Electrical Engineering › Section L · Power (ac) and resonance › Topic L.5

Series resonance and the quality factor

At one particular frequency an inductor and a capacitor in series cancel each other completely, the circuit looks like a plain resistor, and the current peaks. That is resonance, the principle behind every tuned circuit from a radio's front end to a filter that picks out a single tone.

What resonance means

Push a child on a swing at just the right rhythm and small pushes build a large motion; that rhythm is the swing's natural frequency. An electrical circuit with both inductance and capacitance has a natural frequency too. At that frequency the energy released by one reactive element is exactly the energy absorbed by the other, so it swings back and forth between the inductor's magnetic field and the capacitor's electric field, and the source only has to make up what resistance turns into heat. The circuit's response, current or voltage, peaks near this frequency and falls away on either side. A radio receiver is tuned by moving this peak onto the station you want.

The series resonant circuit

A series resonant circuit is an ac voltage source \(E\) in series with an inductor \(L\), a capacitor \(C\) and resistance. The resistance always exists: the source's internal resistance \(R_s\), the winding resistance of the coil \(R_l\), and any resistor \(R_d\) added by the designer to shape the response. Because they are all in series, they combine into one total,

R = R_s + R_l + R_d

The total impedance at any frequency is, in rectangular form,

Z_T = R + j(X_L - X_C)

As frequency rises \(X_L = \omega L\) grows and \(X_C = 1/(\omega C)\) shrinks, so at exactly one frequency they are equal.

The resonant frequency

Series resonance is defined by \(X_L = X_C\), which removes the imaginary part of \(Z_T\). Setting \(\omega L = 1/(\omega C)\) and solving gives

\omega_s = \frac{1}{\sqrt{LC}},\qquad f_s = \frac{1}{2\pi\sqrt{LC}}

with \(L\) in henries, \(C\) in farads and \(f_s\) in hertz; the subscript s marks series resonance. Notice that \(R\) does not appear: resistance does not move the resonant frequency of a series circuit, only the sharpness of the peak. Quadrupling \(L\) or \(C\) halves \(f_s\), because of the square root.

Conditions at resonance

At \(f_s\) the impedance is \(Z_T = R\), its minimum value, so the current \(I = E/R\) is the maximum the source can drive, and it is in phase with \(E\). The voltage across the resistor equals the whole source voltage. The inductor and capacitor carry the same current, so their voltages have equal size, \(V_L = IX_L = V_C = IX_C\), but are \(180^\circ\) apart (\(V_L\) at \(+90^\circ\), \(V_C\) at \(-90^\circ\) to \(I\)) and cancel. In the power triangle \(Q_L\) and \(Q_C\) cancel, so \(S = P = I^2R\) and the power factor is 1. The total stored energy, \(\tfrac12Li^2 + \tfrac12Cv_C^2\), stays constant through the cycle while it moves between the two elements.

Worked example: finding the resonant conditions

A 2.0 V rms source drives a 4.7 mH inductor and a 22 nF capacitor in series, with a total resistance of 22 Ω. 1. \(f_s = 1/(2\pi\sqrt{4.7\times10^{-3} \times 22\times10^{-9}}) = 15.7\) kHz. 2. At \(f_s\), \(X_L = 2\pi f_sL = 462\,\Omega\), and \(X_C = 1/(2\pi f_sC) = 462\,\Omega\), equal as required. 3. \(Z_T = 22\,\Omega\), so \(I = 2.0/22 = 90.9\) mA, in phase with \(E\). 4. \(V_R = 2.0\) V, and \(V_L = V_C = 0.0909 \times 462 = 42.0\) V. 5. \(P = I^2R = 0.182\) W and \(Q_L = I^2X_L = 3.82\) VAR, cancelled by \(Q_C\). The capacitor sees 21 times the source voltage.

The quality factor

The quality factor \(Q_s\) measures how much energy is in storage compared with how much is lost. It is defined at resonance as

Q_s = \frac{\text{reactive power of } L \text{ or } C}{\text{average power}} = \frac{I^2X_L}{I^2R} = \frac{X_L}{R}

Substituting \(\omega_s = 1/\sqrt{LC}\) gives a form in the parts alone:

Q_s = \frac{1}{R}\sqrt{\frac{L}{C}}

Equivalently, \(Q_s\) is \(2\pi\) times the peak stored energy divided by the energy dissipated per cycle. In the worked example \(Q_s = 462/22 = 21.0\). Do not confuse this \(Q\) with reactive power \(Q\); the subscripts s, l and p mark quality factors.

Voltage magnification

By the voltage divider rule, at resonance \(V_L = (X_L/R)E\) and \(V_C = (X_C/R)E\), so

V_{L} = V_{C} = Q_sE

With \(Q_s\) above 1, as in nearly every tuned circuit, the reactive voltages exceed the source voltage, sometimes enormously. A 10 V source with \(Q_s = 50\) puts 500 V across the capacitor. That is useful, since it makes a weak signal at the resonant frequency stand out, but it is also a hazard: capacitors and coil insulation in resonant circuits must be rated for \(Q_s\) times the drive voltage, not the drive voltage itself.

The quality factor of a coil

When the only resistance is the coil's own, \(Q_s\) becomes the coil's quality factor, \(Q_l = X_L/R_l\), the figure inductor makers quote. Since \(X_L = 2\pi fL\), you might expect \(Q_l\) to rise in proportion to frequency, and at low and middle frequencies it roughly does. At higher frequencies the coil's effective resistance rises, mainly through skin effect (see "Wattmeters and effective resistance"), and the capacitance between turns starts to matter, so \(Q_l\) levels off and then falls. A coil's \(Q_l\) must therefore be stated at a frequency, and data sheets often plot it against frequency. Typical small inductors reach a few tens to around a hundred.

Worked example: a radio tuning circuit

A 220 µH coil with effective resistance 15 Ω is tuned to 1.00 MHz by a variable capacitor, driven by an antenna signal of 10 mV with a source resistance of 50 Ω. 1. \(C = 1/(\omega^2L) = 1/((2\pi \times 10^6)^2 \times 220\times10^{-6}) = 115\) pF. 2. \(X_L = 2\pi(10^6)(220\times10^{-6}) = 1382\,\Omega\), so \(Q_l = 1382/15 = 92.2\). 3. Total \(R = 50 + 15 = 65\,\Omega\), so \(Q_s = 1382/65 = 21.3\). 4. \(V_C = Q_sE = 21.3 \times 10 = 213\) mV. 5. Note: the source resistance cut \(Q_s\) to under a quarter of \(Q_l\).

Common mistakes to avoid

First, mixing \(\omega\) and \(f\): \(1/\sqrt{LC}\) is in radians per second, and you must divide by \(2\pi\) for hertz. Second, slipping a prefix: nF is \(10^{-9}\) F and µH is \(10^{-6}\) H, and an error under the square root shifts the answer by a factor of about 31.6 for each factor of 1000. Third, using only the coil's resistance when the source or a design resistor is also in series. Fourth, assuming no voltage can exceed the source voltage: at resonance \(V_L = V_C = Q_sE\). Fifth, thinking resistance changes \(f_s\) in a series circuit: it changes only \(Q_s\).

Key takeaways

Series resonance occurs when \(X_L = X_C\), at \(f_s = 1/(2\pi\sqrt{LC})\), independent of \(R\). There the impedance is a minimum, \(Z_T = R\), the current \(E/R\) is a maximum and in phase with \(E\), the power factor is 1 and \(S = P\). The inductor and capacitor voltages are equal, opposite and each \(Q_sE\). The quality factor is \(Q_s = X_L/R = (1/R)\sqrt{L/C}\), the ratio of reactive to real power; \(R\) includes source, coil and design resistance. A coil's own \(Q_l = X_L/R_l\) depends on frequency.

Flashcards

Flashcard

Resonance

The frequency at which a circuit's inductive and capacitive reactances balance

Energy swaps between L and C.

Test your understanding

Question 1 of 5

A series circuit has L = 10 mH and C = 100 nF. What is its resonant frequency?

Question 2 of 5

A series resonant circuit has R = 8 Ω and X_L = X_C = 400 Ω at resonance, driven by 5 V. What is the voltage across the capacitor?

Question 3 of 5

In a series R-L-C circuit, the resistance is doubled while L and C stay the same. What happens?

Question 4 of 5

Which statement describes a series R-L-C circuit exactly at its resonant frequency?

Question 5 of 5

A 1.0 mH coil has a winding resistance of 6.0 Ω. What is its quality factor at 150 kHz?

← Previous topicNext topic →