Physics › Section O · Current and circuits › Topic O.2
Ohm's law, resistance, and resistivity
Connect the same battery to a copper wire and to a strip of rubber and you get wildly different currents. Resistance explains the difference, and it depends both on what a conductor is made of and on its shape and temperature.
Push and opposition
A potential difference across a conductor sets up an electric field inside it, and the field drives a current. How much current flows for a given voltage depends on the conductor. The free electrons drifting through a metal keep colliding with its vibrating ions, which hinders their motion and turns some of their energy into thermal energy. Resistance is the measure of that opposition:
Its SI unit is the ohm, \(\Omega\), where \(1\ \Omega = 1\ \mathrm{V/A}\). A large resistance lets only a small current through for a given voltage. In circuit diagrams, connecting wires are usually treated as having negligible resistance, so all of a battery's voltage appears across the components.
Ohm's law
In 1827 Georg Ohm reported that for many conductors the current is directly proportional to the voltage across them, so \(R\) stays constant:
Materials and devices that obey this are called ohmic, and a graph of \(I\) against \(V\) for them is a straight line through the origin with gradient \(1/R\). Ohm's law is not a universal law like conservation of charge; it is a description that many materials obey well at a fixed temperature. A diode is strongly non-ohmic: it conducts easily one way and hardly at all the other. A lamp filament is non-ohmic too, because its resistance rises as it heats. The product \(IR\) is often called the voltage drop across a resistor.
Worked example: a toaster element
A toaster element draws 8.00 A from a 120 V outlet. What is its resistance, and what current would it draw from a 60.0 V supply if its resistance stayed the same? 1. Rearrange Ohm's law: \(R = V/I = 120/8.00 = 15.0\ \Omega\). 2. At the lower voltage: \(I = V/R = 60.0/15.0 = 4.00\) A. 3. Check: for an ohmic conductor the current is proportional to the voltage, so halving the voltage should halve the current, and it does. In practice the element would run cooler at the lower current, its resistance would fall a little, and the real current would be slightly above 4.00 A.
Resistivity: material and shape
The resistance of a uniform wire or bar depends on its length \(L\), its cross-sectional area \(A\) and the material:
Here \(\rho\) is the resistivity, a property of the material alone, in ohm metres, \(\Omega\cdot\mathrm{m}\). A longer wire means more collisions along the way; a thicker wire offers more parallel paths, like extra lanes on a road. Approximate values at 20 °C, from standard tables, in \(\Omega\cdot\mathrm{m}\): silver \(1.59 \times 10^{-8}\), copper \(1.68 \times 10^{-8}\), gold \(2.44 \times 10^{-8}\), aluminium \(2.65 \times 10^{-8}\), tungsten \(5.60 \times 10^{-8}\), iron \(9.71 \times 10^{-8}\) and nichrome about \(1.10 \times 10^{-6}\). Pure silicon is near \(2.3 \times 10^{3}\), and glass ranges from about \(10^{10}\) to \(10^{14}\).
Conductors, semiconductors, insulators
Resistivities span more than twenty powers of ten, one of the widest ranges of any physical property. Metals are conductors because each atom contributes free electrons. Insulators such as glass and rubber have almost none. Semiconductors such as silicon and germanium sit in between, and adding tiny, controlled amounts of impurity changes their resistivity enormously, which is the basis of every computer chip. Copper is used for most wiring because it combines low resistivity with low cost; aluminium is used in overhead power lines because it is lighter for the same resistance. Nichrome, with its high resistivity, is chosen for heating elements, which need resistance in a compact coil.
Worked example: a length of copper wire
Find the resistance of 25.0 m of copper wire with diameter 1.63 mm, and the voltage drop along it when it carries 10.0 A. 1. Radius: \(r = 0.815\ \mathrm{mm} = 0.815 \times 10^{-3}\) m. 2. Area: \(A = \pi r^2 = 2.087 \times 10^{-6}\ \mathrm{m^2}\). 3. Resistance:
4. Voltage drop: \(V = IR = (10.0)(0.201) = 2.01\) V. 5. Check: a wire of twice the diameter has four times the area, so its resistance would be a quarter, \(0.0503\ \Omega\). A small resistance still matters at high current, which is why long runs of wire are made thicker.
Resistance and temperature
Resistivity changes with temperature. For modest changes, up to about 100 °C, it varies linearly:
where \(\rho_0\) is the value at the starting temperature and \(\alpha\) is the temperature coefficient of resistivity, in \(\mathrm{^\circ C^{-1}}\). The resistance of a given object follows the same rule, \(R = R_0(1 + \alpha\,\Delta T)\), because thermal expansion changes \(L\) and \(A\) far less. For metals \(\alpha\) is positive: hotter ions vibrate more and scatter electrons more often. Approximate values: copper \(4.0 \times 10^{-3}\), tungsten \(4.5 \times 10^{-3}\), nichrome about \(0.4 \times 10^{-3}\). For semiconductors \(\alpha\) is negative, because heating frees more charge carriers. Some materials become superconductors, with zero resistance, below a critical temperature: mercury below about 4.2 K.
Worked example: a platinum thermometer
Many laboratory and industrial thermometers measure the resistance of a platinum wire. A standard sensor has \(R_0 = 100.0\ \Omega\) at 0 °C and \(\alpha = 3.85 \times 10^{-3}\ \mathrm{^\circ C^{-1}}\). It reads 119.4 Ω. What is the temperature? 1. Rearrange \(R = R_0(1 + \alpha\,\Delta T)\):
2. Substitute:
3. Using this linear model, the temperature is 50.4 °C. 4. Check: each degree adds about 0.385 Ω, and \(50.4 \times 0.385 = 19.4\) Ω, matching the rise from 100.0 Ω. Thermistors, made from semiconductors, are used the same way, with resistance falling as temperature rises.
Common mistakes to avoid
First, using the diameter instead of the radius in \(A = \pi r^2\), which makes the area four times too large. Second, leaving millimetres unconverted: \(1\ \mathrm{mm^2} = 10^{-6}\ \mathrm{m^2}\). Third, confusing resistivity, a property of the material, with resistance, a property of a particular object. Fourth, putting the final temperature into \(\alpha\,\Delta T\) instead of the change in temperature. Fifth, assuming every device is ohmic: the resistance of a lamp filament changes as it heats. Sixth, writing \(R = V/I\) and calling it Ohm's law; that is the definition of resistance, and Ohm's law is the claim that it stays constant.
Key takeaways
Resistance is R = V/I, measured in ohms, 1 Ω = 1 V/A. Ohm's law, V = IR with R constant, describes ohmic conductors; diodes and hot filaments are non-ohmic. A uniform conductor has R = ρL/A, where the resistivity ρ, in Ω·m, depends only on the material: copper is about 1.68 × 10⁻⁸ Ω·m. Doubling the length doubles R, and doubling the diameter quarters it. For moderate temperature changes, R = R₀(1 + αΔT); α is positive for metals and negative for semiconductors, and superconductors have zero resistance below a critical temperature.
Flashcards
Flashcard
R = V/I, the opposition to current
Test your understanding
Question 1 of 5
A potential difference of 6.0 V across a component drives a current of 0.040 A. What is its resistance?
Question 2 of 5
Wire B is made of the same metal as wire A but is twice as long and has twice the diameter. How does the resistance of B compare with that of A?
Question 3 of 5
What is the resistance of 100 m of aluminium wire of diameter 2.00 mm? Take ρ = 2.65 × 10⁻⁸ Ω·m.
Question 4 of 5
A copper coil has a resistance of 10.0 Ω at 20 °C. Taking α = 4.0 × 10⁻³ per °C, what is its resistance at 120 °C?
Question 5 of 5
Why does the resistance of a pure semiconductor such as silicon fall as its temperature rises?
