Statics › Section J · Moments of inertia › Topic J.2
Moments of inertia of common shapes
Rectangles, triangles and circles make up most real cross-sections, so their second moments of area are worth deriving once and remembering. The derivations also teach the strip method that handles any other shape.
From definition to formula
The previous topic defined \(I_x = \int_A y^2\,dA\) and evaluated it for particular plates. Doing the integrals with letters for the dimensions turns each result into a formula for every shape of that kind. One warning runs through the whole topic: a formula belongs to one shape and one axis. A rectangle about its base and about its centroid has two different values, so always note where the axis sits before you pick a formula. Every answer here is an area moment, in length to the fourth power.
A rectangle about its base
Take a rectangle of width \(b\) and height \(h\) with its base on the x axis. Slice it into horizontal strips of thickness \(dy\). Every point of a strip is the same distance \(y\) from the axis, so the strip contributes \(y^2\,dA\) with \(dA = b\,dy\). Adding the strips from bottom to top gives
This works because the strips are parallel to the axis; a double integral gives the same answer with an extra step.
A rectangle about its centroid
Move the axis to the rectangle's centroid, halfway up. The strips now run from \(y = -h/2\) to \(h/2\), and
The bar marks a centroidal moment of inertia. It is a quarter of the base value, because no part of the rectangle is now more than \(h/2\) from the axis. Turning the rectangle through a right angle swaps the roles of the sides, so \(\bar{I}_y = hb^3/12\). In every formula the dimension measured perpendicular to the axis is the one that is cubed. Doubling a beam's depth multiplies \(\bar{I}\) by eight; doubling its width only doubles it.
Worked example: a joist on edge or flat
A timber joist has a rectangular cross-section 38 mm by 140 mm. Compare its centroidal moment of inertia about a horizontal axis when it stands on edge and when it lies flat. 1. On edge, the 140 mm side is vertical, so \(b = 38\) and \(h = 140\):
2. Flat, \(b = 140\) and \(h = 38\):
3. The ratio is \((140/38)^2 = 13.6\). Check: the area is the same both ways, yet on edge the joist is about 13.6 times stiffer in bending, which is why floor joists are fixed on edge.
A triangle about its base
Take a triangle with base \(b\) on the x axis and height \(h\). A horizontal strip at height \(y\) shrinks steadily from the full base to nothing at the apex, so its width is \(b(1 - y/h)\). Then
The strip widths do not depend on where the apex sits above the base, so this holds for any triangle about its base, not only a right triangle. It is a quarter of the matching rectangle's value, since much of the triangle's area lies close to the axis.
Strips perpendicular to the axis
Parallel strips need the boundary written as \(x\) in terms of \(y\), which can be awkward. The alternative uses vertical strips for \(I_x\). A vertical strip of width \(dx\) standing on the x axis with height \(y\) is a thin rectangle about its own base, so by the rectangle formula
Add these from left to right. For \(I_y\), the same vertical strip is parallel to the y axis, so \(dI_y = x^2\,y\,dx\). Now only the top boundary \(y = f(x)\) is needed, with the same strips as in the topic Centroids by integration.
Worked example: a parabolic spandrel
A plate is bounded by the x axis, the line \(x = 40\) mm and the curve \(y = x^2/20\), with lengths in millimetres, so it is 80 mm tall at its right edge. Find \(I_y\) and \(I_x\). 1. Vertical strips have height \(y = x^2/20\). 2. About the y axis:
3. About the x axis:
4. Check: horizontal strips of width \(40 - \sqrt{20y}\) from \(y = 0\) to 80 give the same \(I_x\), with more effort.
Circles from rings
For a circle of radius \(r\), straight strips are clumsy, so slice it into thin rings instead. A ring of radius \(\rho\) and thickness \(d\rho\) has area \(2\pi\rho\,d\rho\), and all of it is the same distance \(\rho\) from the centre. That suits the polar moment:
The previous topic showed \(J_O = I_x + I_y\), and a circle looks the same about every diameter, so \(I_x = I_y\). Each is therefore half the polar moment:
If you are given a diameter \(d\), this is \(\pi d^4/64\).
Semicircles, quarter circles and tubes
The x axis splits a circle into two identical halves, so a semicircle about its diameter has half the circle's value, \(\pi r^4/8\). Split again and a quarter circle about either straight edge has \(\pi r^4/16\). These axes lie along edges, not through the centroids of the pieces; the next topic finds the centroidal values. A hollow circle, or tube, of outer radius \(r_o\) and inner radius \(r_i\) is a full circle with the inner one removed, and because integrals over separate areas add,
Tubes keep their material far from the centre, as bicycle frames and scaffolding do.
Worked example: solid bar or tube
A solid round bar of radius 30 mm and a tube of outer radius 50 mm have the same cross-sectional area. Find the tube's inner radius and compare centroidal moments of inertia. 1. Equal areas: \(50^2 - r_i^2 = 30^2\), so \(r_i = 40\) mm. 2. Bar: \(\bar{I} = \pi(30)^4/4 = 0.636 \times 10^6\ \mathrm{mm^4}\). 3. Tube:
4. Check: the ratio is 4.56, equal to \((50^2 + 40^2)/30^2\) because
The same amount of material is more than four times as stiff.
Common mistakes to avoid
First, using \(bh^3/12\) when the axis is at the base, or \(bh^3/3\) when it passes through the centroid. Second, cubing the wrong side: the cubed dimension is the one perpendicular to the axis, so a flat plank has a small \(h\). Third, putting a diameter into \(\pi r^4/4\), which makes the answer 16 times too big. Fourth, using vertical strips with \(dI_x = y^2\,dA\); the points of a vertical strip sit at different heights, so it needs \(y^3/3\,dx\). Fifth, taking \(\pi r^4/8\) as a semicircle's centroidal value; it is about the diameter.
Key takeaways
Parallel strips do one integral for you. A rectangle has I = bh³/3 about its base and Ī = bh³/12 about its centroid; the side measured across the axis gets the cube, so depth matters far more than width. Any triangle has I = bh³/12 about its base. A vertical strip standing on the x axis has dIx = y³/3 dx and dIy = x²y dx. Rings give a circle J = πr⁴/2 and Ī = πr⁴/4 about any diameter. A semicircle has πr⁴/8 about its diameter, a quarter circle πr⁴/16 about either straight edge, and a tube π(ro⁴ − ri⁴)/4.
Flashcards
Flashcard
I = bh³/3
Test your understanding
Question 1 of 5
A rectangle is 60 mm wide and 20 mm tall. What is its moment of inertia about a horizontal axis along its base?
Question 2 of 5
A beam's rectangular cross-section has its depth doubled while its width stays the same. By what factor does its centroidal moment of inertia about the horizontal axis change?
Question 3 of 5
A triangle has a base of 90 mm on the x axis and a height of 60 mm. What is its moment of inertia about the x axis?
Question 4 of 5
A solid circular section has a diameter of 40 mm. What is its moment of inertia about a diameter?
Question 5 of 5
To find Ix of the area under a curve y = f(x) using vertical strips that stand on the x axis, what should each strip contribute?
