Electrical Engineering › Section Z · AC motors › Topic Z.3
Stepper motors and brushless DC motors
Stepper motors and brushless DC motors both run from a dc supply, yet both are really ac machines: electronics switch their windings in sequence to make a moving field. Steppers turn that into precise steps, brushless motors into smooth, efficient rotation.
A motor that counts
A stepper motor moves through a fixed angle, the step angle, each time its driver changes the pattern of current in its windings. Send 200 pulses to a 1.8° stepper and the shaft turns exactly one revolution; stop the pulses and, while still energised, it holds its position with its holding torque. Because position is the count of steps, a controller can place a printer head with no position sensor: an open-loop system. A servo motor needs a sensor and an error amplifier in a feedback loop; it costs more but suits heavy loads and high acceleration.
Step angle and the three types
Step angles range from about 90° down to a fraction of a degree. The number of steps per revolution is \(360^\circ/\theta_{step}\): a 7.5° motor has 48, a 1.8° motor 200. Since the motor follows the pulses, its speed in rpm is the step rate times 60, divided by the steps per revolution. There are three types. A variable reluctance (VR) stepper has a toothed soft-iron rotor. A permanent magnet (PM) stepper has a magnetised rotor. A hybrid stepper has a magnetised rotor with fine iron teeth. Turn an unpowered shaft by hand: if you feel a cogging detent torque, the rotor contains a magnet; a VR stepper turns freely.
The variable reluctance stepper
A VR stepper works like the switched reluctance motor of "Synchronous motors, synchronous condensers, and reluctance motors": energising one stator phase pulls the nearest rotor teeth into line with its poles, the position of least reluctance. The rotor has fewer teeth than the stator has poles, so when the next phase is energised a different rotor tooth is pulled into line, and the rotor moves only by the difference of the two pitches:
where \(N_r\) counts rotor teeth and \(N_s\) stator poles. Reversing the phase sequence reverses the rotation.
Worked example: a four-phase VR stepper
A VR stepper has 8 stator poles, wired as 4 phases of 2 opposite poles each, and 6 rotor teeth. 1. Rotor pitch: \(360^\circ/6 = 60^\circ\). 2. Stator pitch: \(360^\circ/8 = 45^\circ\). 3. Step angle: \(60^\circ - 45^\circ = 15^\circ\). 4. Steps per revolution: \(360/15 = 24\). 5. Check with the other common form, \(360^\circ\) divided by phases times rotor teeth: \(360/(4 \times 6) = 15^\circ\). 6. Note the direction: the stator field jumps 45° one way at each step, while the rotor moves 15° the opposite way. 7. At 120 steps per second the shaft turns \(120 \times 60/24 = 300\,\text{rpm}\).
Driving a PM stepper
A typical PM stepper has two phase windings and a multi-pole magnet rotor. The order of the current patterns sets the mode. In wave drive one winding is energised at a time: simple, but the least torque. In full-step drive both windings are energised at once, so the rotor settles midway between poles; the step angle is unchanged and the torque is higher. Half-step drive alternates one winding and two, doubling the number of steps. Microstepping goes further: the driver varies the two winding currents sinusoidally, interpolating many positions between full steps for smoother motion. Cheap PM steppers often use can-stack construction: each coil sits in a steel cup whose interleaved fingers form many poles.
Hybrid steppers and winding connections
A hybrid stepper's rotor is a magnet, magnetised along the shaft, between two toothed iron cups offset by half a tooth, so one cup presents north teeth and the other south. The stator poles carry matching teeth. With the common 50 rotor teeth and two phases, the motor makes \(2 \times 2 \times 50 = 200\) full steps, 1.8° each. Windings may be bipolar, needing a driver that reverses current, usually an H-bridge, with four leads; or centre-tapped, with five or six leads, for a simpler unipolar driver that feeds either half of each coil. Bipolar drive gets more torque from the same copper.
Torque, speed and lost steps
A stepper's torque is greatest at standstill, the holding torque, and falls as the step rate rises, because the windings' inductance stops current building fully within each shorter step. The pull-in torque is the most load it can start and stop against without losing a step; the pull-out torque is the most it can sustain once running. A stopped motor cannot jump to full speed, so the controller ramps the step rate up and down. Some step rates excite mechanical resonance. Because the system is open loop, a missed step goes unnoticed, so printers and machine tools first drive each axis to a home switch and count from there.
Worked example: a 3D-printer axis
A 1.8° stepper with 1/16 microstepping drives a lead screw whose nut advances 8.0 mm per revolution. 1. Microsteps per revolution: \(200 \times 16 = 3200\). 2. Microsteps per millimetre: \(3200/8.0 = 400\), a resolution of \(1/400\,\text{mm} = 2.5\,\mu\text{m}\) per microstep. 3. A 50 mm move needs \(50 \times 400 = 20{,}000\) microsteps. 4. To travel at 40 mm/s the driver must issue \(40 \times 400 = 16{,}000\) microsteps per second. 5. Shaft speed: \(40/8.0 = 5.0\) revolutions per second, or 300 rpm. Microsteps improve smoothness more than true accuracy.
The brushless DC motor
A brushless DC (BLDC) motor turns the brushed dc motor inside out: permanent magnets on the rotor, windings on the stator, usually three phases. A brushed motor's commutator switches coil current mechanically; a BLDC motor's driver does it with transistors, timed by rotor position from three Hall-effect sensors, typically 120° electrical apart. In six-step commutation two phases conduct at a time, and the pattern changes six times per electrical cycle. Its back EMF is roughly trapezoidal; a motor wound for a sinusoidal back EMF and driven with sine-wave currents is called a permanent-magnet synchronous motor, the efficient machine in many electric vehicles. Rotors may be inside the stator, outside it (outrunners, common in fans and drones) or flat discs (pancake).
Worked example: commutation in a drone motor
An outrunner BLDC motor has 14 magnet poles, 7 pole pairs, and spins at 6,000 rpm. 1. Mechanical speed: \(6000/60 = 100\) revolutions per second. 2. Each revolution passes 7 pole pairs, so the electrical frequency is \(100 \times 7 = 700\,\text{Hz}\). 3. Six-step commutation switches \(6 \times 700 = 4200\) times per second. 4. Hall sensors 120° electrical apart sit \(120^\circ/7 = 17.1^\circ\) apart mechanically, because electrical angle equals mechanical angle times the number of pole pairs. Unlike a synchronous motor on the mains, the speed is not fixed: like a brushed dc motor, it rises with the supply voltage until back EMF balances it.
Common mistakes to avoid
First, thinking full-step drive halves the step angle; full stepping keeps the step angle and adds torque, while half stepping halves it. Second, assuming a stepper always knows where it is; overload, too-fast starts or resonance can lose steps unnoticed. Third, confusing electrical and mechanical degrees when placing Hall sensors: divide the electrical angle by the number of pole pairs. Fourth, assuming a 4-lead stepper can use a unipolar driver; it has no centre taps, so it needs bipolar drive. Fifth, treating BLDC motors as dc machines inside: their windings carry alternating currents.
Key takeaways
A stepper moves one step angle per drive change: steps per revolution = 360°/θ_step, and speed in rpm = step rate × 60 / steps per revolution. VR steppers have iron rotors and θ_step = |360°/N_r − 360°/N_s|; PM and hybrid steppers have magnets and detent torque. Half stepping doubles the steps; microstepping smooths motion. Steppers are open loop, so they home first and ramp their step rate. BLDC motors commutate electronically, timed by Hall sensors; electrical frequency = rev/s × pole pairs.
Flashcards
Flashcard
Turns one fixed step angle for each change in its winding currents
Test your understanding
Question 1 of 5
A stepper motor with a 1.8° step angle receives step pulses at 500 per second, one full step each. What is its shaft speed?
Question 2 of 5
A variable reluctance stepper has 6 stator poles (3 phases) and 4 rotor teeth. What is its step angle?
Question 3 of 5
A 200-step hybrid stepper is switched from full-step drive to half-step drive. What changes?
Question 4 of 5
A three-phase BLDC motor has 8 magnet poles. How far apart, in mechanical degrees, must Hall sensors be placed to sit 120° electrical apart?
Question 5 of 5
A printer's stepper axis is overloaded for a moment and the motor misses several steps. What does the controller know about this?
