Electrical Engineering › Section C · Series circuits › Topic C.2
Kirchhoff's voltage law
Walk around any closed loop in a circuit and you arrive back at the potential you started from. Kirchhoff's voltage law turns that simple fact into an equation that finds unknown voltages, often without knowing a single resistance.
The law and why it holds
The German physicist Gustav Kirchhoff stated two circuit laws in about 1845, while still a student. His voltage law (KVL) says that, around any closed loop, the rises and drops in potential add algebraically to zero:
The reason is conservation of energy. Potential is energy per unit charge, and a charge carried once round a loop ends at the very point it left, with the same potential. Whatever energy it gained crossing sources must therefore equal what it lost crossing everything else. An equivalent form says the sum of the rises equals the sum of the drops.
Loops and directions
A closed loop is any path you can trace from a point back to that same point without leaving the circuit. To apply KVL, pick a start and a direction, then keep going until you are back. This course goes clockwise, but anticlockwise gives the same answers if the signs are applied correctly. Write a plus sign for a rise, where you pass from the minus marking to the plus marking, and a minus sign for a drop, from plus to minus. In a series circuit with one source, going round with the current gives \(E - V_1 - V_2 = 0\), so \(E = V_1 + V_2\).
Polarity, not element type
When you add up a loop, only the polarity you meet matters, not whether the element is a source or a resistor. Passing through a battery from its positive terminal to its negative one is a drop, written with a minus sign, exactly like crossing a resistor in the direction of its current. This is how KVL handles circuits with several sources, some aiding and some opposing. It also means you can find an unknown voltage directly from the others in the loop, with no need for the current or the resistance values.
Worked example: a missing voltage
A single loop contains, in clockwise order from node 0: a 24 V source \(E_1\) entered at its negative terminal, a resistor \(R_1\), a resistor \(R_2\), and a 6 V source \(E_2\) entered at its positive terminal. A meter shows 7.5 V across \(R_2\), positive on the side the loop reaches first. Find \(V_1\), the voltage across \(R_1\). 1. Clockwise from node 0: rise of 24 V, drop \(V_1\), drop of 7.5 V, drop of 6 V. 2. KVL: \(24 - V_1 - 7.5 - 6 = 0\). 3. Solve: \(V_1 = 10.5\,\text{V}\). 4. Check: drops \(10.5 + 7.5 + 6 = 24\,\text{V}\) match the rise. No resistance value was needed.
Voltage across a gap
KVL does not need a current-carrying path. A loop may cross an open gap between two points, and the gap's voltage is simply one more term. Join the negative terminals of a 12 V battery and a 9 V battery, and leave their positive terminals, a and b, unconnected. Going from a across the gap to b, down through the 9 V battery and up through the 12 V battery back to a: \(-V_{ab} - 9 + 12 = 0\), so \(V_{ab} = 3\,\text{V}\), with a the more positive. No current flows, yet a meter across the gap reads 3 V.
When the polarity is unknown
Often you do not know which end of an element is positive. Assume a polarity, mark it, and apply KVL as usual. If the answer comes out positive, the guess was right. If it comes out negative, the size is right and the true polarity is the reverse of the one you marked. A negative result is information, not an error, so keep the sign. Mesh analysis, later in the course, relies on exactly this habit of assuming directions and letting the signs report back.
Worked example: a negative answer
A loop contains, clockwise: a 9 V source entered at its negative terminal, a resistor dropping 5 V, an element X with an assumed polarity of plus on the side the loop enters, and a 12 V source entered at its positive terminal. Find \(V_x\). 1. Terms in order: \(+9\), \(-5\), \(-V_x\), \(-12\). 2. KVL: \(9 - 5 - V_x - 12 = 0\). 3. Solve: \(V_x = -8\,\text{V}\). 4. Interpret: X has 8 V across it, but its far side is the positive one. 5. Check with the true polarity, now a rise: \(9 - 5 + 8 - 12 = 0\).
KVL with Ohm's law
When the voltages are unknown but the resistances are known, write each resistor drop as \(IR\) and KVL becomes an equation for the current. Take a loop with a 12 V source, \(R_1 = 1.2\,\text{k}\Omega\), a 4.5 V source turned to oppose the first, and \(R_2 = 1.3\,\text{k}\Omega\). Clockwise with the current:
so \(I = 7.5/2500 = 3.0\,\text{mA}\). The drops are 3.6 V and 3.9 V, and \(12 - 3.6 - 4.5 - 3.9 = 0\) confirms it. The 12 V source delivers 36 mW, which equals the 13.5 mW the opposing source absorbs plus 10.8 mW and 11.7 mW in the resistors.
Interchanging series elements
Because every element of a series loop carries the same current, you may reorder them without changing the total resistance, the current, or any element's voltage and power. KVL is only a sum, and the order of the terms does not matter. This is useful when a loop mixes sources and resistors: redraw it with all the sources together, combine them into one net source, and solve a plain series circuit. It also explains why a meter across one resistor reads the same wherever that resistor sits in the string.
Where KVL applies
KVL is exact for lumped circuits, in which the parts are so small compared with the wavelength of the signals that changes reach every point effectively at once. At 60 Hz the wavelength is about 5,000 km, so ordinary circuits qualify easily. The law can fail when a changing magnetic field links the loop, or at very high frequencies over long conductors, where electromagnetic field models take over; the topic Time-varying fields, electromagnetic induction, and Faraday's law returns to this. For every dc circuit in this course, KVL holds around every loop, including loops that cross open gaps.
Common mistakes to avoid
First, mixing directions part way round a loop: choose clockwise or anticlockwise and keep it. Second, giving every source a plus sign; a source crossed from plus to minus is a drop. Third, dropping a negative answer's sign, which loses the true polarity. Fourth, believing a voltage needs a current, so that an open gap must read 0 V; the gap in the two-battery example has 3 V across it. Fifth, stopping before you are back at the starting point, which leaves a term out of the sum.
Key takeaways
KVL, from Kirchhoff in about 1845: the algebraic sum of rises and drops around any closed loop is zero, because energy is conserved. Pick a direction, write + for a rise (− to +) and − for a drop (+ to −), and judge by polarity, not element type. In a single-source series loop, E equals the sum of the drops. Assume unknown polarities; a negative result means reverse them. Loops may cross open gaps. Series elements can be reordered freely. KVL holds exactly for lumped circuits.
Flashcards
Flashcard
Around any closed loop, rises and drops add algebraically to zero
Test your understanding
Question 1 of 5
A loop has an 18 V source and three resistors. Two of the resistors drop 4.7 V and 6.1 V. What is the voltage across the third resistor?
Question 2 of 5
Applying KVL with an assumed polarity for an element gives Vx = −8 V. What does this mean?
Question 3 of 5
The negative terminals of a 12 V battery and a 9 V battery are joined, and their positive terminals a and b are left open. What is V_ab?
Question 4 of 5
Going clockwise round a loop, you pass through a 5 V source from its + terminal to its − terminal. How does it enter the KVL sum?
Question 5 of 5
A loop holds a 20 V source, a 2.2 kΩ resistor, a 5 V source that opposes the first, and a 3.3 kΩ resistor. What current flows?
