Physics › Section G · Statics, torque, and rotation › Topic G.3
Simple machines and forces in the body
Crowbars, ramps and pulleys let a modest push move a heavy load, while your own muscles work the other way round, pulling far harder than the loads they lift. Both follow from the torque balance you have just learned.
What a machine does
A simple machine changes the size or direction of a force. You apply an input force \(F_i\), and the machine exerts an output force \(F_o\) on the load. Their ratio is the mechanical advantage:
An MA of 5 means the load receives five times your push. There is a price. A machine cannot put out more work than you put in, so if it multiplies force by 5, the load moves at most one fifth as far as your hands. Every simple machine makes this trade between force and distance.
The lever
A lever is a rigid bar that turns about a fixed pivot called the fulcrum. Treat it as massless and frictionless, with the input and output forces at lever arms \(l_i\) and \(l_o\) from the fulcrum. Holding the load steady means zero net torque about the fulcrum, \(F_i l_i = F_o l_o\), so
Levers come in three classes. In a first-class lever the fulcrum lies between effort and load, as in a crowbar or seesaw. In a second-class lever the load lies between, as in a wheelbarrow or nutcracker, so the MA is always above 1. In a third-class lever the effort lies between, as in tweezers or a fishing rod, so the MA is always below 1.
Worked example: shifting a rock
A gardener pushes down on a crowbar 1.20 m from its fulcrum, a stone under the bar. On the other side, 0.15 m from the fulcrum, the bar's tip is under a heavy rock, which presses down on it with 600 N. Treating the bar as light, what push is needed to lift the rock? 1. This is a first-class lever with \(l_i = 1.20\) m and \(l_o = 0.15\) m. 2. \(MA = \frac{1.20}{0.15} = 8.0\). 3. \(F_i = \frac{F_o}{MA} = \frac{600}{8.0} = 75\) N. 4. Check with torques: \(75 \times 1.20 = 90\) N m and \(600 \times 0.15 = 90\) N m. 5. The trade: to raise the rock 2.0 cm, the gardener's hands must move 8.0 times as far, 16 cm.
Wheels, axles and ramps
A wheel and axle, or a crank, is a lever that turns all the way round. With the input at radius \(R\) and the output at radius \(r\), \(MA = R/r\): a winch with a 0.30 m handle on a 0.050 m drum has an MA of 6.0. A car's axle drives a much larger wheel, so its MA is below 1, trading force for speed at the tyre. An inclined plane raises a load as you push it along a slope. For a frictionless ramp of length \(L\) and height \(h\), pushed parallel to the slope, \(MA = L/h\). Pushing a 1200 N crate up a ramp 3.0 m long and 0.50 m high takes 200 N, and both routes need 600 J of work.
Pulleys
A single fixed pulley gives no gain in force, MA = 1, but it redirects your effort, so pulling down lifts a load up. Combinations of pulleys, called a block and tackle, multiply force. If the pulleys are frictionless and light, and the rope segments are vertical, every segment holding up the moving block carries the same tension as the free end you pull. So the ideal MA equals the number of rope segments supporting the load. With 4 supporting segments, an 800 N load needs only 200 N, but you must pull 4 m of rope for every 1 m the load rises. Real pulleys have friction and weight, so the actual MA is always somewhat less than this ideal value.
Muscles as levers
Your skeleton is a set of levers, with joints as fulcrums and muscles providing the input force. Muscles can only pull, never push, so they work in pairs: in the upper arm the biceps bends the elbow and the triceps straightens it. Most muscles attach to bones through tendons close to a joint, while the load is far from it. That makes most limbs third-class levers with an MA well below 1, so muscle forces are many times larger than the loads in your hands. The benefit is speed and range: a muscle that shortens by a centimetre or two can swing the hand through a large arc in a fraction of a second.
Worked example: holding a shopping bag
A person holds a 3.0 kg bag with the forearm horizontal and the upper arm vertical. Use typical values, which vary from person to person: the biceps pulls straight up 5.0 cm from the elbow, the forearm and hand weigh 20 N with their cg 16 cm from the elbow, and the bag hangs 35 cm from the elbow. Find the biceps force. 1. Take torques about the elbow, so the joint force drops out. 2. Bag weight: \(3.0 \times 9.80 = 29.4\) N. 3.
4. \(F_b = \frac{13.49}{0.050} = 270\) N. 5. Check: the bag and forearm together weigh 49.4 N, so the biceps pulls about 5.5 times that combined weight, and about 9.2 times the bag's 29.4 N alone, as an MA well below 1 predicts.
Forces at the joint
The force balance finishes the forearm problem. Upwards there is the biceps pull, 270 N; downwards the two weights, 49.4 N, and the force from the upper-arm bone at the elbow, \(F_j\). Zero net force gives \(F_j = 270 - 49.4 = 220\) N downwards, also several times the load. Real joints are more complicated, since the pivot shifts and the lever arms change as a joint bends, but this model gives sensible sizes. It also explains back strain. Bend forward, and your upper body's weight acts far in front of the lower spine, while the back muscles act only a few centimetres behind it, so they pull very hard and squeeze the spinal discs. Lifting with a straight back, bending the knees and keeping the load close shrinks those lever arms.
Common mistakes to avoid
First, inverting the lever formula; the MA is the input lever arm over the output lever arm, so a long handle gives a large MA. Second, expecting a machine to save work; it trades force for distance, and with friction you put in more work than you get out. Third, counting every rope segment in a pulley system instead of only those holding up the moving block. Fourth, forgetting the forearm's own weight in a muscle problem. Fifth, assuming the joint force is small; it can be several times the load.
Key takeaways
Mechanical advantage is MA = Fo/Fi. A machine multiplies force only by reducing the distance moved, because work out cannot exceed work in. For an ideal lever, MA = li/lo from zero net torque about the fulcrum; second-class levers have MA above 1 and third-class levers below 1. A wheel and axle has MA = R/r, a frictionless ramp L/h, and a light, frictionless block and tackle has an ideal MA equal to the number of rope segments supporting the load. Most muscles attach near joints, so limbs are third-class levers: muscle and joint forces are several times the load, in exchange for speed and range of motion.
Flashcards
Flashcard
MA = output force ÷ input force
Test your understanding
Question 1 of 5
A light lever has the effort 0.90 m from the fulcrum and a 540 N load 0.10 m from it, on the other side. What effort holds the load steady?
Question 2 of 5
A light, frictionless block and tackle has 3 rope segments holding up the moving block. What pull lifts a 450 N load at steady speed?
Question 3 of 5
A forearm is horizontal with the biceps pulling straight up 4.0 cm from the elbow. Ignoring the forearm's own weight, what biceps force holds a 40 N ball 32 cm from the elbow?
Question 4 of 5
Why is it useful that most muscles attach close to the joints they move?
Question 5 of 5
A 600 N box is pushed up a frictionless ramp 4.0 m long and 0.80 m high, with the push parallel to the ramp. What push keeps it moving at steady speed?
