Electrical Engineering › Section B · Resistance, Ohm's law, power, and energy › Topic B.3
Resistor types, color codes, conductance, and special resistors
Resistors are the most common components on any circuit board. Knowing how they are built, how their values are marked and which standard values exist lets you read a board at a glance and choose parts that can actually be bought.
Fixed resistors
A fixed resistor has one value, set when it is made. Carbon-composition resistors, a moulded mix of carbon and binder, are now rare but survive where short pulses must be absorbed. Carbon-film and metal-film resistors deposit a thin resistive layer on a ceramic rod and cut a spiral into it to set the value; metal film is more precise and drifts less with temperature. Wirewound resistors wind resistance wire such as nichrome on a core and handle several watts or more. Most modern boards use surface-mount chip resistors, a thick or thin film printed on a tiny ceramic block. A part's physical size sets how much heat it can safely shed, its power rating.
Variable resistors
A potentiometer has a resistive track with a terminal at each end and a sliding contact, the wiper, between them. Turning the shaft moves the wiper, so the resistance from the wiper to either end changes while the end-to-end value stays fixed. Wired with all three terminals it supplies an adjustable fraction of a voltage, as in a volume control; "Loaded voltage dividers and potentiometers" analyses that use. Wired with only the wiper and one end, it acts as a rheostat, a two-terminal adjustable resistance. Small trimmer potentiometers, set once with a screwdriver, calibrate circuits during manufacture. Tracks can be linear or logarithmic in taper.
The colour code
Through-hole resistors are too small to print on, so their values are marked with coloured bands, read from the end with the band nearest to it. Each colour stands for a digit:
On a four-band resistor, the first two bands are digits, the third is the power-of-ten multiplier and the fourth is the tolerance: gold \(\pm 5\%\), silver \(\pm 10\%\), and no band \(\pm 20\%\). As a multiplier, gold means \(10^{-1}\) and silver \(10^{-2}\), for values under 10 Ω. Five-band precision resistors use three digits, a multiplier, then the tolerance: brown \(\pm 1\%\), red \(\pm 2\%\).
Worked example: reading four bands
A resistor's bands read yellow, violet, red, gold. 1. Digits: yellow = 4 and violet = 7, giving 47. 2. Multiplier: red = 2, so multiply by \(10^2\): \(47 \times 100 = 4700\) Ω, or 4.7 kΩ. 3. Tolerance: gold = \(\pm 5\%\), and 5% of 4700 Ω is 235 Ω. 4. Range: the true value may lie anywhere from \(4700 - 235 = 4465\) Ω to \(4700 + 235 = 4935\) Ω. 5. Check: 4.7 kΩ is a standard value, as it should be; if a reading gives a value that is not in the standard series, you are probably reading the bands from the wrong end.
Standard values
Manufacturers do not make every value. They make preferred values from the E series, in which each decade is split into steps of nearly equal ratio. The E12 series, for \(\pm 10\%\) parts, is 10, 12, 15, 18, 22, 27, 33, 39, 47, 56, 68, 82, times any power of ten; each step is about 1.2 times the last. With \(\pm 10\%\) tolerance, neighbouring values almost meet, so almost any resistance lies within tolerance of some E12 value. The E24 series, for \(\pm 5\%\) parts, adds values in between, such as 11, 13, 16, 20, 51 and 91; E96 serves 1% parts. Designs are finished by rounding each calculated value to a standard one.
Worked example: five bands and surface-mount codes
1. Five bands read orange, orange, black, brown, brown. The digits are 3, 3, 0, giving 330; the multiplier brown is \(10^1\); so the value is 3300 Ω = 3.30 kΩ. The final brown band means \(\pm 1\%\), a range of 3267 Ω to 3333 Ω. 2. A chip resistor is printed 472. In the three-digit code the first two digits are significant and the third is the number of zeros: 47 followed by two zeros, 4700 Ω. 3. A precision chip printed 1002 uses four digits the same way: 100 followed by two zeros, 10.0 kΩ. 4. A chip printed 4R7: the R marks the decimal point, so 4.7 Ω.
Conductance
Sometimes it is more natural to describe how easily a component passes current than how strongly it opposes it. Conductance, symbol \(G\), is the reciprocal of resistance:
measured in siemens (S); older texts call the unit the mho. A 2.2 kΩ resistor has \(G = \frac{1}{2200} = 455\) µS. A short circuit has zero resistance and unlimited conductance; an open circuit has unlimited resistance and zero conductance. Conductance makes later work on parallel circuits neater, as "Parallel elements, total conductance, and resistance" will show. Doubling a resistance halves its conductance.
Ohmmeters
An ohmmeter, usually the Ω setting of a DMM, measures resistance by passing a small known current from its own battery through the part and measuring the result. Two rules follow. Measure only with the circuit unpowered, because any voltage from the circuit spoils the reading and can damage the meter. And for an accurate value, lift at least one lead of the component out of the circuit, since otherwise the meter also sees every other path between the two points. Touch the probes together first: the small reading is the lead resistance, to subtract from low readings. Ohmmeters also check continuity, confirming that a wire or fuse is unbroken.
Special resistors
Some resistors are designed to change. A thermistor's resistance depends strongly on temperature: an NTC thermistor, made from a semiconducting metal oxide, falls in resistance as it warms, with 10 kΩ at 25 °C a common rating, and is used in thermometers and battery packs. PTC thermistors rise sharply above a set temperature and serve as resettable fuses. A photoconductive cell, or light-dependent resistor, falls from megohms in darkness to a few hundred ohms in bright light; cadmium-sulphide types are now restricted in many countries. A varistor, usually a metal-oxide varistor (MOV), has a very high resistance at normal voltages but conducts heavily above its rated voltage, clamping surges in power strips.
Common mistakes to avoid
First, reading the colour bands from the wrong end; the tolerance band is usually set slightly apart. Second, treating the third band of a four-band resistor as a digit rather than a multiplier. Third, reading a chip code such as 103 as 103 Ω instead of 10 kΩ. Fourth, measuring resistance in a powered circuit, or with the part still connected to other paths. Fifth, expecting a calculated value such as 5.07 kΩ to exist; round to a standard value. Sixth, confusing conductance in siemens with resistance in ohms.
Key takeaways
Fixed resistors are carbon-composition, carbon-film, metal-film, wirewound or surface-mount chips; potentiometers and rheostats are adjustable. Four bands give two digits, a multiplier and a tolerance (gold ±5%, silver ±10%); five bands give three digits. Chip codes give significant digits then the number of zeros, and R marks a decimal point. Values come from the E series, such as E12 for ±10% parts. Conductance G = 1/R in siemens. Measure resistance with the circuit unpowered and the part isolated. Thermistors, photoconductive cells and varistors change resistance with temperature, light and voltage.
Flashcards
Flashcard
A precise fixed resistor with a thin metal layer on a ceramic rod
Test your understanding
Question 1 of 5
A four-band resistor reads red, red, orange, gold. What is its marked value and tolerance?
Question 2 of 5
A 680 Ω resistor has a tolerance of ±10%. Within what range may its true value lie?
Question 3 of 5
A surface-mount resistor is printed 153. What is its value?
Question 4 of 5
What is the conductance of a 500 Ω resistor?
Question 5 of 5
Which special resistor would protect a power strip from a voltage surge?
