Physics › Section O · Current and circuits › Topic O.4
AC versus DC, electric hazards, and nerve signals
The outlet in your wall does not deliver a steady current: in the US it runs through sixty full cycles a second, reversing direction twice in each. This topic explains how alternating current is described, why the grid uses it, what makes electricity dangerous to the body, and how the body's own nerves run on electrical signals.
Direct and alternating current
A battery gives direct current, DC: charge flows one way and, once steady, the current is constant. The mains supply gives alternating current, AC: the voltage, and with it the current, reverses direction periodically, following a sine curve:
Here \(V_0\) is the peak voltage and \(f\) the frequency. In the United States the mains frequency is 60 Hz and the standard outlet supplies 120 V; much of the rest of the world uses 230 V at 50 Hz. In a resistor the current rises and falls in step with the voltage, and the power \(IV\) pulses between zero and a maximum twice per cycle.
Root mean square values
A sine wave averages to zero over a cycle, so supplies are described by the root mean square instead: square the quantity, take its mean, and take the square root. For a sine wave,
The rms value is the steady DC value that would deliver the same average power to a resistor. So with rms values, Ohm's law and all the DC power formulas work unchanged: \(P_{\text{ave}} = I_{\text{rms}}V_{\text{rms}}\), which equals \(\tfrac{1}{2}I_0V_0\). Quoted mains voltages are rms: the US 120 V supply peaks at \(120\sqrt{2} = 170\) V.
Worked example: a hair dryer
A 1200 W hair dryer runs on the US 120 V rms supply. Treat it as a resistor. Find the rms and peak currents, its resistance and its peak power. 1. rms current: \(I_{\text{rms}} = 1200/120 = 10.0\) A. 2. Peak current: \(I_0 = \sqrt{2} \times 10.0 = 14.1\) A. 3. Resistance: \(R = V_{\text{rms}}/I_{\text{rms}} = 12.0\ \Omega\). 4. Peak power: \(I_0V_0 = 2 \times 1200 = 2400\) W. 5. Check: the power swings between 0 and 2400 W, and its average is half the peak, 1200 W, matching the rating.
Why the grid uses AC
Transmission lines have resistance, so they lose \(I^2R\) as heat. For a given power \(P = IV\), a higher voltage needs a smaller current, and the loss falls with the square of that current. AC voltages are easy to raise and lower with transformers, explained in a later topic, so electricity is generated at moderate voltage, stepped up to hundreds of kilovolts for transmission, and stepped down to 120 V near homes. This is why AC won out over Thomas Edison's DC systems in the 1890s, although modern electronics now make high-voltage DC practical for some very long lines and undersea cables.
Worked example: transmission losses
A power station sends 50.0 MW through lines with a total resistance of 4.00 Ω. Compare the losses at 345 kV and at 69.0 kV. 1. At 345 kV:
2. Loss:
which is 0.168% of the power sent. 3. At 69.0 kV: \(I = 725\) A, and the loss is \(725^2 \times 4.00 = 2.10 \times 10^6\) W, or 4.20%. 4. Check: the voltage is 5 times lower, so the current is 5 times higher and the loss \(5^2 = 25\) times higher, and \(0.168\% \times 25 = 4.20\%\).
Thermal hazards
Fires start when electrical energy becomes heat faster than it can escape. A short circuit is a very low-resistance path across a source, for example where worn insulation lets two wires touch. With \(P = V^2/R\), a 0.050 Ω short across 120 V would draw 2400 A and dissipate 288 kW if nothing stopped it. Overloading is quieter: too many devices on one circuit push too much current through its wiring. Fuses and circuit breakers guard against both by opening the circuit above a set current, typically 15 or 20 A for US household circuits.
Shock hazards
A shock is current through the body, and the current, not the voltage, sets its effects, along with the path, the duration and the frequency. The body is most sensitive near 50 to 60 Hz. Approximate effects for about 1 s at 60 Hz across the trunk of an adult are: about 1 mA can be felt; from about 10 to 20 mA muscles may clamp so a person cannot let go; from roughly 100 mA the heart may go into ventricular fibrillation, an uncoordinated quivering that stops blood flow. Very large currents, several amperes, clamp the heart entirely, which is how a defibrillator resets it. These figures vary between people and are for understanding only, not safety guidance.
Worked example: dry and wet skin
Most of the body's resistance is in dry skin, and water lowers it greatly. Using illustrative values, find the current through a person who touches 120 V with a total body resistance of 50 kΩ when dry, and 2.0 kΩ when wet. 1. Dry: \(I = 120/(5.0 \times 10^4)\), which is 2.4 mA, felt but below the let-go range. 2. Wet: \(I = 120/(2.0 \times 10^3)\), which is 60 mA, well past the let-go level. 3. Check: 25 times less resistance gives 25 times more current. This is why US codes require ground fault circuit interrupters, which cut the power when about 5 mA leaks, in bathrooms, kitchens and outdoors.
Nerve cells and the resting potential
Nerves signal with ions rather than electrons. A neuron's membrane, about 8 nm thick, separates fluids with different ion concentrations: more potassium ions, \(\mathrm{K^+}\), inside and more sodium ions, \(\mathrm{Na^+}\), outside. Because the resting membrane lets \(\mathrm{K^+}\) leak out more easily than \(\mathrm{Na^+}\) leaks in, a layer of charge builds up, and the inside sits at about −70 mV relative to the outside. Across 8 nm that is a field of roughly \(0.070/(8 \times 10^{-9}) \approx 9 \times 10^6\) V/m. Ion pumps in the membrane use energy to keep the concentration differences in place.
Action potentials and myelin
When a stimulus pushes the membrane past a threshold, sodium channels open, \(\mathrm{Na^+}\) rushes in and the inside swings to about +30 mV, then potassium channels open and \(\mathrm{K^+}\) flowing out restores the resting value, all within a few milliseconds. This pulse is the action potential, and each one triggers the next patch of membrane, so the signal travels along the axon. In thin bare axons it moves at around 1 m/s. Many axons are wrapped in insulating myelin, and the signal leaps between gaps called nodes of Ranvier at up to about 100 m/s. A 1.0 m path takes about 1 s at the slow speed but only 10 ms at the fast one. Heart muscle cells also fire in a coordinated wave, which an electrocardiogram, ECG, records from skin electrodes.
Common mistakes to avoid
First, using peak values in power formulas meant for rms: \(P_{\text{ave}} = I_{\text{rms}}V_{\text{rms}}\), and the US 120 V is already rms. Second, dividing by 2 instead of \(\sqrt{2}\) to get rms from peak. Third, thinking high voltage alone determines danger; current, path and duration matter. Fourth, forgetting that transmission losses depend on the current squared. Fifth, picturing nerve signals as electrons flowing along a wire; they are ions crossing the membrane.
Key takeaways
DC flows one way; AC reverses sinusoidally, at 60 Hz and 120 V rms in the US. For a sine wave, V_rms = V₀/√2 and I_rms = I₀/√2, and with rms values the DC formulas apply. The grid uses high voltage to cut I²R losses, and AC because transformers change its voltage easily. Shorts and overloads are thermal hazards, stopped by fuses and breakers. Shock effects depend on current, path, duration and frequency. Neurons rest near −70 mV, fire action potentials, and myelin speeds signals.
Flashcards
Flashcard
Direct current: charge flows in one direction only
Test your understanding
Question 1 of 5
An AC voltage has a peak value of 170 V. What is its rms value?
Question 2 of 5
A 600 W appliance runs on 120 V rms. What is the peak current, treating it as a resistor?
Question 3 of 5
A fixed power is sent along the same transmission line at 4 times the original voltage. How does the power lost in the line change?
Question 4 of 5
Which quantity mainly determines the effects of an electric shock, for a fixed path, duration and frequency?
Question 5 of 5
A nerve signal travels 0.50 m along a myelinated axon at 100 m/s and the same distance along a bare axon at 1.0 m/s. How long does each take?
