Physics › Section Q · Electromagnetic induction and AC circuits › Topic Q.2
Motional emf and eddy currents
Move a conductor through a magnetic field and an emf appears in it, even though the field itself never changes. The same effect swirls currents through solid metal, and those currents brake roller coasters, sort scrap and heat pans.
Moving wires, steady fields
The previous topic changed the flux through a fixed loop. A conductor moving through a steady field does the same job. Picture two parallel metal rails joined at one end by a resistor, in a uniform field perpendicular to the rails' plane, with a metal rod lying across them. As the rod slides, the loop of rails, rod and resistor grows, the flux through it increases, and a current flows. This is motional emf. Two explanations always agree: the change in flux, or the magnetic force on the charges carried along inside the rod.
The flux view: emf = Blv
Let the rod have length \(l\) between the rails and slide at speed \(v\), with \(B\), \(l\) and \(v\) mutually perpendicular. In a time \(\Delta t\) the rod moves \(v\Delta t\), so the loop's area grows by \(lv\Delta t\) and the flux by \(Blv\Delta t\). Faraday's law with one turn then gives the size of the emf:
Doubling the field, the rod's length or its speed doubles the emf. If the motion is not perpendicular to the field, only the perpendicular part of the velocity counts, and a rod moving along the field lines has no emf at all.
The force view
Each free charge \(q\) in the rod moves with the rod at speed \(v\), so it feels a magnetic force \(qvB\) directed along the rod, by the right-hand rule for moving charges. Charges are pushed towards one end, leaving the other end with the opposite charge. They pile up until the electric field \(E\) they create balances the magnetic push, \(qE = qvB\), so \(E = vB\). Across the length \(l\) that is a potential difference \(El = Blv\), the same result as before. The moving rod behaves like a battery: it has an emf even with no rails attached, though a current flows only once a complete circuit exists.
Worked example: a rod on rails
The field of 0.600 T points into the page, the rails run left to right with a 1.50 Ω resistor joining them at the left end, and a rod 0.250 m long slides right at a steady 4.00 m/s. Ignore friction and the resistance of the rod and rails. 1. Emf:
2. Current: \(I = 0.600/1.50 = 0.400\) A. 3. Direction: the flux into the page is increasing, so the induced field points out of the page inside the loop, and the current runs anticlockwise as seen, up the page through the rod. 4. The force on the rod, \(IlB = 0.0600\) N, points left by the right-hand rule, against the motion. 5. Check energy: pushing takes \(Fv = 0.240\) W, and the resistor dissipates \(I^2R = 0.240\) W.
Worked example: an aircraft's wings
An airliner with a wingspan of 35.0 m flies level at 250 m/s where the vertical part of Earth's field is \(4.50 \times 10^{-5}\) T. What emf appears between the wingtips? 1. Only the vertical part of the field matters, because the wings and velocity are horizontal and at right angles. 2.
3. Check the size: Earth's field is weak, so even a long, fast conductor gives well under a volt. 4. This emf cannot run anything on board. Any wire connecting the wingtips moves with the plane and has the same emf induced in it, so the two cancel around the loop and no current flows.
Eddy currents
Motional emf does not need a wire. When a solid piece of metal moves through a non-uniform field, or sits in a changing one, emfs drive loops of current through the metal itself. These swirling loops are eddy currents. By Lenz's law, the forces on them oppose the motion, an effect called magnetic damping. A copper or aluminium pendulum plate swinging between the poles of a strong magnet stops within a few swings, slowed on the way into the field and again on the way out. While the plate is wholly inside a uniform field its flux does not change, so there is no eddy current and no drag. A plastic plate is not slowed, because almost no current can flow.
Drag that depends on speed
The induced emf is proportional to speed, so the eddy currents are too, and so is the magnetic force on them. Magnetic drag therefore grows with speed and falls to zero when the motion stops. The kinetic energy removed becomes heat in the metal. Cutting slots in the pendulum plate breaks up the large current loops, so the eddies and the drag become much smaller and the plate swings freely. Engineers use the same trick in reverse: transformer and motor cores are built from thin insulated sheets, called laminations, to keep wasteful eddy currents and the heating they cause small.
Worked example: magnetic brakes on a ride
Copper fins on a 1500 kg ride car pass between rows of strong magnets. Model the braking force as \(F = bv\), with b = 600 N·s/m, and ignore friction. Find the deceleration at 24.0 m/s and at 6.00 m/s. 1. At 24.0 m/s: \(F = 600 \times 24.0\), which is 14,400 N. 2. Newton's second law:
about one g. 3. At 6.00 m/s: \(F = 3600\) N, so \(a = 2.40\ \text{m/s}^2\). 4. Check: a quarter of the speed gives a quarter of the force. The braking fades as the car slows, so a ride also needs friction brakes to stop the car fully and hold it.
Eddy currents at work
Magnetic brakes on trains and rides never touch the track, so they do not wear and work the same in rain. Sensitive balances use a conducting vane moving past a magnet to stop their swinging; the drag vanishes once the pointer is still, so the reading is unaffected. At recycling plants, a fast-spinning magnet drum induces eddy currents that fling aluminium and other non-iron metals off a belt, while plastics and glass fall off normally. Induction hobs drive a rapidly changing field into the base of a pan, and the eddy currents heat the pan directly; most need a pan with an iron or steel base. Metal detectors sense the eddy currents induced in hidden metal.
Common mistakes to avoid
First, using \(Blv\) when the velocity is not perpendicular to the field; only the perpendicular part of the velocity counts. Second, getting the force on the rod in the same direction as the motion; Lenz's law always makes it oppose the motion, which is why energy balances. Third, expecting eddy current drag while a plate sits inside a uniform field; the flux must change. Fourth, thinking magnetic brakes need iron; any conductor works, including copper and aluminium. Fifth, expecting magnetic brakes to hold a vehicle at rest; the drag is zero at zero speed.
Key takeaways
A conductor moving through a magnetic field has an emf induced in it: emf = Blv when B, l and v are mutually perpendicular. It can be explained by the flux swept out or by the magnetic force on charges in the conductor. Lenz's law makes the force on the induced current oppose the motion, and the work done against it becomes electrical energy. Eddy currents are induced loops of current in bulk metal; they cause magnetic damping proportional to speed, and they are reduced by slots and laminations. They are used in brakes, balances, recycling, induction hobs and metal detectors.
Flashcards
Flashcard
The emf induced in a conductor moving through a magnetic field
Test your understanding
Question 1 of 5
A rod 0.40 m long moves at 3.0 m/s at right angles to a uniform 0.50 T field, perpendicular to its own length. What emf is induced across it?
Question 2 of 5
That rod, with an emf of 0.60 V, now slides on rails joined by a 2.0 Ω resistor in the same 0.50 T field. What magnetic force acts on the 0.40 m rod?
Question 3 of 5
A copper plate on a pendulum swings into, through and out of the uniform field between two magnet poles. How do eddy currents affect it?
Question 4 of 5
A magnetic brake exerts 8000 N on a car moving at 20 m/s. Assuming the force is proportional to speed, what does it exert at 5.0 m/s?
Question 5 of 5
A slotted aluminium plate swings between magnet poles far longer than a solid one. Why?
