Electrical Engineering › Section D · Parallel and series-parallel circuits › Topic D.7
Loaded voltage dividers and potentiometers
The voltage divider rule gives the right answer only while nothing draws current from the divider. Connect a load and the output sags. This topic shows how much it sags, how to design a divider for known loads and how to keep a potentiometer in control.
When the divider has to do work
In "The voltage divider rule and notation" every divider was unloaded: its output terminals fed nothing. Real dividers exist to feed something, such as a sensor input, a bias point or a lower supply rail. A load connected to a tap is a resistance in parallel with the part of the divider below that tap, so it changes the very ratio that set the voltage. The result is a series-parallel network, solved with the reduce and return method from "Series-parallel and ladder networks". The central idea of this topic is simple: the less current the loads draw compared with the current in the divider itself, the closer the outputs stay to their no-load values.
A divider supply with several taps
One source and a resistor chain can supply several voltages. Take 24 V across \(R_1 = 1.0\,\text{k}\Omega\) from node a (24 V) to node b, \(R_2 = 2.2\,\text{k}\Omega\) from b to c and \(R_3 = 1.8\,\text{k}\Omega\) from c to ground. Unloaded, 4.8 mA flows down the chain, and the divider rule gives
The top tap, a, is the source itself, so a load there leaves its voltage unchanged. Loads at b and c are another matter, because each sits in parallel with part of the chain.
Worked example: loading the taps
Connect a 2.2 kΩ load from b to ground and another from c to ground. 1. At the bottom, \(R_3 \parallel 2.2\,\text{k}\Omega = \frac{1.8 \times 2.2}{4.0} = 0.990\,\text{k}\Omega\). 2. Add \(R_2\): \(3.19\,\text{k}\Omega\). In parallel with the load at b: \(\frac{3.19 \times 2.2}{5.39} = 1.302\,\text{k}\Omega\). 3. Divider rule at b: \(V_b = 24 \times \frac{1.302}{1.0 + 1.302} = 13.6\,\text{V}\). 4. Divider rule from b down to c: \(V_c = 13.6 \times \frac{0.990}{3.19} = 4.21\,\text{V}\). 5. Compare: the taps fell from 19.2 V and 8.64 V to 13.6 V and 4.21 V. With 220 kΩ loads instead, the same steps give 19.1 V and 8.56 V, almost the no-load values.
Stiff dividers and bleeder current
The example shows the rule: loads comparable to the divider resistors pull the taps far down, loads 10 times larger still cost several percent (18.4 V and 7.92 V here), and loads 100 times larger barely move them. Put in terms of current, the current flowing down the divider, often called the bleeder current, should be large compared with the load currents. A divider that holds its voltages under load is called stiff. Stiffness has a price. Smaller divider resistors mean more bleeder current, and that current is wasted as heat even when no load draws anything. Designers therefore choose divider resistors small enough to keep the loading error acceptable but no smaller, and check every resistor's power rating.
Worked example: designing for known loads
From a 12 V source, design a three-resistor divider giving 9 V to a load that draws 5 mA and 3 V to a load that draws 2 mA, with 3 mA of bleeder current in the bottom resistor. Name the chain \(R_1\) from 12 V to tap a, \(R_2\) from a to tap b and \(R_3\) from b to ground. 1. \(R_3\) carries the bleeder current: \(R_3 = 3\,\text{V} / 3\,\text{mA} = 1.0\,\text{k}\Omega\). 2. KCL at b: \(R_2\) carries \(3 + 2 = 5\,\text{mA}\) and drops \(9 - 3 = 6\,\text{V}\), so \(R_2 = 1.2\,\text{k}\Omega\). 3. KCL at a: \(R_1\) carries \(5 + 5 = 10\,\text{mA}\) and drops 3 V, so \(R_1 = 300\,\Omega\). 4. Powers, \(I^2R\): 30 mW, 30 mW and 9 mW, so quarter-watt resistors suffice. All three values are standard E24 values.
The potentiometer as a divider
A potentiometer, one of the special resistors in "Resistor types, color codes, conductance, and special resistors", is a resistive track of total resistance \(R_T\) with a sliding wiper. With the ends across a source \(E\), the wiper splits the track into an upper part and a lower part, and the unloaded output from wiper to the bottom end follows the divider rule:
Turning the knob moves the output smoothly from 0 to \(E\). Used with only one end and the wiper connected, the same part becomes a variable resistor, or rheostat. Volume controls, trimmer adjustments and position sensors all rely on the divider connection.
Loading a potentiometer
A load \(R_L\) on the wiper is in parallel with the lower part of the track, so the output becomes
Now the output depends on the load as well as the knob. If \(R_L\) is much smaller than \(R_T\), most of the track's range does almost nothing, and the output stays near zero until the wiper is close to the top. For good control, choose the parts so that
and preferably \(R_L\) several times \(R_T\). Do not simply make \(R_T\) tiny, though: the track alone dissipates \(E^2 / R_T\), so 12 V across 100 Ω would need at least a 1.44 W part.
Worked example: a loaded potentiometer
A 10 kΩ potentiometer is connected across 12 V with its wiper set so that the lower part is 7.5 kΩ and the upper part 2.5 kΩ. Find the output for no load and for loads of 100 kΩ, 10 kΩ and 1 kΩ. 1. Unloaded: \(V_L = 12 \times 7.5 / 10 = 9.00\,\text{V}\). 2. 100 kΩ: \(R' = 6.98\,\text{k}\Omega\), so \(V_L = 12 \times \frac{6.98}{6.98 + 2.5} = 8.83\,\text{V}\). 3. 10 kΩ: \(R' = 4.29\,\text{k}\Omega\) and \(V_L = 7.58\,\text{V}\). 4. 1 kΩ: \(R' = 0.882\,\text{k}\Omega\) and \(V_L = 3.13\,\text{V}\). 5. Only the 100 kΩ load, ten times \(R_T\), stays within 2% of the knob setting; the 1 kΩ load breaks the rule \(R_L \ge R_T\) and loses about two-thirds of the voltage.
Common mistakes to avoid
First, using the unloaded divider rule after a load is connected; the load must be combined with the resistor below its tap. Second, assuming a load at one tap leaves the other taps alone: every load changes the current in the chain above it. Third, forgetting the bleeder current when designing, so the bottom resistor has no defined current. Fourth, connecting a low-resistance load to a high-resistance potentiometer and wondering why the knob seems dead over most of its travel. Fifth, shrinking divider or potentiometer resistances for stiffness without checking their power ratings.
Key takeaways
A load on a divider tap is in parallel with the resistance below it, so it lowers that tap and changes the others; solve the result as a series-parallel network. Loads 10 to 100 times the divider resistances, or a bleeder current well above the load currents, keep a divider stiff, at the cost of wasted power. Design a divider from the bottom up with KCL at each tap and check every power rating. A potentiometer is an adjustable divider: unloaded, \(V_L = E \cdot R_{\text{lower}} / R_T\); loaded, the lower part is in parallel with \(R_L\), and \(R_L \ge R_T\) keeps control.
Flashcards
Flashcard
A load in parallel with the divider resistance below its tap
Test your understanding
Question 1 of 5
Two 10 kΩ resistors in series across 20 V form a divider. A 10 kΩ load is connected across the lower resistor. What is the output voltage?
Question 2 of 5
A divider tap must give 6 V to a load drawing 4 mA, with 2 mA of bleeder current in the bottom resistor from the tap to ground. What is the bottom resistor?
Question 3 of 5
A 50 kΩ potentiometer has its wiper at the middle and drives a 1 kΩ load. What happens to the output compared with the unloaded setting?
Question 4 of 5
Why should divider resistors not simply be made as small as possible to keep the outputs stiff?
Question 5 of 5
For good control of a load from a potentiometer, which condition should hold?
