Physics › Section O · Current and circuits › Topic O.7

Kirchhoff's rules

Some circuits cannot be untangled into series and parallel pieces, especially when they contain more than one source. Kirchhoff's two rules, built on conservation of charge and of energy, solve any of them.

When series and parallel are not enough

Picture two batteries in different branches of a network, both feeding a shared resistor in the middle. No resistor in that circuit is purely in series or purely in parallel with another, so the step-by-step reduction of the previous topic fails. In 1845, while still a student, the German physicist Gustav Kirchhoff stated two rules that work for every circuit, however tangled. Each rule turns a piece of the circuit diagram into an equation. With as many independent equations as unknown currents, ordinary algebra finishes the job. The series and parallel formulas turn out to be special cases of these rules.

The junction rule

A junction is a point where three or more wires meet. Charge is conserved and cannot pile up at a junction in a steady circuit, so whatever flows in must flow out:

\sum I_{\text{in}} = \sum I_{\text{out}}

If 5.0 A and 3.0 A flow into a junction and one wire carries 6.0 A out, the remaining wire must carry 2.0 A out. In a circuit with \(n\) junctions, only \(n - 1\) of the junction equations are independent; the last one repeats information already contained in the others. The parallel-resistor rule, that branch currents add to the total, is this rule applied to one junction.

The loop rule

Around any closed loop in a circuit, the changes in potential add to zero:

\sum \Delta V = 0

This is conservation of energy. A charge that travels round a loop and returns to its starting point is back at the same potential, so whatever energy sources gave it was handed over to the resistors or to batteries being charged. Think of a roller coaster: the lift hill, like an emf, raises the cars, and the drops, like resistors, bring them back to the starting height. For a single battery driving a series chain, the loop rule says the emf equals the sum of the \(IR\) drops, which is the series rule you already know.

Sign conventions

Signs are where most errors happen, so fix the convention first. Choose a direction for each unknown current and mark it on the diagram. Then choose a direction to travel round each loop. As you cross each element in your direction of travel: a resistor crossed in the same direction as its assumed current contributes \(-IR\), because current flows downhill in potential; a resistor crossed against its current contributes \(+IR\); an emf crossed from its negative to its positive terminal contributes \(+\mathcal{E}\); an emf crossed from positive to negative contributes \(-\mathcal{E}\). The assumed current directions need not be right: a current that comes out negative simply flows the other way, with the same size.

A method that always works

1. Draw the circuit, label every resistance and emf, and give each branch a current with an assumed direction. A branch is a stretch between junctions, with one current throughout. 2. Write the junction rule at junctions until each current has appeared. 3. Write the loop rule for enough independent loops to have as many equations as unknown currents. A loop that adds no new branch gives a redundant equation. 4. Solve the simultaneous equations. 5. Check: substitute into an equation you did not use, such as a loop round the outside, and confirm that the power supplied by the sources equals the power dissipated.

Worked example: two batteries in one loop

A 12.0 V battery and a 4.0 V battery are in one loop with a 3.0 Ω and a 5.0 Ω resistor, connected so that the batteries oppose each other. Ignore internal resistance. 1. Assume the current \(I\) flows clockwise, the way the 12.0 V battery pushes it, and travel clockwise. 2. Loop rule, crossing the 12.0 V battery from − to + and the 4.0 V battery from + to −:

12.0 - 3.0I - 4.0 - 5.0I = 0

3. Solve: \(8.0I = 8.0\), so \(I = 1.0\) A, positive, so clockwise as assumed. 4. Check: the drops are 3.0 V and 5.0 V, and \(12.0 - 4.0 = 8.0\) V. The larger battery is charging the smaller one.

Worked example: a two-loop circuit

Three branches join junction a at the top to junction b at the bottom. The left branch has a 12.0 V battery and \(R_1 = 2.0\ \Omega\), the right branch a 6.0 V battery and \(R_2 = 4.0\ \Omega\), both with positive terminals towards a. The middle branch is \(R_3 = 4.0\ \Omega\). Assume \(I_1\) and \(I_2\) flow up the outer branches and \(I_3\) down the middle. 1. Junction a: \(I_1 + I_2 = I_3\). 2. Left loop, up the left and down the middle: \(12.0 - 2.0I_1 - 4.0I_3 = 0\). 3. Right loop, up the right and down the middle: \(6.0 - 4.0I_2 - 4.0I_3 = 0\). 4. From these, \(I_1 = 6.0 - 2.0I_3\) and \(I_2 = 1.5 - I_3\). Substituting into step 1 gives \(7.5 = 4.0I_3\), so \(I_3 = 1.875\) A.

Interpreting and checking the answer

Back-substituting gives \(I_1 = 6.0 - 3.75 = 2.25\) A and \(I_2 = 1.5 - 1.875 = -0.375\) A. The minus sign means \(I_2\) actually flows down through the right branch, into the positive terminal of the 6.0 V battery, so that battery is being charged. Now check. The outer loop, up the left and down the right, gives

12.0 - 2.0(2.25) + 4.0(-0.375) - 6.0 = 0

as it should. The 12.0 V battery supplies \(12.0 \times 2.25 = 27.0\) W. The 6.0 V battery absorbs \(6.0 \times 0.375 = 2.25\) W, and the resistors dissipate

10.125 + 0.5625 + 14.0625 = 24.75\ \mathrm{W}

Since \(27.0 - 2.25 = 24.75\), energy balances.

Common mistakes to avoid

First, mixing sign conventions part way round a loop; decide the direction of travel and apply the four rules to every element. Second, giving an emf a sign based on the current direction; its sign depends only on whether you cross it from − to + or from + to −. Third, writing more junction equations than are independent and too few loop equations. Fourth, changing an assumed current direction after a negative result instead of simply reading the sign. Fifth, using a different current in two parts of the same branch.

Key takeaways

Kirchhoff's junction rule, ΣI in = ΣI out, comes from conservation of charge. His loop rule, ΣΔV = 0 around any closed loop, comes from conservation of energy. Sign convention: a resistor crossed with its current gives −IR, against it +IR; an emf crossed from − to + gives +ε, from + to − gives −ε. Assume current directions freely; a negative answer means the current flows the other way. You need as many independent equations as unknowns. Check with an unused loop and with a power balance.

Flashcards

Flashcard

Junction

A point where three or more wires meet

Branches run between junctions.

Test your understanding

Question 1 of 5

Currents of 5.0 A and 2.0 A flow into a junction, and 4.0 A flows out along a third wire. What is the current in the fourth wire?

Question 2 of 5

Going round a loop, you cross a 4.0 Ω resistor in the direction opposite to its 2.0 A current. What potential change do you record?

Question 3 of 5

A 15.0 V battery and a 6.0 V battery are connected in a single loop so that they oppose each other, with a total resistance of 3.0 Ω and no internal resistance. What current flows?

Question 4 of 5

Solving a circuit with Kirchhoff's rules gives I₂ = −0.60 A. What does this mean?

Question 5 of 5

Three branches join junction a to junction b. Branch 1 has an 18.0 V battery and a 6.0 Ω resistor; branch 2 has a 12.0 V battery and a 3.0 Ω resistor; both batteries have their positive terminals towards a. Branch 3 is a single 6.0 Ω resistor. What current flows in branch 3?

← Previous topicNext topic →