Physics › Section C · Forces and Newton's laws › Topic C.8
Elasticity: stress and strain
Every force changes the shape of what it acts on, even if only by a fraction of a millimetre. Stress, strain and the elastic moduli let engineers predict how much a cable stretches, a beam bends or a liquid squeezes, and when a material will give way.
Forces change shape
Forces change shape as well as motion. A bridge cable lengthens slightly under traffic, a chair leg shortens a little when you sit, and a rubber band stretches a lot. A change of shape caused by a force is a deformation. If the object springs back once the load is taken away, the deformation is elastic; if it stays bent or stretched, it is plastic. For small deformations of most solids, a simple rule holds: the size of the deformation grows in step with the force.
Hooke's law
For a spring, or any object stretched or compressed by a small amount, the change in length \(\Delta L\) is proportional to the applied force:
The constant \(k\), the spring constant or stiffness, is measured in N/m; a stiff spring has a large \(k\). The spring pulls back with an equal restoring force directed opposite to the stretch, often written \(F = -kx\), where the minus sign shows the direction. A graph of force against extension is a straight line through the origin, and its slope is \(k\). Hooke's law is a model that holds only up to a limit, beyond which the graph curves.
Worked example: calibrating a spring
Hanging a 0.500 kg mass from a spring stretches it by 4.00 cm. Find \(k\), then the stretch with a 0.800 kg mass. 1. At rest, the spring force balances the weight: \(F = mg = 0.500 \times 9.80 = 4.90\) N. 2. Convert the stretch to metres, 0.0400 m, so \(k = \frac{4.90\ \mathrm{N}}{0.0400\ \mathrm{m}} = 123\) N/m. 3. The new force is \(0.800 \times 9.80 = 7.84\) N, so \(\Delta L = \frac{7.84}{122.5} = 0.0640\) m, or 6.40 cm. 4. Check by proportion: the mass rose by a factor of 1.6, and so did the stretch, from 4.00 cm to 6.40 cm, as long as the spring stays within its limit.
Stress and strain
A spring constant describes one object. To describe a material, remove the effect of size: a thick rod stretches less than a thin one under the same load, and a long rod more than a short one. Stress is the force per unit cross-sectional area, \(\frac{F}{A}\), measured in pascals (\(1\ \mathrm{Pa} = 1\ \mathrm{N/m^2}\)). Strain is the fractional change in length, \(\frac{\Delta L}{L_0}\), where \(L_0\) is the original length. Strain is a ratio of two lengths, so it has no units; a strain of 0.001 means a stretch of 0.1%.
Young's modulus
For stretching (tension) or squashing (compression) along a length, stress is proportional to strain in the elastic range:
The constant \(Y\) is Young's modulus, a property of the material alone, in pascals. Rearranged,
so the stretch grows with the load and the original length, and falls with the area and the stiffness of the material. This is Hooke's law again, with \(k = \frac{YA}{L_0}\).
Typical elastic moduli
Moduli are measured, vary with composition and treatment, and are usually quoted in gigapascals (\(1\ \mathrm{GPa} = 10^9\) Pa). Standard approximate values for Young's modulus, shear modulus and bulk modulus are: steel, 200, 80 and 160 GPa; aluminium, 70, 26 and 76 GPa; copper, 120, 45 and 140 GPa. Compact bone has a Young's modulus of roughly 15 to 20 GPa along its length but a shear modulus of only a few GPa (some tables wrongly print 80 GPa), and rubber only about 0.01 to 0.1 GPa, which is why it stretches so easily. Water has a bulk modulus of about 2.2 GPa. Treat any result from these as an estimate to two figures.
Worked example: a steel wire under load
A steel wire 2.00 m long and 1.00 mm in diameter hangs a 10.0 kg mass. Taking \(Y = 200\) GPa, how much does the wire stretch? 1. Area: \(A = \pi r^2 = \pi(0.000500)^2 = 7.85 \times 10^{-7}\ \mathrm{m^2}\). 2. Load: \(F = 10.0 \times 9.80 = 98.0\) N. 3. Stress: \(\frac{98.0}{7.85 \times 10^{-7}} = 1.248 \times 10^8\) Pa, about 125 MPa. 4. Strain: \(\frac{1.248 \times 10^8}{2.00 \times 10^{11}} = 6.24 \times 10^{-4}\). 5. Stretch: \(\Delta L = 6.24 \times 10^{-4} \times 2.00 = 1.25 \times 10^{-3}\) m, or 1.25 mm. 6. Check: the strain is well under 0.1%, so the elastic model is reasonable, and the stress is below the strength of ordinary steel.
Shear: a sideways deformation
In shear, forces act parallel to opposite faces of an object, in opposite directions, like pushing the top of a thick book sideways while its bottom stays put. The faces slide a distance \(\Delta x\) relative to each other, across a separation \(L_0\). For small deformations,
with \(A\) the area of each sheared face and \(S\) the shear modulus. For common metals, \(S\) is roughly 0.35 to 0.4 times \(Y\). Liquids and gases have a shear modulus of essentially zero: they cannot resist a steady sideways stress, so they flow, which is what makes them fluids.
Bulk modulus: squeezing from all sides
When the pressure on an object rises by \(\Delta P\) on every side, as under deep water, its volume shrinks by \(\Delta V\):
The minus sign shows that a rise in pressure reduces the volume, and \(B\) is the bulk modulus. For example, the water in a hydraulic system at 20 MPa above normal pressure, with \(B = 2.2\) GPa, shrinks by only \(\frac{20 \times 10^6}{2.2 \times 10^9} = 0.0091\), less than 1%. Liquids are nearly incompressible, which is why they transmit force so well. Gases compress far more easily, and their bulk modulus depends on the conditions.
Beyond the elastic range
Stress and strain stay in proportion only up to the proportional limit. A little beyond it, a material may still spring back fully, up to its elastic limit. Past that, deformation is plastic: a bent paper clip stays bent. More load reaches the ultimate strength, the greatest stress the material can bear, and then it fractures. Ductile materials such as copper deform a long way first; brittle ones such as glass snap with little warning. Structural steel has an ultimate tensile strength of roughly 400 to 550 MPa, and engineers design to stay well below it.
Common mistakes to avoid
First, using the diameter where the formula needs the radius, or forgetting that area grows as the radius squared: doubling a wire's diameter makes it four times harder to stretch, not twice. Second, mixing units: moduli are given in GPa, so convert to pascals, and lengths in millimetres must become metres. Third, treating strain as having units; it is a pure ratio. Fourth, confusing stress, a force per area, with force itself. Fifth, applying Hooke's law past the proportional limit, where stress is no longer proportional to strain.
Key takeaways
A deformation is elastic if the object returns to its shape and plastic if it does not. Hooke's law, F = kΔL, holds for small deformations. Stress is F/A in pascals, and strain is ΔL/L₀ with no units. In tension and compression, stress = Y × strain, so ΔL = FL₀/(YA). In shear, F/A = S Δx/L₀, and fluids have S of essentially zero. Under all-round pressure, ΔP = −B ΔV/V₀, and liquids have large bulk moduli. Approximate values: steel Y ≈ 200 GPa, aluminium Y ≈ 70 GPa, water B ≈ 2.2 GPa. Beyond the proportional and elastic limits, materials deform permanently and finally fracture.
Flashcards
Flashcard
A change in an object's shape caused by a force
Test your understanding
Question 1 of 5
A 6.0 N force stretches a spring by 3.0 cm. Within the Hooke's law range, how far does a 15 N force stretch it?
Question 2 of 5
An aluminium rod 1.50 m long, with cross-sectional area 2.0 × 10⁻⁴ m², carries a tension of 7000 N. Taking Y = 70 GPa, how much does it stretch?
Question 3 of 5
Two steel wires of the same length carry the same load, but wire B has twice the diameter of wire A. How does the stretch of B compare with that of A?
Question 4 of 5
Water has a bulk modulus of about 2.2 GPa. By what fraction does its volume decrease when the pressure on it rises by 11 MPa?
Question 5 of 5
Why does a liquid flow instead of holding its shape when a steady sideways force acts on it?
