designing for a target resistance

Suppose you have \(R_1\) and need a total \(R_T\). Solve product over sum for the second resistor:

R_2 = \frac{R_1R_T}{R_1 - R_T}

The target must be smaller than \(R_1\), since paralleling can only lower resistance. For example, with a 1.5 kΩ resistor in hand and 1.0 kΩ needed, \(R_2 = (1.5)(1.0)/(1.5 - 1.0) = 3.0\,\text{k}\Omega\), a standard value. Check: \((1.5)(3.0)/(4.5) = 1.0\,\text{k}\Omega\). The same idea creates values not sold off the shelf, as two 1 kΩ resistors in parallel make 500 Ω.

The parallel circuit with a source

Connect a source \(E\) across parallel resistors and every branch has \(V = E\). Each branch current is then \(I_k = E/R_k\), so the smallest resistor carries the largest current. Multiply \(1/R_T = 1/R_1 + 1/R_2\) through by \(E\) and you find \(E/R_T = E/R_1 + E/R_2\). In words, for a single-source parallel network, the source current is the sum of the branch currents: \(I_s = I_1 + I_2 + \dots\). Power works as before: each branch absorbs \(P_k = E^2/R_k\), and the source delivers \(EI_s\), equal to the total.

Worked example: two loads on 24 V

A 24 V source supplies \(R_1 = 120\,\Omega\) and \(R_2 = 180\,\Omega\) in parallel. 1. Total: \(R_T = (120)(180)/300 = 72\,\Omega\). 2. Source current: \(I_s = 24/72 = 0.333\,\text{A}\). 3. Branch currents: \(I_1 = 24/120 = 0.200\,\text{A}\) and \(I_2 = 24/180 = 0.133\,\text{A}\). 4. Check: \(0.200 + 0.133 = 0.333\,\text{A}\). 5. Powers: \(P_1 = 24^2/120 = 4.8\,\text{W}\) and \(P_2 = 3.2\,\text{W}\), while the source delivers \(24 \times 0.333 = 8.0\,\text{W}\). In parallel, the smaller resistor dissipates more, the reverse of series.

Parallel in practice

Parallel connection is the standard way to feed loads. Every appliance in a home sees the full 120 V and works independently, but each one switched on adds a branch, lowers the total resistance and raises the supply current, which is why too many heaters on one circuit trip its breaker. Paralleled resistors also share power: two equal resistors in parallel each dissipate half the total, so two 0.25 W parts can together handle 0.5 W. And a combination of standard values gives resistances that are not available on their own.

Common mistakes to avoid

First, forgetting the final reciprocal: \(1/R_1 + 1/R_2\) is \(1/R_T\), not \(R_T\). Second, using product over sum for three resistors at once; it works only for two at a time. Third, expecting a large resistor added in parallel to raise the total; any added branch lowers it. Fourth, calling elements parallel because they look side by side, when they do not share both nodes. Fifth, getting a total larger than the smallest resistor, which always signals an arithmetic slip.

Key takeaways

Elements are in parallel when they share two points, so they have the same voltage. Conductances add, G_T = G₁ + G₂ + … + G_N, and 1/R_T = 1/R₁ + 1/R₂ + …; take the reciprocal at the end. Two resistors: R₁R₂/(R₁ + R₂). N equal resistors: R/N. R_T is always below the smallest branch and falls with every branch added. With a source, each branch current is E/R_k, the source current is their sum, and the smallest resistor takes the most current and power.

Flashcards

Flashcard

Parallel elements

Elements with two points in common

So they have the same voltage.

Test your understanding

Question 1 of 5

What is the total resistance of 12 Ω and 6 Ω in parallel?

Question 2 of 5

Resistors of 200 Ω, 400 Ω and 400 Ω are connected in parallel. What is the total resistance?

Question 3 of 5

A 10 kΩ resistor is added in parallel with a 470 Ω resistor. What happens to the total resistance?

Question 4 of 5

An 18 V source supplies 60 Ω and 90 Ω resistors connected in parallel. What current does the source deliver?

Question 5 of 5

You have a 1.2 kΩ resistor and need a total of 800 Ω. What resistor must be placed in parallel with it?

← Previous topicNext topic →