Electrical Engineering › Section B · Resistance, Ohm's law, power, and energy › Topic B.4

Ohm's law

Push harder and more flows; add more opposition and less flows. Ohm's law puts that common-sense idea into one exact equation linking voltage, current and resistance, and it is the first tool of almost every circuit calculation in this course.

Cause, effect and opposition

Every circuit has a cause, an effect and an opposition. The cause is the applied voltage, which supplies energy to each unit of charge. The effect is the current that results. The opposition is the resistance of the path. Double the voltage across a fixed resistor and twice as much current flows; double the resistance with the voltage fixed and the current halves. Georg Ohm published this relationship in 1827, after careful experiments with wires of different lengths. For the resistors and wires of ordinary circuit work, at a steady temperature, it holds with excellent accuracy.

The law and its three forms

For a resistor, the voltage across it equals the current through it times its resistance:

V = IR

It rearranges to \(I = \frac{V}{R}\), to find a current, and \(R = \frac{V}{I}\), to find a resistance from a measurement. With volts, amperes and ohms, no conversion factors are needed. Prefixes pair neatly: volts divided by kilohms give milliamperes, and milliamperes times kilohms give volts. When the voltage comes straight from a source it is often written \(E\), so the current in a single resistor across a battery is \(I = \frac{E}{R}\). The ohm itself is defined by the law: 1 Ω passes 1 A when 1 V is across it.

Polarity and direction

Ohm's law gives sizes; the circuit sets directions. With conventional current and the passive sign convention, current enters a resistor at the terminal marked + and leaves at the terminal marked −. In other words, the end where current enters is the higher-potential end, and the voltage across the resistor is a drop in the direction of the current. A source is the reverse: inside it, charge is pushed from − to +, so current leaves its + terminal. Take a 12 V battery with one resistor across it: current leaves the battery's + terminal, enters the resistor's top terminal, and the resistor shows +12 V at that end.

Worked example: finding a current

A 2.2 kΩ resistor is connected directly across a 12 V dc supply, the supply's + terminal to resistor terminal \(a\) and its − terminal to terminal \(b\), which is grounded. Find the current and its direction. 1. Ohm's law: \(I = \frac{V}{R} = \frac{12\,\text{V}}{2.2\,\text{k}\Omega}\). 2. Volts over kilohms give milliamperes: \(I = 5.45\) mA. 3. Direction: conventional current leaves the supply's + terminal, so it enters the resistor at \(a\) and leaves at \(b\). 4. Polarity: \(a\) is the + end, and \(V_{ab} = +12\) V. 5. Check: \(5.45\,\text{mA} \times 2.2\,\text{k}\Omega = 12.0\) V, recovering the supply voltage.

Worked example: voltage and resistance

1. A 33 Ω resistor in a sensor circuit carries 150 mA. The voltage across it is \(V = IR = 0.150 \times 33 = 4.95\) V. 2. In a different circuit, a meter shows 9.0 V across an unknown resistor and an ammeter in series with it reads 0.60 mA. The resistance is \(R = \frac{V}{I} = \frac{9.0}{0.60 \times 10^{-3}} = 15{,}000\) Ω, or 15 kΩ. 3. Check part 2 against the colour-coded value: 15 kΩ is in the E12 series, so a brown, green, orange band pattern would confirm it. 4. Check part 1 by size: a third of an ampere would need 11 V across 33 Ω, so 150 mA giving about 5 V is consistent.

Plotting Ohm's law

Graph current \(I\) on the vertical axis against voltage \(V\) on the horizontal axis for a resistor and you get a straight line through the origin. The line's slope is \(\frac{I}{V} = \frac{1}{R}\), the conductance \(G\). A steep line means a small resistance, and a shallow line a large one; a horizontal line along the axis is an open circuit and a vertical line a short circuit. The resistance is found from any two points as

R = \frac{\Delta V}{\Delta I}

Because the line passes through the origin, a single point gives it too. Reversing the voltage reverses the current, so the line continues symmetrically into negative values.

Worked example: reading a graph

Measurements on a component give 5.0 mA at 3.4 V and 15.0 mA at 10.2 V. 1. Changes: \(\Delta V = 10.2 - 3.4 = 6.8\) V and \(\Delta I = 15.0 - 5.0 = 10.0\) mA. 2. Resistance: \(R = \frac{\Delta V}{\Delta I} = \frac{6.8\,\text{V}}{10.0\,\text{mA}} = 680\) Ω. 3. Test linearity: each point alone gives \(\frac{3.4}{5.0\,\text{mA}} = 680\) Ω and \(\frac{10.2}{15.0\,\text{mA}} = 680\) Ω, the same, so the line passes through the origin and the part is ohmic. 4. Identify: 680 Ω is an E12 value, so this is almost certainly an ordinary resistor.

When Ohm's law is not enough

Many components are non-ohmic: their voltage and current are not proportional. A filament lamp's current rises less than proportionally as the voltage rises, because the filament heats and its resistance grows; a lamp drawing 0.50 A at 6 V (12 Ω) might draw only 0.80 A at 12 V (15 Ω). A silicon diode passes almost no current until its forward voltage reaches roughly 0.6 to 0.7 V, then conducts steeply, and in reverse passes almost nothing. For such parts \(\frac{V}{I}\) at a point still defines a resistance at that operating point, and \(\frac{\Delta V}{\Delta I}\) over a small step gives the dynamic resistance, but neither is a constant. Their curves are covered in "Diode basics, meter checks, ratings, and rectifier circuits".

Opens, shorts and current sensing

Two limiting cases follow from \(I = \frac{V}{R}\). An open circuit has unlimited resistance, so no current flows however large the voltage across the gap. A short circuit has almost no resistance, so a source placed across it would try to drive an enormous current, which is why shorts melt wires and blow fuses. A practical use of Ohm's law is current sensing: a small, precise resistor called a shunt is placed in series, and the voltage across it measures the current. A 0.100 Ω shunt showing 0.250 V carries \(\frac{0.250}{0.100} = 2.50\) A. "Sources in parallel, open circuits, and short circuits" returns to opens and shorts in networks.

Common mistakes to avoid

First, mixing prefixes, such as dividing volts by kilohms and calling the answer amperes. Second, using the source voltage when the question asks about one resistor that does not have the full voltage across it. Third, rearranging wrongly, for instance \(R = VI\). Fourth, reading the slope of an \(I\)-\(V\) graph as \(R\) rather than \(\frac{1}{R}\). Fifth, applying a single fixed resistance to a lamp or diode. Sixth, drawing the voltage drop across a resistor with the + sign on the end where current leaves.

Key takeaways

Ohm's law, published in 1827: V = IR, so I = V/R and R = V/I, with volts, amperes and ohms; volts over kilohms give milliamperes. Under the passive sign convention, current enters a resistor at its + end, so the voltage drops in the direction of current. An I-V graph of a resistor is a straight line through the origin with slope 1/R; R = ΔV/ΔI from any two points. Lamps and diodes are non-ohmic. An open circuit carries no current, and a short circuit has almost no voltage across it. A shunt measures current through its voltage.

Flashcards

Flashcard

V = IR

Ohm's law: voltage equals current times resistance

Georg Ohm, 1827.

Test your understanding

Question 1 of 5

A 9.0 V battery is connected across a 1.5 kΩ resistor. What current flows?

Question 2 of 5

A 470 Ω resistor carries 25 mA. What is the voltage across it?

Question 3 of 5

The I-V graph of a resistor, with current on the vertical axis, is a straight line through the origin and the point (5.0 V, 2.0 mA). What is the resistance?

Question 4 of 5

A lamp draws 0.20 A at 3.0 V and 0.30 A at 6.0 V. What do these readings show?

Question 5 of 5

A 0.050 Ω shunt carries a motor's current, and a meter across it reads 0.20 V. What is the current?

← Previous topicNext topic →