Physics › Section C · Forces and Newton's laws › Topic C.7
Drag forces
Anything moving through air or water has to push the fluid out of its way, and the fluid pushes back. That push, called drag, grows quickly with speed, and it explains why falling objects stop speeding up and why cars burn more fuel on the motorway.
Friction from a fluid
Hold your hand out of the window of a moving car and you feel a backward force that grows as the car speeds up. That force is drag: the resistive force a fluid, a gas or a liquid, exerts on an object moving through it. Drag always points opposite to the object's velocity relative to the fluid. In that way it resembles kinetic friction, but there is one key difference. Kinetic friction between solid surfaces is nearly independent of speed, while drag depends strongly on speed. The same object can feel almost no drag when slow and a large drag when fast.
What drag depends on
Four things set the size of the drag force. Speed matters most. The frontal area \(A\), the area the object presents to the oncoming flow, matters because a bigger face pushes more fluid aside. The density of the fluid, \(\rho\), matters because in a denser fluid the object must shove more mass aside every second: water resists far more than air. Shape matters too, and it is captured by a dimensionless drag coefficient \(C\), measured in wind tunnels or water tanks rather than calculated. Turn your hand edge-on to the wind and both the area and the drag fall sharply.
The drag equation
For everyday objects such as cars, cyclists, balls and skydivers moving through air at ordinary speeds, measurements fit
The crucial feature is the square of the speed: double the speed and the drag becomes four times as large. Approximate drag coefficients are about 0.3 for a modern car, about 0.47 for a smooth sphere, about 0.9 for an upright cyclist and about 1.2 for a flat plate facing the flow. Near sea level, air has a density of about \(1.20\ \mathrm{kg/m^3}\). Treat \(C\) as constant for these problems, although in reality it changes somewhat with speed.
Worked example: a cyclist at two speeds
An upright cyclist with \(C = 0.90\) and a frontal area of \(0.50\ \mathrm{m^2}\) rides through still air of density \(1.20\ \mathrm{kg/m^3}\). Find the drag at 10.0 m/s and at 20.0 m/s. 1. At 10.0 m/s:
2. At 20.0 m/s, every factor is the same except \(v^2\), which is four times larger, so \(F_D = 4 \times 27.0 = 108\) N. 3. Check the units: \(\mathrm{kg/m^3} \times \mathrm{m^2} \times \mathrm{m^2/s^2}\) gives \(\mathrm{kg\,m/s^2}\), which is a newton. The fourfold rise explains why racing cyclists crouch low: a smaller \(A\) and a better shape cut the drag at every speed.
Streamlining and fuel use
Because drag grows as \(v^2\), it dominates at high speed. For a car on the motorway, air drag is usually the largest single force the engine works against, so driving a little slower saves a noticeable amount of fuel. Designers reduce drag by streamlining: rounding the front, tapering the rear and smoothing the underside so the air flows past without breaking into large swirls behind. Nature does the same, as the shapes of fish, dolphins and diving birds show. Sometimes high drag is the goal. A parachute is designed to have a very large area and drag coefficient.
Small and slow: drag proportional to speed
The \(v^2\) law fails for very small objects, very slow motion or very viscous (thick, sticky) fluids. Then the fluid flows smoothly round the object, and drag is proportional to the speed itself. For a small sphere of radius \(r\), Stokes's law gives
where \(\eta\) is the viscosity of the fluid. Pollen, dust, fog droplets and bacteria live in this regime, and so does a ball bearing sinking slowly through syrup. Some AP Physics problems model drag simply as \(F = bv\). Both laws are models that work in different ranges, not rival truths.
Terminal velocity
Drop an object from rest. At first it moves slowly, the drag is small and it accelerates at nearly \(g\). As it speeds up, drag grows, the net downward force \(mg - F_D\) shrinks, and so does the acceleration. The speed gets ever closer to the value at which drag equals weight. There the net force is zero, the acceleration is zero, and the object falls at a constant terminal velocity. Setting \(\tfrac{1}{2} C\rho A v_t^2 = mg\) and solving gives
A heavier object needs more drag, and so more speed, to balance its weight, while a larger area lowers the terminal velocity.
Worked example: a skydiver and a parachute
An 80.0 kg skydiver falls belly-down with \(C \approx 1.0\) and \(A \approx 0.50\ \mathrm{m^2}\) through air of density \(1.20\ \mathrm{kg/m^3}\). Estimate her terminal velocity, then the parachute area needed to land at 5.0 m/s if the canopy has \(C \approx 1.3\). 1.
about 180 km/h. 2. For the canopy, rearrange for area: \(A = \frac{2mg}{C\rho v_t^2}\). 3. Substitute: \(A = \frac{1568}{(1.3)(1.20)(25)} = 40\ \mathrm{m^2}\). 4. Check: real belly-down skydivers fall at roughly 50 to 60 m/s, and round canopies tens of square metres in area are typical, so both estimates are sensible.
Worked example: heavier but the same size
A table-tennis ball has a mass of 2.7 g and a diameter of 40 mm. Taking \(C = 0.47\) and air density \(1.20\ \mathrm{kg/m^3}\), find its terminal velocity, then predict it for a ball of the same size with four times the mass. 1. Frontal area: \(A = \pi r^2 = \pi(0.020)^2 = 1.26 \times 10^{-3}\ \mathrm{m^2}\). 2.
3. With the size unchanged, \(v_t\) depends on \(\sqrt{m}\), so four times the mass doubles it, to 17 m/s. 4. Check: at 8.6 m/s the drag, about 0.026 N, matches the ball's weight, \(0.0027 \times 9.80 = 0.026\) N.
Common mistakes to avoid
First, treating drag as constant like kinetic friction; it changes as the speed changes. Second, assuming drag doubles when speed doubles: in the \(v^2\) regime it quadruples. Third, thinking an object at terminal velocity has no forces on it. Drag and weight are both present and large; they simply balance. Fourth, forgetting the square root when solving for \(v_t\), or dropping the factor of \(\tfrac{1}{2}\). Fifth, believing that heavy and light objects always fall together. That is true only when drag is negligible; with air resistance and the same shape, the one with more mass per unit of frontal area wins.
Key takeaways
Drag is the resistive force of a fluid on an object moving through it, pointing opposite to the velocity relative to the fluid. For ordinary objects in air it is F_D = ½CρAv², so it rises with the square of the speed, the frontal area, the fluid density and a measured, dimensionless drag coefficient. Streamlining lowers C and A. For tiny, slow objects or thick fluids, drag is proportional to speed, as in Stokes's law, F_D = 6πηrv. A falling object speeds up until drag equals its weight and then falls at terminal velocity, v_t = √(2mg/(CρA)). Same size with more mass means a higher terminal velocity.
Flashcards
Flashcard
The resistive force of a fluid on an object moving through it
Test your understanding
Question 1 of 5
A car feels 90 N of air drag at 15 m/s. Assuming drag is proportional to v², what is the drag at 30 m/s?
Question 2 of 5
A skydiver is falling at her terminal velocity. Which statement is true?
Question 3 of 5
A 0.60 kg ball has C = 0.50 and a frontal area of 0.040 m². Using air density 1.20 kg/m³ and g = 9.80 m/s², what is its terminal velocity in the v² model?
Question 4 of 5
A ball has a terminal velocity of 10 m/s. A second ball has the same size and shape but four times the mass. What is its terminal velocity?
Question 5 of 5
Which of these is best described by drag proportional to speed, rather than to speed squared?
