Physics › Section O · Current and circuits › Topic O.1

Electric current

Every phone, lamp and motor runs on charge that moves. Electric current measures how much charge passes a point each second, and it is the starting quantity for everything else in circuits.

Charge on the move

The earlier topics on charge and potential dealt mostly with charges at rest. A circuit is different: a battery or power supply keeps charges moving around a closed conducting path, and that steady flow lets energy be delivered to a lamp, a heater or a motor. Break the path anywhere, as a switch does, and the flow stops everywhere at once. To describe circuits we need a measure of how much charge flows. That measure is the current, and this topic defines it, links it to the motion of the charges themselves, and explains why lights come on instantly even though the charges crawl.

Defining current

Current is the rate at which charge passes through a cross-section of a conductor:

I = \frac{\Delta Q}{\Delta t}

The SI unit is the ampere, A, and \(1\ \mathrm{A} = 1\ \mathrm{C/s}\). Since 2019 the SI fixes the elementary charge at exactly \(e = 1.602176634 \times 10^{-19}\) C, which in turn defines the ampere. Rough scales help: an indicator LED carries about 20 mA, a phone charges at one to three amperes, a household circuit is protected at 15 or 20 A, a car's starter motor briefly draws a few hundred amperes, and a lightning stroke reaches tens of thousands. Rearranged, \(\Delta Q = I\Delta t\) gives the charge that flows in a given time.

Worked example: counting electrons

A torch bulb carries a steady 0.250 A for 3.00 minutes. How much charge passes through it, and how many electrons is that? 1. Convert the time to seconds: \(\Delta t = 3.00 \times 60 = 180\) s. 2. Charge: \(\Delta Q = I\Delta t = (0.250)(180) = 45.0\) C. 3. Each electron carries \(1.602 \times 10^{-19}\) C, so the number is

N = \frac{45.0}{1.602 \times 10^{-19}} = 2.81 \times 10^{20}

4. Check: one ampere is about \(6.24 \times 10^{18}\) electrons per second, and

0.250 \times 180 \times 6.24 \times 10^{18} = 2.81 \times 10^{20}

Even a modest current involves an enormous number of carriers, which is why we never notice them individually.

Conventional current and electron flow

By convention, current flows in the direction positive charge would move: out of the positive terminal of a battery, through the circuit, and back into the negative terminal. The convention dates from Benjamin Franklin's choice of which charge to call positive, long before electrons were known. In metal wires the moving charges are in fact electrons, which drift the other way, from the negative terminal round to the positive one. The two descriptions give identical results for currents, energy and power. In salt solutions, battery electrolytes and nerve cells, positive and negative ions move in opposite directions and both contribute to the same conventional current.

Drift velocity

The free electrons in a metal already move randomly at about \(10^6\) m/s, colliding constantly with the vibrating ions, but with no field their average velocity is zero. A field in the wire adds a small average motion, the drift velocity \(v_d\), opposite to the field for electrons. Picture a length \(v_d\Delta t\) of wire with cross-sectional area \(A\) and \(n\) free carriers per cubic metre, each of charge \(q\). In time \(\Delta t\) all of its charge, \(nqAv_d\Delta t\), passes the end, so

I = nqAv_d

For a given current, more carriers or a thicker wire means a slower drift.

Worked example: drift in a copper wire

A copper wire of diameter 1.63 mm, a common size in house wiring, carries 10.0 A. Copper has about one free electron per atom, giving \(n = 8.49 \times 10^{28}\ \mathrm{m^{-3}}\). Find the drift speed. 1. Area:

A = \pi r^2 = \pi(0.815 \times 10^{-3})^2 = 2.087 \times 10^{-6}\ \mathrm{m^2}

2. Rearrange: \(v_d = \frac{I}{nqA}\). 3. Substitute:

v_d = \frac{10.0}{(8.49 \times 10^{28})(1.602 \times 10^{-19})(2.087 \times 10^{-6})}

which is \(3.52 \times 10^{-4}\) m/s, about a third of a millimetre per second. 4. Check: at that speed an electron needs about 2840 s, roughly 47 minutes, to drift one metre, consistent with drift speeds well below 1 mm/s.

Why the lights come on at once

If electrons take most of an hour to drift a metre, why does a lamp light the instant you flip the switch? Because the wire is already full of free electrons. Closing the switch sets up the electric field along the whole circuit almost immediately; that change in field travels at a large fraction of the speed of light, and electrons everywhere in the loop start drifting together. A garden hose that is already full of water behaves the same way: water leaves the nozzle as soon as the tap opens, although no water from the tap has arrived yet. The signal is fast; the carriers are slow.

Worked example: a phone battery

Battery capacity is often stated in milliampere-hours, which is a unit of charge. A phone battery is rated at 5000 mAh. How much charge is that, and how long would it last at an average current of 0.625 A? 1. Convert:

5000\ \mathrm{mAh} = 5.000\ \mathrm{A} \times 3600\ \mathrm{s} = 1.80 \times 10^4\ \mathrm{C}

2. Time:

\Delta t = \frac{\Delta Q}{I} = \frac{1.80 \times 10^4}{0.625} = 2.88 \times 10^4\ \mathrm{s}

which is 8.00 hours. 3. Shortcut check: 5.000 A h divided by 0.625 A is 8.00 h directly. A heavier average load, such as 1.25 A while gaming, would halve the time to 4.00 h.

Common mistakes to avoid

First, leaving time in minutes or hours in \(I = \Delta Q/\Delta t\); amperes need seconds. Second, forgetting the milli- in mA or mAh, which puts an answer off by a factor of 1000. Third, thinking current is used up by a lamp: the same current flows in and out, and it is energy that the lamp converts. Fourth, confusing drift speed with signal speed. Fifth, squaring the wrong thing in \(A = \pi r^2\): use the radius, half the diameter, and convert millimetres to metres first. Sixth, assuming electrons flow the same way as conventional current in a metal.

Key takeaways

Current is the rate of flow of charge, I = ΔQ/Δt, measured in amperes, with 1 A = 1 C/s. The number of electrons is the charge divided by e = 1.602 × 10⁻¹⁹ C. Conventional current runs from positive to negative through the external circuit; in metals, electrons drift the opposite way. Current and drift speed are linked by I = nqAv_d, and drift speeds in wires are tiny, well under 1 mm/s, while the electric signal travels at a large fraction of the speed of light. Battery capacity in mAh is a measure of charge.

Flashcards

Flashcard

Electric current, I

The rate of flow of charge: I = ΔQ/Δt

Charge passing a cross-section per second.

Test your understanding

Question 1 of 5

A steady current of 2.00 A flows for 30.0 s. How much charge passes a point in the wire?

Question 2 of 5

A sensor draws a current of 1.60 mA. About how many electrons pass through it each second?

Question 3 of 5

In a copper wire connected to a battery, which way do the electrons drift?

Question 4 of 5

The same current flows through two copper wires, one with twice the diameter of the other. How does the drift speed in the thicker wire compare?

Question 5 of 5

A 4000 mAh battery supplies an average current of 0.500 A. About how long does it last?

← Previous topicNext topic →