Physics › Section G · Statics, torque, and rotation › Topic G.2

Stability and applying statics

An object can be balanced and still fall over at the slightest nudge. The centre of gravity explains which balanced positions survive a push, and the two equilibrium conditions then let you find the forces in real structures such as brackets, beams and shelves.

Balanced is not the same as stable

A pencil lying on a desk and a pencil balanced on its point both meet the two conditions for equilibrium from the previous topic. Yet a breath of air topples the second, while the first stays put. Equilibrium says whether an object can stay where it is; stability says what happens when something disturbs it. Both depend on one special point, the centre of gravity.

The centre of gravity

For torque calculations an object's total weight can be treated as one force acting at a single point, the centre of gravity (cg). In uniform gravity, as over any everyday object, it is the same point as the centre of mass. For a uniform rod, block or disc it lies at the geometric centre. For separate pieces along a line, it is the mass-weighted average position:

x_{cg} = \frac{m_1x_1 + m_2x_2 + \cdots}{m_1 + m_2 + \cdots}

For a flat irregular shape, hang it from two different points and draw the vertical line below each; the lines cross at the cg. It need not lie inside the material: a ring's cg is at its empty centre.

Worked example: a loaded rod

A uniform 2.0 kg rod, 2.0 m long, has a 4.0 kg mass at its left end and a 2.0 kg mass at its right end. Where is the centre of gravity? 1. Measure from the left end: the 4.0 kg mass is at 0, the rod's cg at its midpoint, 1.0 m, and the 2.0 kg mass at 2.0 m. 2. Weighted average:

x_{cg} = \frac{4.0(0) + 2.0(1.0) + 2.0(2.0)}{8.0} = \frac{6.0}{8.0}

3. So \(x_{cg} = 0.75\) m from the left end. 4. Check by torques: a support at 0.75 m balances it, because \(4.0(0.75) = 3.0\) on the left equals \(2.0(0.25) + 2.0(1.25) = 3.0\) on the right, in kg m, since g cancels.

Stable, unstable and neutral equilibrium

The three kinds of equilibrium differ in what a small displacement does. In stable equilibrium it brings a force or torque that pushes the object back, as for a marble resting in a bowl. In unstable equilibrium the force or torque pushes it further away, as for a ball on a hilltop. In neutral equilibrium the object is simply balanced in its new position, like a ball on a level floor. For objects acted on mainly by gravity there is a quick test: stable if a small displacement raises the cg, unstable if it lowers it, neutral if it leaves its height unchanged. A marble on a saddle is stable one way and unstable the other.

Tipping and the base of support

The base of support is the area enclosed by an object's contact points with the ground, such as the outline of a chair's four legs. An object stays upright while the vertical line through its cg falls inside that base. Tilt it, and its weight's torque about the edge it rests on turns it back, until the cg passes over the edge; then the torque reverses and it topples. For a box of width \(w\) with its cg centred at height \(h\), the critical tilt angle obeys

\tan\theta_c = \frac{w/2}{h}

A wider base or a lower cg makes the angle larger. That is why racing cars are low and wide.

Worked example: when does a crate tip?

A uniform crate is 0.60 m wide and 1.80 m tall, so its cg is at its centre, 0.90 m up. How far can it be tilted about one bottom edge before it topples? 1. It tips when the cg is directly above the edge it pivots on. 2. Half the width is 0.30 m, so \(\tan\theta_c = \frac{0.30}{0.90}\). 3. \(\theta_c = 18.4°\). 4. Now pack the crate so its cg is only 0.60 m up: \(\tan\theta_c = \frac{0.30}{0.60}\) gives \(26.6°\). 5. Check: a lower cg should tolerate a bigger tilt, and it does. This is why heavy items go at the bottom of a van.

Stability in the human body

Standing upright, your cg sits inside the pelvis, a little more than halfway up your body, above a base of support no bigger than the area under and between your feet. That base is small, so muscles make constant small corrections to keep you upright. You widen your stance on a moving train to enlarge the base, and bend your knees to lower your cg when bracing for a tackle. A walking stick adds a contact point and enlarges the base. When you carry a load, you lean to keep the combined cg over your feet: forwards with a heavy rucksack, away from a bag hung on one side, and backwards when holding a box in front.

A strategy for statics problems

Statics is Newton's laws with zero acceleration, plus a torque equation. 1. Confirm the object is in equilibrium, with no linear or angular acceleration. 2. Choose the system and draw a free-body diagram, marking where each force acts, with each weight at its cg. 3. Write \(\sum \tau = 0\) about a pivot chosen at an unknown force, so it drops out. 4. Resolve forces into components and write \(\sum F_x = 0\) and \(\sum F_y = 0\). 5. Check that the sizes, directions and units make sense. A negative answer is not an error: it means the force points the other way from the one you drew.

Worked example: a sign on a strut

A uniform horizontal strut, 2.0 m long and weighing 120 N, is hinged to a wall. A 200 N sign hangs from its outer end, and a cable from that end to the wall makes 30° with the strut. Find the cable tension and the hinge force. 1. Take torques about the hinge. Only the cable's vertical part, \(T\sin 30°\), has a lever arm there. 2.

T\sin 30° \times 2.0 = 120(1.0) + 200(2.0) = 520

so \(T = 520\) N. 3. Horizontal: the hinge pushes out from the wall with \(T\cos 30° = 450\) N. 4. Vertical: \(H_y = 320 - T\sin 30° = 60\) N upwards. 5. Check with torques about the outer end: \(H_y(2.0) = 120(1.0)\) gives 60 N again.

Common mistakes to avoid

First, putting an object's weight anywhere but its cg, which is the midpoint only for a uniform object. Second, calling every balanced position stable; a pencil on its point is balanced but unstable. Third, judging tipping by how low the cg is, instead of whether its vertical line stays inside the base. Fourth, using the full cable tension as if it were perpendicular to a strut; only its perpendicular component has a lever arm about the hinge. Fifth, assuming a hinge force acts along the strut; find both of its components from the equilibrium equations.

Key takeaways

The centre of gravity is where an object's whole weight can be taken to act; in uniform gravity it is the centre of mass, a mass-weighted average position. A displacement brings a restoring push in stable equilibrium, a push further away in unstable equilibrium, and neither in neutral equilibrium. An object stays upright while the vertical line through its cg lies within its base of support; a uniform box tips at tan θc = (w/2)/h, so low and wide means stable. In statics problems, take torques about an unknown force, then balance the force components.

Flashcards

Flashcard

Centre of gravity (cg)

The point where an object's whole weight can be taken to act

Same as the centre of mass in uniform gravity.

Test your understanding

Question 1 of 5

A light rod carries a 3.0 kg mass at x = 0 and a 1.0 kg mass at x = 0.80 m. Where is the centre of gravity?

Question 2 of 5

A cone is balanced on its point. Which kind of equilibrium is this?

Question 3 of 5

A uniform block is 0.40 m wide and 1.20 m tall. At what tilt angle about one bottom edge does it start to topple?

Question 4 of 5

Which change makes a tall bookcase hardest to tip over?

Question 5 of 5

A uniform horizontal strut 1.5 m long, weighing 80 N, is hinged to a wall. A 150 N lamp hangs from its outer end, held by a cable from that end at 30° to the strut. What is the cable tension?

← Previous topicNext topic →