Physics › Section C · Forces and Newton's laws › Topic C.6

Friction

Friction is why a heavy sofa refuses to budge, why a car can stop, and why you can walk at all. Two simple models, one for surfaces at rest and one for surfaces sliding, let you put it into Newton's laws.

A force along the surface

Friction is the force between two surfaces in contact that opposes their relative motion, or the motion they would have without it. It acts parallel to the surface, at right angles to the normal force. There are two kinds. Static friction acts while the surfaces are not slipping over each other, and kinetic friction acts once they slide. Friction is often a nuisance, wasting energy and wearing out machine parts, but without it shoes, tyres and brakes would all be useless.

Where friction comes from

Even polished surfaces are rough on a microscopic scale, so two objects in contact touch only at the tips of their highest bumps. The true area of contact is far smaller than the area you see. At those points the surface atoms attract one another, and bumps catch and must ride over or break off. Pressing the surfaces together harder flattens the bumps and enlarges the real contact area, which is why friction grows with the normal force. The same reasoning explains a surprising result: in the simple model, friction does not depend on the apparent area of contact.

Static friction is an inequality

Push gently on a heavy crate and it stays put, because static friction pushes back exactly as hard as you push. Static friction is a responsive force: it takes whatever value, from zero up to a maximum, keeps the surfaces from slipping.

f_s \le \mu_s F_N

In this inequality \(F_N\) is the normal force and \(\mu_s\), a number fixed by the two materials, is called the coefficient of static friction. The equals sign holds only at the point of slipping. If the largest possible static friction on a crate is 150 N and you push with 60 N, the friction is 60 N, not 150 N. Only when your push exceeds \(\mu_s F_N\) does the crate start to move.

Kinetic friction

Once the surfaces slide, the friction is kinetic, and in the simple model it has a fixed size:

f_k = \mu_k F_N

Here \(\mu_k\) is the coefficient of kinetic friction. Kinetic friction points opposite to the sliding and is nearly independent of speed at everyday speeds. For most pairs of surfaces \(\mu_k < \mu_s\), so it is easier to keep a crate moving than to start it. Both coefficients are ratios of two forces, so they have no units; most lie between 0 and 1, though racing tyres can exceed 1. Friction is simply one more force in the problem-solving routine. For a block on a table pulled by a hanging mass, kinetic friction on the block gives

a = \frac{m_2 g - \mu_k m_1 g}{m_1 + m_2}

Typical coefficients

Coefficients are measured, not calculated, and depend on the surface finish, cleanliness, moisture and temperature, so tables give approximate values to one or two figures. Standard approximate values (static, then kinetic) are: rubber on dry concrete, 1.0 and 0.8; rubber on wet concrete, 0.7 and 0.5; wood on wood, 0.4 and 0.2; dry steel on steel, 0.7 and 0.6; ice on ice, 0.1 and 0.03; Teflon on Teflon, 0.04 and 0.04. Lubricated human joints are lower still, around 0.01. Car tyres on dry asphalt behave much like rubber on dry concrete, with \(\mu_s\) roughly 0.7 to 1.0. Published tables disagree by 0.1 or more: some list 0.7 for kinetic rubber on dry concrete, or 0.3 for kinetic dry steel on steel. Treat any answer computed from these as an estimate.

Worked example: starting and keeping a crate moving

A 40.0 kg crate sits on a level wooden floor with \(\mu_s = 0.40\) and \(\mu_k = 0.20\). Is a horizontal 100 N push enough to move it? What happens with a 200 N push? 1. The floor is level and the push horizontal, so \(F_N = mg = 40.0 \times 9.80 = 392\) N. 2. Maximum static friction: \(\mu_s F_N = 0.40 \times 392 = 157\) N. 3. A 100 N push is below that, so the crate stays at rest and static friction is exactly 100 N. 4. A 200 N push exceeds 157 N, so the crate slides. Kinetic friction is \(0.20 \times 392 = 78.4\) N. 5. Net force: \(200 - 78.4 = 121.6\) N, so \(a = 121.6 \div 40.0 = 3.04\) m/s². 6. Check: the acceleration is less than the frictionless value of 5.00 m/s², as it should be.

Friction on a slope

On a slope at angle \(\theta\), the normal force is \(F_N = mg\cos\theta\), and the part of the weight pulling the block downhill is \(mg\sin\theta\). A block stays at rest while static friction can balance that component, that is while \(mg\sin\theta \le \mu_s mg\cos\theta\). Cancelling \(mg\), it is on the point of slipping when

\tan\theta = \mu_s

so tilting a board until a block just starts to move measures \(\mu_s\). Once sliding, the net force down the slope is \(mg\sin\theta - \mu_k mg\cos\theta\), giving

a = g(\sin\theta - \mu_k\cos\theta)

The mass cancels, so heavy and light blocks of the same material slide down together.

Worked example: a box on a ramp

A box is placed on a 30.0° ramp where \(\mu_s = 0.40\) and \(\mu_k = 0.20\). Does it slide, and if so, with what acceleration? 1. Test for slipping: \(\tan 30.0^\circ = 0.577\), which is greater than \(\mu_s = 0.40\), so static friction cannot hold it and it slides. 2. Acceleration: \(a = 9.80(\sin 30.0^\circ - 0.20\cos 30.0^\circ)\). 3. Substitute: \(a = 9.80(0.500 - 0.173) = 3.20\) m/s² down the ramp. 4. Check: without friction it would be \(g\sin 30.0^\circ = 4.90\) m/s², so friction has reduced it, as expected, and no mass was needed.

Worked example: braking on dry and wet roads

A car travels at 25.0 m/s on a level road. Find its stopping distance with the wheels locked and skidding, on dry and on wet concrete. 1. When the tyres skid, friction is kinetic: \(f_k = \mu_k mg\), so the deceleration is \(\mu_k g\) whatever the car's mass. 2. Dry, \(\mu_k \approx 0.8\): \(a = 7.84\) m/s². 3. Kinematics with \(v = 0\): \(d = \frac{v_0^2}{2a} = \frac{625}{15.68} = 39.9\) m, about 40 m. 4. Wet, \(\mu_k \approx 0.5\): \(a = 4.90\) m/s² and \(d = 63.8\) m, about 64 m. Anti-lock brakes stop the wheels locking, so each tyre's contact patch stays momentarily at rest on the road. The friction then stays static, which can be larger than kinetic friction, and the driver can still steer.

Common mistakes to avoid

First, writing \(f_s = \mu_s F_N\) for every object at rest: that is only the maximum, and the actual static friction matches whatever it must. Second, assuming \(F_N = mg\): on a slope \(F_N = mg\cos\theta\), and an angled push or pull changes it too. Third, thinking friction always opposes motion. It opposes relative sliding, so when you start to walk, the floor's static friction on your pushing-off shoe points forwards; it is the force that speeds you up. Fourth, using \(\mu_s\) for an object that is already sliding. Fifth, thinking a wider tyre or box face changes the friction; in the simple model it does not.

Key takeaways

Friction acts along the surface and opposes relative motion or attempted motion. Static friction adjusts to the need, up to a maximum: f_s ≤ μ_s F_N, with equality only at the point of slipping. Kinetic friction is f_k = μ_k F_N, and usually μ_k < μ_s, so starting an object takes more force than keeping it moving. The coefficients have no units and come from approximate measured tables. Find F_N from the free-body diagram rather than assuming mg. On a slope, slipping begins when tan θ = μ_s, and a sliding block accelerates at g(sin θ − μ_k cos θ). A skidding car decelerates at about μ_k g.

Flashcards

Flashcard

Friction

A contact force along a surface that opposes relative motion or attempted motion

It acts at right angles to the normal force.

Test your understanding

Question 1 of 5

A 25.0 kg box rests on a level floor with μ_s = 0.50 and μ_k = 0.30. You push it horizontally with 80.0 N. What is the friction force on the box? Use g = 9.80 m/s².

Question 2 of 5

A 10.0 kg box slides across a level floor (μ_s = 0.40, μ_k = 0.25) under a horizontal 60.0 N push. What is its acceleration? Use g = 9.80 m/s².

Question 3 of 5

A block rests on a board with μ_s = 0.60 between them. You slowly tilt the board. At about what angle does the block start to slip?

Question 4 of 5

A 3.0 kg block on a table (μ_k = 0.20) is pulled by a string over a light, frictionless pulley attached to a hanging 2.0 kg mass, and the block slides. What is the acceleration? Use g = 9.80 m/s².

Question 5 of 5

You start to walk forwards from standing still on a dry floor. What is the friction force of the floor on the shoe that pushes off?

← Previous topicNext topic →