Physics › Section O · Current and circuits › Topic O.5
Resistors in series and parallel
Real circuits rarely hold just one resistor. By learning how resistors combine in series and in parallel, you can replace a whole network with a single equivalent resistance and find every current and voltage in it.
Two basic ways to connect
Resistors can be connected end to end, so that the same charge must pass through each one in turn: that is a series connection, with only one path. Or they can be connected side by side between the same two points, so that charge can take any one of several routes: that is a parallel connection. Most circuits mix the two. The aim in each case is the equivalent resistance, the single resistance that would draw the same current from the same source. Throughout this topic the battery is treated as ideal, with no internal resistance, and the connecting wires as having none; the next topic removes the first assumption.
Resistors in series
In series, the current \(I\) is the same through every resistor, because charge has nowhere else to go. Energy conservation means the voltage drops across the resistors add up to the source voltage: \(V = IR_1 + IR_2 + IR_3\). Dividing by \(I\) gives the equivalent resistance:
So series resistance is always larger than any single resistor in the chain. Each resistor takes a share of the voltage in proportion to its resistance, so the largest resistor has the largest voltage drop and, from \(P = I^2R\), dissipates the most power. Break the chain anywhere and the current stops everywhere.
Worked example: three in series
Resistors of 4.0 Ω, 6.0 Ω and 10.0 Ω are in series across a 12.0 V battery. Find the current, each voltage drop and the total power. 1. Equivalent resistance: \(R_s = 4.0 + 6.0 + 10.0 = 20.0\ \Omega\). 2. Current: \(I = V/R_s = 12.0/20.0 = 0.600\) A. 3. Drops: \(IR\) gives 2.40 V, 3.60 V and 6.00 V. 4. Powers: \(I^2R\) gives 1.44 W, 2.16 W and 3.60 W, totalling 7.20 W. 5. Check twice: the drops add to \(2.40 + 3.60 + 6.00 = 12.0\) V, and the battery supplies \(P = IV = 0.600 \times 12.0 = 7.20\) W, equal to the total dissipated.
Resistors in parallel
In parallel, every resistor is connected across the same two points, so each has the same voltage \(V\). Charge conservation means the branch currents add up to the total: \(I = V/R_1 + V/R_2 + V/R_3\). Dividing by \(V\) gives
Each extra path lets more current through, so the parallel resistance is always smaller than the smallest single resistor. For exactly two resistors this becomes the product over the sum, \(R_p = R_1R_2/(R_1 + R_2)\): 12 Ω and 6.0 Ω give 4.0 Ω, while in series they give 18 Ω. The smallest resistor carries the largest current.
Worked example: three in parallel
Resistors of 12.0 Ω, 6.0 Ω and 4.0 Ω are in parallel across a 12.0 V battery. Find the equivalent resistance, the branch currents and the total current. 1. Reciprocals:
so \(R_p = 2.0\ \Omega\). Remember to invert the sum. 2. Each branch has the full 12.0 V: the currents are \(12.0/12.0 = 1.00\) A, \(12.0/6.0 = 2.00\) A and \(12.0/4.0 = 3.00\) A. 3. Total: \(1.00 + 2.00 + 3.00 = 6.00\) A. 4. Check: \(V/R_p = 12.0/2.0 = 6.0\) A, in agreement, and 2.0 Ω is below the smallest resistor, 4.0 Ω, as it must be.
Parallel wiring at home
Household outlets and lights are wired in parallel. Every appliance then receives the full 120 V, each can be switched on or off without affecting the others, and one failed lamp does not darken the rest. But each appliance switched on adds another parallel path, lowering the total resistance and raising the total current in the supply wires. Plug in a kettle, a toaster and a microwave on one circuit and the current can exceed the breaker's limit. Some older strings of holiday lights were wired in series, so one failed bulb broke the circuit and the whole string went dark.
Combinations: reduce step by step
A mixed network is solved by simplifying it in stages. Find a group that is purely in series or purely in parallel, replace it by its equivalent, redraw, and repeat until one resistance remains. Then find the total current from the source and work back out through the stages, using Ohm's law at each one to recover the individual voltages and currents. Two checks keep you honest: at every junction the currents in must equal the currents out, and around any path from one battery terminal to the other the voltage drops must add to the battery voltage. Networks that cannot be reduced this way need Kirchhoff's rules, a later topic.
Worked example: a series-parallel network
A 12.0 V battery drives current through a 4.0 Ω resistor in series with a parallel pair of 6.0 Ω and 3.0 Ω. Find every current. 1. Parallel pair: \(R_p = \frac{6.0 \times 3.0}{6.0 + 3.0} = 2.0\ \Omega\). 2. Total: \(R = 4.0 + 2.0 = 6.0\ \Omega\), so \(I = 12.0/6.0 = 2.00\) A, which flows through the 4.0 Ω resistor. 3. Voltages: \(2.00 \times 4.0 = 8.0\) V across the 4.0 Ω resistor, leaving \(2.00 \times 2.0 = 4.0\) V across the pair. 4. Branches: \(4.0/6.0 = 0.67\) A and \(4.0/3.0 = 1.33\) A. 5. Check: \(0.67 + 1.33 = 2.00\) A at the junction, and \(8.0 + 4.0 = 12.0\) V around the path.
Reasoning about brightness
Identical lamps make a good test of understanding. Treat each as a fixed resistance \(R\), with brightness set by its power. Two in parallel across a battery of voltage \(V\) each get the full \(V\), so each dissipates \(V^2/R\). Two in series share the voltage, \(V/2\) each, so each dissipates \((V/2)^2/R = V^2/4R\), a quarter as much. The series pair glows dimly and the battery delivers less total power; the parallel pair glows brightly but drains the battery faster. Removing one lamp puts out the other in series but leaves it unchanged in parallel. Real filaments change resistance as they heat, so the factor is only approximately four.
Common mistakes to avoid
First, forgetting to invert: \(1/R_p\) is not \(R_p\); 1/12 + 1/6 + 1/4 = 1/2 means \(R_p = 2\ \Omega\). Second, a parallel answer larger than the smallest resistor, which is always wrong. Third, using the product-over-sum shortcut for three resistors at once; it works only for two. Fourth, assuming series resistors share the voltage equally when their resistances differ. Fifth, using the total current for a branch or the total voltage for a resistor that only gets part of it.
Key takeaways
Series resistors carry the same current, their voltages add, and R_s = R₁ + R₂ + ..., larger than any one. Parallel resistors share the same voltage, their currents add, and 1/R_p = 1/R₁ + 1/R₂ + ..., smaller than the smallest; for two, R_p = R₁R₂/(R₁ + R₂). Reduce mixed networks step by step, then work back out with Ohm's law, checking currents at junctions and voltages around paths. Household circuits are parallel, so every device gets the full voltage. Identical lamps in series each get a quarter of the power they would in parallel.
Flashcards
Flashcard
One path: the same current through each resistor
Test your understanding
Question 1 of 5
Resistors of 20 Ω, 30 Ω and 60 Ω are connected in parallel. What is their equivalent resistance?
Question 2 of 5
Resistors of 3.0 Ω, 5.0 Ω and 7.0 Ω are in series across an ideal 30.0 V battery. What is the voltage across the 7.0 Ω resistor?
Question 3 of 5
An ideal 12.0 V battery drives current through a 2.0 Ω resistor in series with two 8.0 Ω resistors in parallel. What current flows through each 8.0 Ω resistor?
Question 4 of 5
A third resistor is connected in parallel with two others across an ideal battery. What happens to the total current from the battery?
Question 5 of 5
Two identical lamps, treated as fixed resistors, are first connected in series and then in parallel across the same ideal battery. How does the power of each lamp in series compare with each lamp in parallel?
