Physics › Section Q · Electromagnetic induction and AC circuits › Topic Q.3

Generators and back emf

Most of the world's electricity comes from coils turning in magnetic fields. The same physics runs backwards inside every electric motor, where a self-induced emf limits the current and explains why motors draw so much more current as they start.

Turning motion into electricity

A power station, a wind turbine and a hydroelectric dam all end in the same machine: a generator. Steam, wind or falling water spins a turbine, and the turbine turns a coil in a magnetic field, or a magnet inside fixed coils. Either way the flux through the coils keeps changing, so Faraday's law guarantees an emf. A generator converts mechanical work into electrical energy; it does not create energy. This topic finds the emf a turning coil produces, then shows that an electric motor, which is built the same way, generates an emf of its own while it runs.

A coil turning in a field

Take a flat coil of \(N\) turns and area \(A\) turning at a steady angular velocity \(\omega\), in radians per second, in a uniform field \(B\). If the coil's normal points along the field at \(t = 0\), the angle between them is \(\theta = \omega t\), and the flux through each turn is \(BA\cos\omega t\). The flux is largest when the coil faces the field, but at that moment it is not changing, so the emf is zero. The emf is largest a quarter turn later, when the coil's plane lies along the field: the flux is momentarily zero but changing fastest. As in earlier topics, \(\omega = 2\pi f\), where \(f\) is the number of turns per second.

The generator equation

Motional emf gives the result without calculus. Let the coil be a rectangle whose two long sides, of length \(l\), sit a distance \(w/2\) from the axis, so each moves at \(v = \omega w/2\). Only the part of that velocity across the field, \(v\sin\omega t\), induces an emf, so each long side gives \(Blv\sin\omega t\). The two sides add, and \(lw = A\), so each turn gives \(BA\omega\sin\omega t\). For \(N\) turns:

\mathcal{E} = NAB\omega\sin\omega t

The emf alternates as a sine wave of frequency \(f\), with peak value \(\mathcal{E}_0 = NAB\omega\). Turning faster raises both the peak and the frequency.

Worked example: a 60 Hz generator

A generator coil has 150 turns, each 0.120 m by 0.0800 m, and turns at 60.0 revolutions per second in a uniform 0.400 T field. Find its peak emf, its rms emf, and its emf 2.00 ms after the coil faces the field. 1. Area and angular velocity: \(A = 9.60 \times 10^{-3}\ \text{m}^2\) and \(\omega = 2\pi(60.0) = 377\) rad/s. 2. Peak emf:

\mathcal{E}_0 = NAB\omega = (150)(9.60 \times 10^{-3})(0.400)(377) = 217\ \text{V}

3. rms value: \(217/\sqrt{2}\), which is 154 V. 4. At 2.00 ms, \(\omega t = 0.754\) rad, and \(\sin 0.754 = 0.685\), so \(\mathcal{E} = 217 \times 0.685 = 149\) V. 5. Check: 2.00 ms is less than a quarter of the 16.7 ms period, so the emf is still climbing towards its peak, as found.

Real generators

To take current out of a spinning coil, each end of the coil connects to a slip ring, a metal ring on the shaft, and carbon brushes press on the rings. The output is AC. Replace the two rings with a single split ring, a commutator, which swaps the connections every half turn, and the output becomes pulsing DC that never reverses. Large power-station generators turn the arrangement inside out: an electromagnet spins inside fixed coils, so the high-current output needs no sliding contacts. A simple two-pole machine on the US 60 Hz grid turns 60 times a second, 3600 revolutions per minute, and most use three sets of coils to deliver three-phase power.

Why a loaded generator is hard to turn

Spin a generator with nothing connected and it turns easily, because no current flows. Connect a lamp and current flows in the coil. That current sits in a magnetic field, so it feels a force, and by Lenz's law the resulting torque opposes the rotation. The more electrical power drawn, the larger the current and the harder the turbine must push. This is energy conservation at work: every joule delivered to the lamp is a joule of work done on the shaft. A hand-cranked torch gets noticeably harder to crank when its lamp is switched on.

Back emf in motors

An electric motor is a generator in reverse: current in a coil in a magnetic field produces a torque that turns it. But a turning coil in a field also generates an emf. By Lenz's law this emf opposes the applied voltage, so it is called the back emf. If the supply is \(V\), the coil resistance \(R\) and the back emf \(\mathcal{E}_b\), the current is

I = \frac{V - \mathcal{E}_b}{R}

At switch-on the coil is still, the back emf is zero, and the current is large. As the motor speeds up the back emf grows, and the current falls. A heavier load slows the motor, lowers the back emf, and so draws more current.

Worked example: a motor starting and running

A 12.0 V DC motor has coil resistance 0.800 Ω. At full speed its back emf is 10.4 V. Find the current at start-up and at full speed, and how the running power divides. 1. At start-up the back emf is zero: \(I = 12.0/0.800 = 15.0\) A. 2. At full speed:

I = \frac{12.0 - 10.4}{0.800} = 2.00\ \text{A}

3. Power from the supply: \(VI = 24.0\) W. 4. Heat in the coil: \(I^2R = 3.20\) W. 5. The rest, \(\mathcal{E}_bI = 10.4 \times 2.00 = 20.8\) W, becomes mechanical work. 6. Check: 20.8 + 3.20 = 24.0 W. The starting current is 7.5 times the running current.

Back emf in everyday life

Lights in a house sometimes dim for a moment when a refrigerator or air conditioner starts, because the motor draws its large starting current through the shared wiring. A motor that jams, or is overloaded until it stalls, has no back emf, so it keeps drawing its full starting current, and the coil can overheat and burn out. Circuit breakers on motor circuits are chosen to tolerate the short starting surge without tripping. The fraction of the input power turned into work, \(\mathcal{E}_bI/VI = \mathcal{E}_b/V\), also shows why a motor running fast and lightly loaded wastes little energy as heat.

Common mistakes to avoid

First, putting the frequency \(f\) into \(NAB\omega\) instead of \(\omega = 2\pi f\). Second, thinking the emf is largest when the flux is largest; it is largest when the flux is zero and changing fastest. Third, forgetting \(N\), or quoting the peak emf when an rms value is asked for. Fourth, using \(I = V/R\) for a running motor; the back emf must be subtracted first. Fifth, believing back emf adds to the supply; it always opposes it.

Key takeaways

A generator turns a coil in a magnetic field, or a magnet inside coils, converting mechanical work into electrical energy. For N turns of area A at angular velocity ω in a field B, emf = NABω sin ωt, with peak NABω and ω = 2πf. The emf is zero when the coil faces the field and largest when its plane lies along it. Slip rings give AC; a commutator gives pulsing DC. Drawing current makes a generator harder to turn. A running motor generates a back emf, so I = (V − back emf)/R: large at start-up and when stalled, small at full speed.

Flashcards

Flashcard

Generator

Turns a coil in a magnetic field to convert mechanical work into electrical energy

Or spins a magnet inside fixed coils.

Test your understanding

Question 1 of 5

A generator coil of 100 turns, each of area 0.0200 m², turns 20.0 times a second in a uniform 0.250 T field. What is its peak emf?

Question 2 of 5

At which position of a turning generator coil is the induced emf largest?

Question 3 of 5

A 24.0 V motor with coil resistance 2.00 Ω runs with a back emf of 20.0 V. What current does it draw?

Question 4 of 5

A running motor jams and stops turning while still connected. What happens to its current?

Question 5 of 5

A generator's rotation rate is doubled. What happens to the peak emf and the frequency of its output?

← Previous topicNext topic →