Physics › Section O · Current and circuits › Topic O.3

Electric power and energy

A heater, a lamp and a phone charger all plug into the same outlet, yet they use energy at very different rates. Electric power ties that rate to current and voltage, and it is what the number on every appliance label and every electricity bill is about.

Energy carried by charge

Two facts from earlier topics combine here. A potential difference of 1 volt means that each coulomb of charge gains or loses 1 joule of energy in moving between two points. A current of 1 ampere means 1 coulomb passes each second. So when 1 A flows through a 1 V potential difference, 1 joule is transferred every second, which is 1 watt. In a circuit, the source gives energy to the moving charge, and the components convert it: a heater into thermal energy, a lamp into light and heat, a motor into mechanical work. Electric power is the rate of that transfer.

P = IV

When charge \(\Delta Q\) moves through a potential difference \(V\), the energy transferred is \(\Delta Q\,V\). Dividing by the time taken, and using \(I = \Delta Q/\Delta t\), gives the power:

P = IV

This holds for any device, whether it is a resistor, a motor or a battery being charged. The units check: \(\mathrm{A} \times \mathrm{V} = \mathrm{(C/s)(J/C)} = \mathrm{J/s} = \mathrm{W}\). A 60 W lamp designed for 120 V therefore draws \(I = P/V = 60/120 = 0.50\) A. The power rating on an appliance is the power it uses at its rated voltage.

Three forms for a resistor

For a resistor, Ohm's law \(V = IR\) lets you write the power two more ways:

P = IV = I^2R = \frac{V^2}{R}

All three give the same answer; choose the one that uses what you know. \(I^2R\) is handy when the current is fixed, such as in wires carrying a known current. \(V^2/R\) is handy when the voltage is fixed, as at a wall outlet. Notice what they predict. At a fixed voltage, a smaller resistance means more power, so a heater has a lower resistance than a lamp on the same supply. The 60 W, 120 V lamp has a hot resistance of \(120^2/60 = 240\ \Omega\).

Worked example: a space heater

A heater is rated 1500 W at 120 V. Find its current and resistance, and its power if the supply sags to 110 V, assuming its resistance stays the same. 1. Current: \(I = P/V = 1500/120 = 12.5\) A. 2. Resistance: \(R = V/I = 120/12.5 = 9.60\ \Omega\). 3. New power:

P = \frac{V^2}{R} = \frac{110^2}{9.60} = 1260\ \mathrm{W}

4. Check: the voltage fell by about 8%, and since power depends on \(V^2\), it falls by about 16%, and \(1500 \times 0.84 = 1260\). A heater drawing 12.5 A uses most of a 15 A household circuit, which is why running two on one circuit trips the breaker.

Where the energy goes

In a resistor all the electrical energy becomes thermal energy, an effect called Joule heating. Kettles, toasters and hair dryers are built to do exactly this. In many other devices the heating is waste. An old incandescent bulb converts well under 10% of its input to visible light; an LED lamp of about 9 W gives roughly the light of a 60 W incandescent. Electric motors in good condition convert most of their input into mechanical work. The power rating on a label tells you the rate of energy input, not how much of it does the job you want.

Energy, kilowatt-hours and cost

As the earlier topic on power showed, energy is power multiplied by time, \(E = Pt\), and electricity companies bill in kilowatt-hours, where \(1\ \mathrm{kWh} = 3.6 \times 10^6\) J. To find the cost, multiply the power in kilowatts by the hours of use, then by the price per kWh. Prices vary by state and season; this topic assumes a typical US residential price of $0.17 per kWh. A device rated in amperes at 120 V can be converted to watts first with \(P = IV\).

Worked example: switching to LED

A 60.0 W incandescent bulb and a 9.0 W LED bulb each run 5.00 hours a day for 365 days, with electricity at $0.17 per kWh. Compare the yearly costs. 1. Hours of use: \(5.00 \times 365 = 1825\) h. 2. Energy: incandescent \(0.0600 \times 1825 = 109.5\) kWh; LED \(0.0090 \times 1825 = 16.4\) kWh. 3. Costs: \(109.5 \times \$0.17 = \$18.62\) and \(16.425 \times \$0.17 = \$2.79\). 4. Saving: the 93.1 kWh difference costs $15.82 a year for one bulb. 5. Check: the LED uses \(9/60 = 15\%\) of the power, and $2.79 is 15% of $18.62. Over a house with twenty bulbs the saving is substantial.

Worked example: a phone battery

A phone battery is rated 4000 mAh at a nominal 3.85 V. How much energy does it store, and what does a full charge cost at $0.17 per kWh, ignoring charger losses? 1. Charge: \(Q = (4.000)(3600) = 1.44 \times 10^4\) C. 2. Energy:

E = QV = (1.44 \times 10^4)(3.85) = 5.54 \times 10^4\ \mathrm{J}

3. In kWh:

\frac{5.544 \times 10^4}{3.6 \times 10^6} = 0.0154\ \mathrm{kWh}

the same as 15.4 Wh. 4. Cost: \(0.0154 \times \$0.17\), about $0.0026, a quarter of a cent. 5. Check: 4.000 A h times 3.85 V is 15.4 W h directly.

Heating in wires and cords

Connecting wires have small resistances, but they carry the full current, so they dissipate \(I^2R\) too. An extension cord with a total resistance of \(0.10\ \Omega\) carrying the 12.5 A of a heater dissipates \(12.5^2 \times 0.10 = 15.6\) W along its length. Because of the square, doubling the current quadruples the heating. Too much current in thin wiring can overheat insulation, which is why high-power appliances need heavier cords and why circuits are protected by fuses and breakers, discussed in the next topic.

Common mistakes to avoid

First, using \(I^2R\) with the wrong resistance: in a cord problem, \(R\) is the cord's resistance, not the appliance's. Second, forgetting to square: \(P = I^2R\), not \(IR\), which is a voltage. Third, assuming a device keeps its rated power at a different voltage; at fixed resistance, power scales with \(V^2\). Fourth, mixing watts and kilowatts, or minutes and hours, in a kWh cost. Fifth, thinking a lower-resistance device uses less power on the same outlet; at fixed voltage it uses more.

Key takeaways

Electric power is the rate of energy transfer, P = IV, in watts, for any device. For a resistor, P = I²R = V²/R; choose the form that matches what is known. At a fixed voltage a lower resistance gives more power, and at a fixed resistance power scales with V². Resistors turn electrical energy into thermal energy. Energy is E = Pt, billed in kWh (1 kWh = 3.6 × 10⁶ J), and cost is kWh × price. Battery energy is charge × voltage. Wires dissipate I²R, so heating grows with the square of the current.

Flashcards

Flashcard

Electric power, P

Rate of electrical energy transfer: P = IV

Holds for any device.

Test your understanding

Question 1 of 5

A current of 2.50 A flows through an 8.0 Ω resistor. At what rate is energy dissipated?

Question 2 of 5

A 100 W lamp is designed for 120 V. What current does it draw at that voltage?

Question 3 of 5

What is the resistance of a heater rated 1500 W at 120 V?

Question 4 of 5

A 1200 W microwave runs 0.500 hours a day for 30 days. At $0.17 per kWh, what does that cost?

Question 5 of 5

The current in an extension cord rises from 5.0 A to 10.0 A. What happens to the rate of heating in the cord?

← Previous topicNext topic →