Physics › Section O · Current and circuits › Topic O.8

Voltmeters, ammeters, and null measurements

Every measurement of a circuit slightly changes the circuit being measured. Knowing how meters are built and connected tells you how big that change is, and null methods show how to make it vanish.

Measuring changes what you measure

To measure a current you must send it through a meter; to measure a voltage you must give some charge a path through a meter. Either way the meter becomes part of the circuit and alters the very current or voltage it reports. A good meter keeps that disturbance small, and knowing which way the error goes lets you judge a reading. This topic shows how the two standard meters are connected, how a sensitive basic meter is adapted into each, and how null measurements avoid drawing current altogether. The circuits use the series, parallel and emf ideas of the previous topics.

Ammeters and voltmeters

An ammeter measures current, so the current must pass through it: it is connected in series, by breaking the circuit and inserting the meter. To avoid reducing the current it should have a very small resistance. A voltmeter measures the potential difference between two points, so it is connected in parallel, across the component, without breaking the circuit. To avoid drawing current away from the component it should have a very large resistance; a typical digital multimeter has an input resistance of about 10 MΩ on its voltage ranges. Connecting an ammeter in parallel is a classic error: its tiny resistance acts almost as a short circuit and can blow the meter's fuse.

The galvanometer

Traditional analogue meters are built round a galvanometer: a coil of wire on a pivot between magnet poles, with a needle attached. Current through the coil makes it turn against a spring, so the deflection is proportional to the current; a later topic on magnetism explains the turning. A galvanometer is very sensitive. Typical values are a full-scale current \(I_G = 50.0\ \mu\mathrm{A}\) and a coil resistance \(r_G = 25.0\ \Omega\), so it reaches full scale with only \(I_Gr_G = 1.25\) mV across it. On its own it can measure only tiny currents and voltages, so extra resistors are added to make practical meters.

Worked example: building a voltmeter

Convert the galvanometer above into a voltmeter that reads 20.0 V at full scale. A large resistance \(R\) is placed in series with the coil, so that 20.0 V across the combination drives exactly \(I_G\). 1. Total resistance needed:

R + r_G = \frac{V}{I_G} = \frac{20.0}{50.0 \times 10^{-6}} = 4.00 \times 10^5\ \Omega

2. Series resistance:

R = 4.00 \times 10^5 - 25.0 = 399{,}975\ \Omega

about 400 kΩ. 3. Check: at full scale, \(50.0\ \mu\mathrm{A} \times 400\ \mathrm{k\Omega} = 20.0\) V. The whole meter has a resistance of 400 kΩ, large compared with most circuit resistors, as a voltmeter's should be.

Worked example: building an ammeter

Now make the same galvanometer read 2.00 A at full scale. A small shunt resistance \(R_s\) is connected in parallel with the coil so that most of the current bypasses it. 1. At full scale the coil carries \(I_G = 50.0\ \mu\)A, so the shunt carries \(2.00 - 0.00005 = 1.99995\) A. 2. The coil and shunt are in parallel, so they have the same voltage: \(I_Gr_G = (I - I_G)R_s\). 3. Solve:

R_s = \frac{(50.0 \times 10^{-6})(25.0)}{1.99995} = 6.25 \times 10^{-4}\ \Omega

4. Check: the meter's total resistance is less than the shunt alone, well under a milliohm, so inserting it in series barely changes the circuit's current.

Worked example: a voltmeter that loads the circuit

Two 100 kΩ resistors are in series across an ideal 10.0 V source, so each should have 5.00 V. A voltmeter of resistance 1.00 MΩ is connected across one of them. What does it read? 1. The meter and the resistor are in parallel:

R_p = \frac{(1.00 \times 10^5)(1.00 \times 10^6)}{1.10 \times 10^6} = 90.9\ \mathrm{k\Omega}

2. Voltage divides in proportion to resistance:

V = 10.0 \times \frac{90.9}{90.9 + 100} = 4.76\ \mathrm{V}

3. A 10.0 MΩ meter would read 4.98 V instead. 4. Check: the reading is low, as expected, because adding a parallel path always lowers the resistance it is connected across. A voltmeter is accurate only when its resistance is far larger than what it measures.

The idea of a null measurement

Ordinary meters must draw or carry some current, so they always disturb the circuit a little. A null measurement avoids this by balancing two potential differences against each other and adjusting until a sensitive detector, such as a galvanometer, shows zero current. At balance no current flows through the detector, so it has no effect on the circuit, and the detector need not even be accurately calibrated: it only has to show reliably when the current is zero. The result then depends only on precisely known resistances or emfs. The accuracy is limited by how closely zero can be judged and by the uncertainty in those reference values.

The potentiometer

A potentiometer measures an emf without drawing current from it. A steady current from a working battery flows along a long uniform wire, so the potential falls evenly along it and the voltage tapped off is proportional to the length used. The unknown cell is connected, through a galvanometer and opposing the wire's voltage, to a sliding contact, which is moved until the galvanometer reads zero. Then no current flows through the cell, so there is no \(Ir\) drop and its full emf is balanced. Repeating with a standard cell of known emf gives

\mathcal{E}_x = \mathcal{E}_s \frac{L_x}{L_s}

If a 1.500 V standard balances at 50.0 cm and the unknown at 62.0 cm, then \(\mathcal{E}_x = 1.86\) V.

Worked example: a Wheatstone bridge

A Wheatstone bridge measures an unknown resistance \(R_x\). Two branches are connected across a battery: one holds \(R_1\) and \(R_2\), the other \(R_3\) and \(R_x\), with \(R_1\) and \(R_3\) joined to the same terminal. A galvanometer bridges the midpoints. At balance the midpoints are at the same potential, so the resistance ratio is equal in both branches:

\frac{R_1}{R_2} = \frac{R_3}{R_x}, \qquad R_x = \frac{R_2R_3}{R_1}

With \(R_1 = 100.0\ \Omega\) and \(R_2 = 250.0\ \Omega\), balance occurs at \(R_3 = 182.4\ \Omega\). 1. Substitute:

R_x = \frac{(250.0)(182.4)}{100.0} = 456.0\ \Omega

2. Check the ratios: \(100.0/250.0 = 0.4000\) and \(182.4/456.0 = 0.4000\). Bridges inside strain gauges and digital scales sense tiny changes in resistance.

Common mistakes to avoid

First, connecting an ammeter in parallel or a voltmeter in series. Second, putting a voltmeter's extra resistor in parallel, or an ammeter's shunt in series. Third, forgetting the coil's own resistance when sizing the series resistor. Fourth, assuming a meter reading is exact; a voltmeter reads low when its resistance is not much larger than the component's. Fifth, inverting the bridge ratio; check that both branches give the same ratio at balance.

Key takeaways

An ammeter goes in series and should have very low resistance; a voltmeter goes in parallel and should have very high resistance. A galvanometer becomes a voltmeter with a large series resistor, R = V/I_G − r_G, and an ammeter with a small parallel shunt, R_s = I_G r_G/(I − I_G). Real meters slightly alter what they measure. Null measurements balance the circuit so no current flows through the detector: the potentiometer gives ε_x = ε_s L_x/L_s, and the Wheatstone bridge gives R_x = R₂R₃/R₁.

Flashcards

Flashcard

Ammeter

Measures current; connected in series

Needs a very low resistance.

Test your understanding

Question 1 of 5

How should an ammeter and a voltmeter be connected to measure the current through and voltage across a resistor?

Question 2 of 5

A galvanometer has a full-scale current of 100 μA and a coil resistance of 50.0 Ω. What must be added to make a 5.00 V full-scale voltmeter?

Question 3 of 5

Two 100 kΩ resistors are in series across an ideal 10.0 V source. A voltmeter of resistance 1.00 MΩ is connected across one of them. What does it read?

Question 4 of 5

A Wheatstone bridge has R₁ = 40.0 Ω and R₂ = 60.0 Ω in one branch, and balances when R₃ = 150 Ω, where R₁ and R₃ join the same battery terminal. What is the unknown resistance R_x?

Question 5 of 5

Why can a potentiometer measure the emf of a cell more accurately than a voltmeter connected across it?

← Previous topicNext topic →