Electrical Engineering › Section D · Parallel and series-parallel circuits › Topic D.6
Series-parallel and ladder networks
Most practical resistive networks mix series and parallel connections. With a clear way to spot each kind of group, reduce the network and work back out again, you can find any voltage or current in them using only Ohm's law, KVL, KCL and the divider rules.
Beyond pure series and pure parallel
Few useful circuits are purely series or purely parallel. A sensor divider feeding a meter or a supply rail with several loads combines the two. Such a series-parallel network can still be solved with the tools you already have: Ohm's law, KVL, KCL and the divider rules. The new skill is organisation: recognising each series group and each parallel group, collapsing them in a sensible order and then working back out to the quantity you want. This topic builds that skill and applies it to the ladder network, a repeating chain of series and shunt resistors.
Spotting series and parallel groups
Two elements are in series when they carry the same current: they share a node that nothing else connects to. Two elements are in parallel when they connect between the same two nodes, so they share a voltage. These tests apply to whole blocks as well as single resistors. A branch made of \(R_3\) and \(R_4\) in series is one block, and that block can be in parallel with \(R_2\). A compact notation helps: \(R_{3,4} = R_3 + R_4\) for series and \(R_2 \parallel R_{3,4}\) for parallel. Elements that merely look adjacent on a drawing are not necessarily in series; always check the nodes.
Reduce and return
For a network with a single source, a reliable plan has two halves. Reduce: combine series and parallel groups step by step, starting from the end farthest from the source, until one equivalent resistance \(R_T\) remains. Then find the source current \(I_s = E / R_T\). Return: work back through the drawings you made, in reverse order. Series elements share a current, so multiply by each resistance to get its voltage. Parallel elements share a voltage, so divide it by each branch resistance, or use the current divider rule. Keep each reduction sketch, because the same sketches are your map on the way back.
Worked example: reduce and return
A 24 V source feeds \(R_1 = 1.5\,\text{k}\Omega\) from its + terminal to node a. From a to ground run two branches: \(R_2 = 4.7\,\text{k}\Omega\), and \(R_3 = 1.0\,\text{k}\Omega\) in series with \(R_4 = 3.3\,\text{k}\Omega\). 1. \(R_{3,4} = 4.3\,\text{k}\Omega\). 2. \(R_2 \parallel R_{3,4} = \frac{4.7 \times 4.3}{9.0} = 2.246\,\text{k}\Omega\). 3. \(R_T = 1.5 + 2.246 = 3.746\,\text{k}\Omega\), so \(I_s = 24 / 3.746\,\text{k} = 6.41\,\text{mA}\). 4. \(V_a = 6.41\,\text{mA} \times 2.246\,\text{k}\Omega = 14.4\,\text{V}\). 5. \(I_2 = 14.4 / 4.7\,\text{k} = 3.06\,\text{mA}\) and \(I_{3,4} = 14.4 / 4.3\,\text{k} = 3.35\,\text{mA}\). 6. \(V_4 = 3.35\,\text{mA} \times 3.3\,\text{k}\Omega = 11.0\,\text{V}\). Check by KCL: \(3.06 + 3.35 = 6.41\,\text{mA}\).
Ask only what the question asks
A full solution is not always needed. If a branch connects directly across the source, its current is simply the source voltage divided by that branch's resistance, whatever else the network contains. If you need one voltage inside a series chain, reduce only what lies around it and apply the voltage divider rule. Before writing equations, sketch the plan: which blocks are in series or parallel, and which quantities survive each reduction. Awkward drawings deserve redrawing first. Label every node, join all points marked with a ground symbol, since they are one node, and replace terminal labels such as "+12 V" with actual sources. Many confusing networks turn out to be familiar shapes.
Worked example: voltage between two points
An 18 V source drives two branches in parallel. In branch 1, \(R_1 = 2.2\,\text{k}\Omega\) runs from the + terminal to node a and \(R_2 = 3.3\,\text{k}\Omega\) from a to ground. In branch 2, \(R_3 = 4.7\,\text{k}\Omega\) runs from the + terminal to node b and \(R_4 = 1.0\,\text{k}\Omega\) from b to ground. Find \(V_{ab}\) and the source current. 1. Each branch has the full 18 V across it, so each is a separate voltage divider. 2. \(V_a = 18 \times \frac{3.3}{5.5} = 10.8\,\text{V}\). 3. \(V_b = 18 \times \frac{1.0}{5.7} = 3.16\,\text{V}\). 4. \(V_{ab} = V_a - V_b = 7.64\,\text{V}\), with a positive. 5. Branch currents are \(18 / 5.5\,\text{k} = 3.27\,\text{mA}\) and \(18 / 5.7\,\text{k} = 3.16\,\text{mA}\), so \(I_s = 6.43\,\text{mA}\). A voltage need not be across a single element.
Ladder networks
A ladder network repeats one pattern: a series resistor, then a shunt resistor to ground, then another series resistor, and so on, like the rails and rungs of a ladder. Ladders appear in attenuators and in the resistor networks inside some digital-to-analogue converters. The first method of solving one is reduce and return. Start at the far end, where the last series and shunt resistors form a simple series pair. Combine it, put the result in parallel with the next shunt resistor, add the next series resistor, and keep going until you reach the source. Then find the source current and use the current divider rule at each rung on the way back.
Worked example: a ladder, method 1
A 36 V source feeds a three-section ladder: series \(R_1 = 1.5\,\text{k}\Omega\) from + to node a; shunt \(R_2 = 1.8\,\text{k}\Omega\) from a to ground; series \(R_3 = 7.5\,\text{k}\Omega\) from a to b; shunt \(R_4 = 3.0\,\text{k}\Omega\) from b to ground; series \(R_5 = 1.0\,\text{k}\Omega\) from b to c; shunt \(R_6 = 2.0\,\text{k}\Omega\) from c to ground. Find \(I_6\). 1. \(R_5 + R_6 = 3.0\,\text{k}\Omega\), in parallel with \(R_4\): 1.5 kΩ. 2. Add \(R_3\): 9.0 kΩ, in parallel with \(R_2\): 1.5 kΩ. 3. \(R_T = 3.0\,\text{k}\Omega\) and \(I_s = 12\,\text{mA}\). 4. At node a: \(I_3 = 12 \times \frac{1.8}{1.8 + 9.0} = 2.0\,\text{mA}\). 5. At node b, two equal 3.0 kΩ paths split it: \(I_6 = 1.0\,\text{mA}\), so \(V_6 = 2.0\,\text{V}\).
Worked example: the same ladder, method 2
The second method names the current in the last rung and works towards the source. Let \(I_6 = I\). 1. \(V_4 = (R_5 + R_6)I = 3.0\,\text{k}\Omega \cdot I\), so \(I_4 = V_4 / R_4 = I\) and, by KCL, \(I_3 = 2I\). 2. \(V_3 = 7.5\,\text{k}\Omega \cdot 2I = 15\,\text{k}\Omega \cdot I\), so \(V_2 = V_3 + V_4 = 18\,\text{k}\Omega \cdot I\). 3. \(I_2 = V_2 / 1.8\,\text{k}\Omega = 10I\), so \(I_s = 12I\). 4. \(V_1 = 1.5\,\text{k}\Omega \cdot 12I = 18\,\text{k}\Omega \cdot I\). 5. KVL: \(E = V_1 + V_2 = 36\,\text{k}\Omega \cdot I\), so \(I = 36 / 36\,\text{k} = 1.0\,\text{mA}\), matching method 1. Method 2 shines when only the far-end quantity is wanted.
Common mistakes to avoid
First, calling two resistors in series when a third branch leaves the node between them. Second, applying the voltage divider rule across resistors that do not carry the same current. Third, reducing from the source end of a ladder instead of the far end, where the first simple pair lies. Fourth, using the source voltage across a resistor that is buried inside the network; only branches connected directly across the source see the full voltage. Fifth, forgetting that all ground symbols are one node. A KCL check at each node and a KVL check around one loop catch most of these slips.
Key takeaways
Series elements share a current and a private node; parallel elements share the same two nodes and a voltage, and these tests apply to whole blocks. Reduce and return: combine groups from the far end to get \(R_T\) and \(I_s = E / R_T\), then work back with Ohm's law and the divider rules. Find only the unknowns asked for, and redraw awkward networks first. A voltage between two points can be found from their voltages to ground. Ladders are solved either by reducing from the far end or by naming the last current and working towards the source.
Flashcards
Flashcard
Same current; the shared node connects nothing else
Test your understanding
Question 1 of 5
A 12 V source feeds a 2.0 kΩ resistor in series with a parallel pair of 6.0 kΩ and 3.0 kΩ to ground. What is the source current?
Question 2 of 5
In that same circuit (12 V, 2.0 kΩ in series with 6.0 kΩ ∥ 3.0 kΩ), what current flows in the 3.0 kΩ resistor?
Question 3 of 5
A 20 V source drives two branches in parallel. Branch 1 is 1.0 kΩ from + to node a, then 4.0 kΩ to ground. Branch 2 is 3.0 kΩ from + to node b, then 2.0 kΩ to ground. What is Vab?
Question 4 of 5
When reducing a ladder network to find its total resistance, where should you start?
Question 5 of 5
In a two-section ladder, method 2 gives E = 18 kΩ × I4, where I4 is the current in the last rung. If E = 9 V, what is I4?
