Physics › Section O · Current and circuits › Topic O.6

Emf and terminal voltage

Turn the key in an old car with the headlights on and the lights dim as the starter motor turns. The battery has not changed; its output voltage has. Emf and internal resistance explain why a real source gives less voltage the more current you take from it.

What a source does

A resistor converts electrical energy into other forms; a source does the reverse, raising the potential energy of charge so that it can flow round the circuit again. A battery does this with chemical reactions, a generator with motion in a magnetic field, a solar cell with light. The electromotive force, or emf, written \(\mathcal{E}\), is the energy the source supplies to each coulomb of charge that passes through it:

\mathcal{E} = \frac{W}{q}

Despite its old name, emf is not a force. It is measured in volts, and it equals the potential difference across the source's terminals when no current flows.

Internal resistance

Charge passing through a real source meets resistance inside it: in a battery, the electrolyte and electrodes. We model a real source as an ideal emf \(\mathcal{E}\) in series with a small internal resistance \(r\). When a current \(I\) flows, part of the emf is lost as an \(Ir\) drop inside, so the potential difference across the terminals, the terminal voltage, is

V = \mathcal{E} - Ir

With no current, \(V = \mathcal{E}\). The more current is drawn, the lower the terminal voltage. Internal resistance also turns energy into heat inside the source at the rate \(I^2r\), which is why batteries warm up when they deliver a large current.

Worked example: starting a car

A car battery has emf 12.6 V and internal resistance 0.0150 Ω. Find its terminal voltage when the starter motor draws 200 A, and when only the headlights draw 10.0 A. 1. Starter:

V = \mathcal{E} - Ir = 12.6 - (200)(0.0150) = 9.60\ \mathrm{V}

2. Headlights alone: \(V = 12.6 - (10.0)(0.0150) = 12.45\) V, about 12.5 V. 3. Heating inside during starting: \(I^2r = 200^2 \times 0.0150 = 600\) W. 4. Check: the lamps are in parallel with the starter, so they get the terminal voltage; it falls from about 12.5 V to 9.60 V, and since lamp power goes roughly with \(V^2\), they dim noticeably. That is the effect in the opening paragraph.

Current from a real source

Connect a load resistance \(R\) to a source with emf \(\mathcal{E}\) and internal resistance \(r\). The two resistances are in series, so

I = \frac{\mathcal{E}}{R + r}

When \(R\) is much larger than \(r\), almost all the emf appears across the load and the source behaves nearly ideally. When \(R\) is small, \(r\) matters a lot. In the extreme of a short circuit, \(R \approx 0\), the current is limited only by the internal resistance, \(I = \mathcal{E}/r\), and the terminal voltage falls to almost zero. That is why shorting a battery is dangerous: all its energy is released as heat inside it and in the short.

Worked example: a fresh and a tired cell

A fresh AA cell has emf 1.50 V and internal resistance 0.200 Ω and runs a 2.80 Ω load. Find the current, terminal voltage and power to the load. Then repeat for an old cell whose internal resistance has risen to 2.00 Ω. 1. Fresh: \(I = 1.50/(2.80 + 0.200) = 0.500\) A, \(V = IR = 0.500 \times 2.80 = 1.40\) V, and \(P = I^2R = 0.700\) W. 2. Old: \(I = 1.50/(2.80 + 2.00) = 0.3125\) A, so \(V = 0.875\) V and \(P = 0.273\) W. 3. Check: \(\mathcal{E} - Ir\) gives \(1.50 - 0.100 = 1.40\) V and \(1.50 - 0.625 = 0.875\) V. The emf barely changes as a cell ages; its rising internal resistance is what starves the load.

Charging a battery

A rechargeable battery is charged by forcing current into its positive terminal, against its emf. Now the current runs backwards through the internal resistance, and the charger must supply both the emf and the internal drop:

V = \mathcal{E} + Ir

A charger pushing 2.00 A into a 12.0 V battery with \(r = 0.10\ \Omega\) must hold the terminals at \(12.0 + 0.20 = 12.2\) V. Of the 24.4 W it delivers, 24.0 W is stored as chemical energy and 0.40 W heats the battery. Whether you add or subtract \(Ir\) depends only on which way the current flows through the source.

Combining sources

Cells in series with the same orientation, positive to negative, add their emfs and their internal resistances: four 1.50 V cells in a torch give 6.00 V, and four 0.200 Ω internal resistances give 0.800 Ω. A cell put in backwards subtracts its emf. Identical cells in parallel keep the same emf but share the current, which lowers the effective internal resistance and lets the bank supply more current for longer. Solar panels use both ideas: each silicon cell gives only about 0.5 V, so a common panel has 36 cells in series for about 18 V, and panels are joined in parallel for more current. An electric eel works the same way, stacking thousands of cells called electrocytes in series to discharge several hundred volts.

Measuring an emf

A voltmeter across a battery reads its terminal voltage, \(\mathcal{E} - Ir\). A good digital voltmeter draws so little current that the reading is very close to the emf, but never exactly equal, because some current must flow through the meter. If you measure the terminal voltage at two known currents, you can find both quantities. For example, 6.0 V with no load and 5.4 V while 1.5 A flows means the internal drop is 0.6 V, so \(r = 0.6/1.5 = 0.40\ \Omega\). A later topic shows how a null measurement can find an emf with no current at all.

Common mistakes to avoid

First, treating emf as a force; it is energy per unit charge, in volts. Second, assuming the terminal voltage always equals the emf; it does only when no current flows. Third, using \(\mathcal{E} - Ir\) for a battery being charged, where the current is reversed and \(V = \mathcal{E} + Ir\). Fourth, forgetting to include \(r\) in series with the load when finding the current. Fifth, finding \(r\) by dividing the terminal voltage by the current; that gives the load resistance, not the internal resistance.

Key takeaways

Emf is the energy a source supplies per coulomb, ε = W/q, in volts, and equals the terminal voltage when no current flows. A real source is an ideal emf in series with an internal resistance r. Delivering current I, the terminal voltage is V = ε − Ir; being charged, V = ε + Ir. With a load R, I = ε/(R + r), and a short circuit gives I = ε/r. Large currents make the terminal voltage sag, and ageing cells fail mainly because r rises. Series cells add emfs and internal resistances.

Flashcards

Flashcard

Emf, ε

Energy supplied per unit charge by a source: ε = W/q

In volts; not a force.

Test your understanding

Question 1 of 5

A battery of emf 9.00 V and internal resistance 0.500 Ω is connected to a 4.00 Ω load. What is the terminal voltage?

Question 2 of 5

A battery reads 6.0 V with no load and 5.4 V while delivering 1.5 A. What is its internal resistance?

Question 3 of 5

A 1.50 V cell has an internal resistance of 0.25 Ω. What current flows if its terminals are shorted by a wire of negligible resistance?

Question 4 of 5

A charger pushes 4.00 A into a 12.0 V battery whose internal resistance is 0.0500 Ω. What terminal voltage must the charger maintain?

Question 5 of 5

Why do a car's headlights dim while the starter motor is running?

← Previous topicNext topic →